The Tactical Rifle Shooters Facebook Group recently showcased tools used to measure case headspace before and after “bumping” the shoulder. After a case is fired, hand-loaders who full-length size their cases will typically bump the shoulders back anywhere from .001″ to .0035″, depending on the rifle and application. With our 6mmBR and Dasher cases we like about .0015″ bump.
You want the amount of case sizing and bump to be the same for all your brass. To ensure uniformity, it makes sense to measure your cases before and after the FL sizing process. When we have time, we check every case. Other folks will simply check the first 3-4 cases coming out of the FL sizing die to ensure the FL die setting is correct and delivering desired headspace/bump.
1. Whidden Gunworks Shoulder Bump Gauge
There are a variety of tools that can be used to measure shoulder bump. Our favorite is a special cartridge-specific bushing made by Whidden Gunworks. The Whidden Shoulder Bump Gauge enables you to adjust your sizing die to the desired measurement. The bump gauge is attached to your calipers with a set screw and determines the measurement from the base to the shoulder of the case. The photo below, from Tactical Rifle Shooters, shows the Whidden Bump Gauge for the .375 CheyTac cartridge.
2. Dave Manson Vertical Comparator with Dial Read-Out
Dave Manson states: “This tool was designed to make life easier for the advanced shooter and re-loader by allowing precise measurement of ammunition, case, and chamber headspace. With this information, the re-loader will be able to fine-tune clearances and fits between his ammunition and chamber, with resultant improvements in accuracy and case life.” The functions of the Manson Comparator are:
1. Measure headspace of factory or reloaded ammunition
2. Quantify chamber headspace by measuring headspace of a fired case
3. Ensure minimal shoulder set-back when setting up re-loading dies
4. Compare base-to-ogive length to ensure consistent bullet-to-rifling relationship.
Hornady’s Lock-N-Load Headspace Comparator system is easy-to-use and handy. You can get a kit with Red bushing-holder body and 5 bushings for $43.43 at Midsouth. Hornady explains: “The Lock-N-Load® Headspace Comparator… gauge measures variations in brass before and after firing or re-sizing. It allows for headspace comparison between fire-formed brass and re-sized brass.” IMPORTANT: Hornady states: “To determine the proper bushing diameter for your cartridge, simply add the neck diameter and the shoulder diameter and divide that number by two. Use the bushing closest to that number.” Hornady offers five: .330″, .350″, .375″, .400″, and .420″.
One tip — We have found the Hornady gauges may vary a little from unit to unit even with the same nominal size. If you have more than one gauge for the same cartridge, test each on your brass — you may then note a slight difference in your bump measurements. Mark one and use that consistently. There is also an Anvil Base Kit that mounts to the opposite blade on the caliper. This provides a more stable surface for the base of your case.
4. L.E. Wilson Case Gage Depth Micrometer
If you are looking for precise “bump” measurements without having to mess with calipers and clamp-on gauge blocks, you may want to consider the L.E. Wilson Case Gage Depth Micrometer (currently $130.00). This takes very precise, repeatable measurements, but you need to know your starting point. The manufacturer explains: “Every reloader should know exactly how much your Full Length Sizing Die is pushing back the shoulder. With the NEW Case Gage Depth Micrometer you can do just that! It has never been easier to measure you cases headspace before and after sizing. The Depth Mic allows you to slip the micrometer perfectly over the top of the Gage with your case inserted into the Gage and take a measurement. Micrometer has graduations of .001″. The Case Gage Depth Micrometer is set to a zero of .100″ on the scale at our factory. Because of differences in ‘feel’ and temperature, we include a the Gage Block for you to test Zero and to adjust if necessary.”
5. Pistol Brass Case DIY Bump Gauge
Last is a “field expedient” set-up if you do not have any of the comparator tools shown above. A sized .45 ACP case (or other suitable pistol case) can be used to measure shoulder bump. The mouth of the pistol case sits on the shoulder of your rifle cartridge brass.
Make sure the .45 ACP case is trimmed square and that it is round. We recommend you first run it through an expander, then size it, trim it and chamfer. Next, take the .45 ACP case and slip it over the neck of a fired, unsized rifle case with the primer removed. Align the two cases between the jaws of your calipers and note the length from rim to rim (See left photo below).
OK, now you have the length for a fired rifle case BEFORE sizing. Next, take a full-length sized rifle case (without primer) and do the same thing, placing the .45 ACP case over the neck of the FL-sized case (Right Photo). The difference between the two numbers is the amount of “bump” or set-back you are applying to the shoulder. Here the difference is .0015″. The amount of bump you need varies with your chamber and your load, but .0015-.002″ is a good initial setting.
Share the post "Five Cool Tools to Measure Shoulder Bump on Your Cases"
At the request of our readers, we provide select “Deals of the Week”. Every Sunday afternoon or Monday morning we offer our Best Bargain selections. Here are some of the best deals on firearms, hardware, reloading components, optics, and shooting accessories. Be aware that sale prices are subject to change, and once clearance inventory is sold, it’s gone for good. You snooze you lose.
NOTE: All listed products are for sale to persons 18 years of age or older. No products are intended for use by minors.
This RCBS Rock Chucker Supreme Master Reloading Kit makes it easy to get started reloading — with everything you need into one package. The kit includes: RockChucker Supreme Master Reloading Press, Universal Case Loading Block, .17-.60 Debur Tool, M500 Mechanical Scale, Uniflow III Powder Measure, Hand Priming Tool, Hex Key Set, Case Lube Kit, Powder Funnel, and Speer Reloading Manual. Right now this kit is just $335.99, a 34% savings!
2. Sportsman’s — Citadel Stars and Stripes M1911 Pistol, $899.99
⏺ Handsome patriotic M1911-A1 pistol to Celebrate 4th of July
Tomorrow is the 4th of July. What better way to celebrate America’s Independence Day than with a patriotic Stars and Stripes M1911 pistol. Citadel’s full-sized M1911 Government has a handsome Cerakoted American flag finish. This is available by itself or with a matching Stars and Stripes ammo can. As on sale right now at Sportsman’s Outdoor Superstore, this pistol is $899.99 — $310 off the regular price.
3. Natchez — Frankford Arsenal Platinum Intellidropper, $169.99
⏺ Excellent scale/dispenser out-performs other much more pricey units
If you’re looking to upgrade your powder measure system, check out the Frankford Arsenal Intellidropper. It’s one of the most advanced, intelligent, and precise electronic powder measures on the market today. The Intellidropper features a proprietary powder calibration button for fast and accurate powder measurements. Auto and manual trickle capability with up to 250 grains of powder per throw. Holds more than 7,000 grains of powder and offers +/- 0.1 grain accuracy.
4. Creedmoor Sports — Shoulder Datum Tool, $49.95
⏺ Handy tool allows you to gauge bump for multiple cartridge types
Measure your shoulder datum with the NEW Creedmoor Sports Shoulder Datum Tool. Sometimes you just want to bump the shoulder back .002″ to .003″ to preserve brass life while still ensuring it will feed in your rifle. It can also help with accuracy in some cases if the shoulder is already touching the inside of the chamber. It can also be helpful to know how the brass stretches during firing. If it’s being stretched a lot, especially in a bolt gun, this can mean the headspace may be excessive, or that the bolt isn’t making firm contact on the lugs.
5. EuroOptic — SIG Sauer Pistol Sale, Save up to $180
⏺ Excellent, accurate, reliable match and defense pistols on sale
Sig Sauer makes some of the finest pistols on the market for target shooting, self-defense, and concealed carry. Head over to EuroOptic for the Sig Sauer Sale where you’ll find pages of models to choose from all at lower than normal prices.
6. Amazon — Peregrine Magnetic Gun Caddy, $13.17
⏺ Unique accessory for handy safe storage; can be used on vehicle
Keeping your rifles steady and upright in safe, shop, or vehicle can be a challenge. An easy way to keep long guns secure is the Peregrine Field Gear Magnet Gun Caddy. This works great inside a safe, and can also attach magnetically to a vehicle. The magnetic gun caddy is an extra set of hands when you need to rest your unloaded firearm. It’s small and lightweight so it fits in your vest pocket, glove compartment, or range bag.
7. Amazon — Birchwood Casey .22 LR Target Rack, $36.94
Spending the day plinking with a .22 LR can be a lot of fun and relaxing. A great way to practice is with a dynamic target such as the Birchwood Casey Steel Resetting Target. Shoot the four lower plates then hit the upper plate to reset the group. NOTE — This target is designed for .22 LR Rimfire rifles and pistols. This Rimfire Target features a twist design with no welds to break.
8. Amazon — Simhevn Electronic Digital Caliper, $9.49
⏺ Amazing low price on digital calipers — great for a backup unit
One of the keys to accurate reloading is having a good set of calipers for measuring everything from bullets to brass. An inexpensive but effective version is the Simhevn Electronic 6″ Digital Caliper. These budget-price electronic calipers offer a nice LCD display screen, which automatically turns off after 5 minutes of use. These calipers come with a pre-installed battery plus a spare battery.
9. Amazon — Boosteady Gun Swabs, $10.99
⏺ Handy swabs for cleaning rifles and pistols — goodo inside actions
Cleaning guns can be challenging enough without worrying about getting gunk out of tiny corner and nooks. For those areas we like BOOSTEADY 6-Inch Cotton Gun Cleaning Swabs. Right now get 300 swabs for just $10.99 on Amazon. These will work for a variety of calibers and can reach into hard to reach places. This makes them great for slides, receivers, chambers, magazine housings, and breeches.
Share the post "BargainFinder 406: AccurateShooter’s Deals of the Week"
At the request of our readers, we provide select “Deals of the Week”. Every Sunday afternoon or Monday morning we offer our Best Bargain selections. Here are some of the best deals on firearms, hardware, reloading components, optics, and shooting accessories. Be aware that sale prices are subject to change, and once clearance inventory is sold, it’s gone for good. You snooze you lose.
NOTE: All listed products are for sale to persons 18 years of age or older. No products are intended for use by minors.
1. Bruno Shooters — Primers on Sale, Free Shipping, Free Hazmat
⏺ With 5K Primers Sealed Case $0 Hazmat and FREE Shipping
Primers are still in short supply these days. Some sellers are still charging over $200 per thousand. But Bruno’s is running a Springtime Primer Special that can save you big bucks. And if you purchase a sealed box of 5000 primers Bruno’s includes FREE HAZMAT and FREE Shipping. That can save you $50-$70 per shipment. In stock now are a variety of CCI, Federal, and Remington primers, with some European primers due soon. Prices start at $92.95 per thousand, with 5000 minimum for free shipping with $0 hazmat fee.
2. Creedmoor Sports — American Bullet Company Match Bullets, $18.95 – $38.95 per hundred
⏺ Top-quality bullets at half what some others cost
Creedmoor Sports has a new line of American Bullet Co. Match-Grade Bullets. These .224- and .308-caliber bullets are first run — no blems or seconds — with all bullets in each box from a single lot. A great value, these bullets let you shoot more without breaking the bank. The .224 bullets are offered in 75gr HPBT, 77g HPBT, and 77gr Tipped. The .308 bullets are 155gr, 169gr, and 175gr HPBT.
3. Midsouth — New Frankford F-1 Single-Stage Press, $128.99
⏺ Versatile press, built-in light, good primer exit, plus FREE shipping
Here’s a handy, single-stage press with some cool features. The new Frankford Arsenal F-1 press has an open front for easy case placement, plus a built-in LED lamp at the top (great for inspecting cases). And after decapping, spent primers go straight down a tube into a catch cylinder (as on a Forster Co-Ax). We think this would be an excellent secondary press used for decapping or bullet seating. The intro price — just $128.99 at Midsouth — is a great deal as you get FREE Shipping. NOTE: This press does NOT have priming capability — you must prime cases with a separate tool. Also, the power cord for the LED light is NOT included. For more details see Frankford Arsenal F-1 Press Review. Here is a review from a recent purchaser: “Amazing press for a great price. The ball bearing ram is smooth and feels right. The leverage is great and all-around operations of the press are [excellent].”
4. EuroOptic.com — Vortex Scope Close-outs, Save 44-54%
⏺ Massive discounts on Vortex scopes for PRS/NRL, varminting, and tactical
5. Midsouth — Aguila .22 LR Ammunition, $34.99 500 rounds
⏺ Large variety of Aguila rimfire ammo at great prices
With the high cost of centerfire components (bullets, brass, primers, powder), more folks are shooting rimfire rifles and pistols. Right now, Midsouth is running a major sale on Aguila rimfire ammo. Choose standard velocity (1130 fps) or high-velocity (1255 fps), solid point or hollowpoint. Ammo starts at just $3.49 for 50 round boxes of 38gr or 40gr ammo. And if you need large quantities, you can get 2000-round bulk packs for just $119.99. That works out to just $0.06 per round — a steal. For varmint work, consider Aguila’s 1700 fps Hyper Velocity Supermaximum 30gr ammo, priced at $7.49/50 rounds.
6. Precision Reloading — Lee PRO 1000 Press Package, $189.99
⏺ Amazing deal on Progressive Press with case feeder for loading pistol ammo
If you want the efficiency of a progressive press, but have a limited budget, consider the Lee Pro 1000 Progressive Reloading Press. This reloading kit includes 3-station press, dies (Carbide FL Sizing, Powder-Through Expanding, and Bullet Seating Dies), 3-Hole Turret, Shell Plate, Powder Measure, Universal Case Feeder, and priming system. Yes that’s right this $189.99 Kit includes the case feeder! Foe the $189.99 sale price you can order the kit for these cartridge types: 9mm Luger (9x19mm), .38 Auto/.38 Super, .38 Spl/.357 Mag, and .45 Colt. Just get other dies to load other cartridge types. NOTE: Lee cautions that “Only CCI or Remington brand primers are safe to use with this press”.
7. Palmetto SA — Leupold LRF and Binoculars Combo, $50 Off
⏺ Great price on Laser Rangefinder and Binoculars bundle
Here’s a nice Leupold Optics Combo for a hunter/varminter. For just $279.99 you get BOTH the Leupold RX-1400i TBR/W Laser Rangefinder (LRF), plus the quality Leupold BX-1 McKenzie 10×42 HD binoculars. The RX-1400i LRF is rated for 1400 yards, and offers angle ballistics correction. The display is bright red — good for both sunny days and darker dusk/dawn conditions. The binoculars come with GO Afield shoulder strap, binocular case, lens covers, and lens cloth.
8. Palmetto SA — Taurus TX22 Competition, $415.36
⏺ Affordable .22 LR match pistol with compensator has earned positive reviews
Rimfire pistols let you enjoy action pistol competitions without spending a ton of money. Among .22 LR pistols, the Taurus TX22 Competition SCR offers great performance for the price. The TX22 Competition SCR builds features a precision-engineered slide and match-grade bull barrel. The “skeletonized” slide with enlarged ejection port is designed so that a red dot optic can be mounted to the barrel. That helps prevent problems during ejection of empty shells. Taurus claims this mounting configuration enhances accuracy compared to a slide-mounted optic platform.
9. Amazon — NEIKO 6″ Digital Calipers, $25.89
⏺ Good, reliable digital calipers at attractive price
Every handloader needs to measure shoulder bump, cartridge length, and other dimensions. A good set of calipers is essential. If you need calipers, check out the NEIKO Electronic Digital Calipers. The tool’s body/frame is constructed of finely polished stainless steel with a knurled thumb roller and locking screw that ensures smooth sliding and accurate positioning. If you’re getting started in reloading or are looking for a back-up set of calipers, this is a good option.
⏺ Good compact muffs for the price with a good 26dB SNR
We say it all the time but don’t ever shoot without quality hearing protection. Consider these Vanderfield folding ear muffs. Priced at just $15.99, these come in a variety of colors (black, brown, green, gray, red, purple, pink) so you can easily tell yours apart from others. The 26dB SNR sound protection rating is above average for compact muffs. For maximum protection use plugs under the muffs. (FYI, “SNR” or Single Number Rating, is the EURO equivalent of the NRR noise rating in the USA.)
Share the post "BargainFinder 397: AccurateShooter’s Deals of the Week"
Bolt Action Reloading is a popular YouTube channel that has amassed nearly 75,000 subscribers. For this Saturday Video Showcase we’ve selected six interesting videos. If you’re getting started in reloading, definitely watch the video on Five Common Mistakes. And all handloaders can benefit from the videos which covers affordable tools, all under $50.00.
Five Common Mistakes Made by Novice Handloaders
This video spotlights five (5) common mistakes made by people when they get started hand-loading ammunition. These are some of the most common errors and misconceptions that affect “newbie” reloaders. Here are the five common problems encountered by folks getting started in handloading:
1. Not Using LOAD DATA from a Reliable Source — Use verified, properly developed load data from a powder maker or bullet maker. Don’t trust private social media posts. And always start conservatively.
2. Inconsistent Case Sizing — this can be the result of sloppy die set-ups or not knowing how to measure cases correctly.
3. Cartridge Overall Length (COAL) Variances — Don’t assume that COAL book values apply to your ammo. You should measure your own cases based on your chamber, headspace, and bullet choice. AccurateShooter.com recommends you use QuickLoad or Gordon’s Reloading Tool software to help adjust loads for different COAL.
4. Hand-Loading Is Not Always a Money-Saver — For a cartridge you don’t shoot much (say a .30-06 for hunting only), hand-loading might not save you money once you count the cost of dies and tools.
5. Reloading Kits Are NOT Complete — Don’t assume that the $500 reloading kit you acquired (with press, powder measure, scale etc.) has all the components and tools you actually need. You will still need dies, comparators, and many other tools.
Primer Pocket Uniforming — Is It Worth the Time and Effort?
With Lapua and Peterson brass we have had very good results — great accuracy and with low ES and SD — using brass that has NOT had the primer pockets uniformed with some kind of cutter. We always do check to make sure there are no flakes or obstructions in the flash holes, but we generally do NOT need to cut into the pockets. But with lesser brands of brass you can benefit from uniforming your primer pockets. And yes there are some top shooters who DO uniform pockets even on premium-brand brass. That is up to you. This video explains the process for primer pocket uniforming and looks at some test results.
Developing a Load — OCW vs. 10-Round Ladder
This video talks about two methods of determining an accurate load. We include this video here because many people are curious about Optimal Charge Weight (OCW) load development. Frankly, however, we believe there are better, more reliable ways to find a good load — many people have wasted many hours and much barrel life on the OCW quest. NOTE: With a good cartridge of known accuracy, such as a 6mmBR or 6mm Creedmoor using top-quality brass, we really do NOT advocate either method described in this video. We suggest you do a search to find the best bullet choice and powder choices. Then, if you are shooting from the bench with a custom barrel, consider starting in the lands, about .003-.005 past first touch. NOT full jam!! If you are shooting in conditions where you may have to unload a round during a match, start .020″ back from first touch. Chronograph every round. Shoot three-shot groups at 100 yards, looking to keep all shots touching. Many people doing OCW waste a ton of time (and barrel life). And one bit of advice for people with average factory barrels — it may be pointless to expect anything much under 1 MOA from that barrel no matter what you do.
Handloading Cool Tools — All Under $50.00
Along with powder measure, dies, and reloading press, there are a wide variety of tools that can help achieve good results when handloading ammo. This Bolt Action Reloading video identifies ten (10) tools that can be acquired for $50.00 or less. Here is the list:
1. Check Weights (00:20) — These help ensure your scale is measuring properly.
2. Digital Calipers (00:57) — You can spend $200+ on calipers, but you can get good results from caliper that cost less than $50.00, and every reloader should have a back-up set of calipers.
3. Comparator Sets (01:26) — These are fittings that attach to calipers. Bullet Comparators are sized to fit a bullet diameter to get reliable base-to-ogive measurements. Case comparators fit the neck of the cartridge, allowing you to measure shoulder bump.
4. Stock Case Remover (02:48) — This allows you to remove a brass case that may be stuck in a die.
5. Imperial Sizing Die Wax (03:20) — There are many types of case lubricants, but Imperial Die Wax is still a popular choice and very affordable.
6. LEE Cutter and Lock Stud (03:44) — This is a cheap way to trim cases. We prefer a Forster trimmer or a deluxe power trimmer but LEE system is inexpensive.
7. Chamfering and Deburring Tools (04:38) — After brass is trimmed to length you need to chamfer and deburr the case necks. Good chamfering/deburring tools are “must have” items for hand-loaders.
8. Case Neck Brushes (05:50) — If you don’t tumble your brass it’s a good idea to brush the inside of your fired cases before seating bullets. A couple swipes is all it takes — and you may find you get more consistent seating if you leave a bit of carbon in the necks.
9. Primer Pocket Swage Gauge (Ballistic Tool) (06:24) — These little tools let you check the dimensions of your primer pockets.
10. Decapping Die (06:57) — The decapping die removes spent primers without sizing the case. This is very handy if you want to remove primers before tumbling brass. NOTE: If your cases have small-diameter flash-holes you need to check the diameter of the decapping rod.
11. Powder Trickler (07:40) — A good trickler is an absolute “must have” when manually weighing each charge. The trickler allows you to add a couple grains at a time.
12. Powder Funnel with Drop Tube (08:45) — While most folks have a basic funnel, a deluxe funnel with a drop tube helps to get a full charge and more consistent powder density.
13. Kinetic Bullet Puller (09:36) — This is like a hammer that holds a loaded round. Using kinetic energy this tool can unseat a bullet with a couple of whacks. However, if you must unload a large quantity of rounds you’ll want a cam-lock bullet puller (09:58) that works with your press.
14. Caliber Specific Reloading Trays (10:28) — These are handy if you are loading specific cartridges. There is less wobble for each round.
Setting Neck Tension with Expanders and/or Bushings
There are three main ways (in addition to collet dies), by which you can set the neck diameter on cartridge brass and thereby control neck tension or the “grip” on the seated bullet. First, the sizing die itself can reduce the neck diameter. This can be a fitted die with the neck honed to a precise diameter. Or, the die can take neck bushings, which allow a range of neck tensions via different bushing internal diameters. Because they allow a wide range of tension settings, bushing dies are popular and effective. You can also have a die that takes the neck dimension down a few thousandths, but then have an expander mandrel that brings the neck inside diameter to an exact dimension. This has the advantage of keeping the INSIDE of the neck perfectly round, with any variances in neck-wall thickness pushed to the outside. This Bolt Action Reloading video explains the use of neck bushings and expander mandrels.
Full-Length-Sizing vs. Neck-Sizing of Cases
NOTE: At AccurateShooter.com we recommend that handloaders always full-length size their brass for many important reasons. Virtually all champion shooters in multiple disciplines full-length size their brass. Full-length sizing can achieve record-setting accuracy, and, importantly, it offers consistent shoulder bump with each loading. But we know that people are curious about neck-sizing, so we are including this video.
This video compares identical charge-weight loads tested with full-length-sized 6.5 Creedmoor brass vs. neck-sized 6.5 Creedmoor brass. The tester states: “I use the 142gr Sierra Match King HPBT loaded with Alliant Reloder 16. There is velocity and group data at 150 yards. FYI, we recommend always full-length sizing most cartridge brass, bumping the shoulder about .003″ (or more if required in a semi-auto).”
Share the post "Saturday Movies: Six Bolt Action Reloading Channel Videos"
At the request of our readers, we provide select “Deals of the Week”. Every Sunday afternoon or Monday morning we offer our Best Bargain selections. Here are some of the best deals on firearms, hardware, reloading components, optics, and shooting accessories. Be aware that sale prices are subject to change, and once clearance inventory is sold, it’s gone for good. You snooze you lose.
NOTE: All listed products are for sale to persons 18 years of age or older. No products are intended for use by minors. Prices may vary for Amazon Prime members.
⏺ Good alternative to bulky, heavy electronic muffs
Electronic earmuffs work well but they can be heavy and bulky. And they can interfere with cheek weld. If you want the benefits of electronics but the comfort of ear plugs try the Caldwell E-MAX Shadow electronic ear plugs which boast a 23 decibel NRR (Noise Reduction Rating). Experience high quality stereo sound while confidently protecting your hearing. With six sizes of included foam tips, you’ll find a custom fit for your ear to ensure proper noise cancellation and hearing protection.
2. Midsouth — CCI Bargain Rimfire Ammo in Stock
⏺ Large inventory of CCI Rimfire ammo starting at 9 cents per round
More people than ever are getting rimfire rifles for plinking and/or matches. Rimfires are inexpensive to shoot, and the reduced noise and recoil are big positives. If you need some .22 LR rimfire ammunition check out the CCI .22 LR ammo sale at Midsouth. There’s a wide variety of CCI rimfire ammo on sale, starting at $4.50 per 50ct box. This is a great chance to pick up quality .22 LR ammo at attractive prices.
3. Brownells — $25 Gift Card Bonus with $100 Gift Card Purchase
⏺ Spend $100, get $25 Gift Card back with Brownells promo
Do you like giving gift cards for the holidays? For a limited time you can pick up a FREE $25 gift card with the purchase of $100 in Brownells gift cards. That’s like getting a 25% rebate! This is a great deal and good way to treat someone else AND yourself.
⏺ Very good spotting scope with great long eye relief
Whether shooting at matches or just target shooting having a good spotting scope is a must. A great choice is this Kowa TSN-82SV Combo on sale for $975, a $110 savings. This item includes the highly-rated 82SV spotting body, plus an excellent 25X LER (Long Eye Relief) eyepiece AND a deluxe protective cover. NOTE: With its fixed-power Long Eye Relief eyepiece, this scope works great for prone work, mounted right next to the shooter. However, for long-range spotting duties you may want a unit fitted with a higher-magnification zoom eyepiece.
5. Palmetto SA — Taurus TX 22 .22 LR Pistol Sale, $276.85
⏺ Great price on a very good rimfire pistol
If you’re looking to keep ammo costs down by training with .22 LR rimfire handgun, consider this Taurus TX 22 pistol. Taurus TX 22s have earned very positive reviews from purchasers. The frame has comfortable ergonomics and the Taurus Pittman Trigger System (PTS) offers a very good trigger pull. This is a good choice for a first .22 LR rimfire pistol, at a very good price — starting at $276.85.
6. Amazon — 3″ Splatter Squares On A Roll, $19.99
⏺ Cool product — stick-on grid targets with splatter effect
Splatter targets are popular but the cost of large-size bullseye splatter targets adds up quickly. A cool alternative are these Pistep Splatter Shooting Targets. These are handy “reactive” targets that show a yellow splatter on shot locations. Each roll contain 250 three-inch-square stick-on grids. Each sticker has nine 1″ squares on it so determining group size is easy. For a shooter with an accurate rifle, these 3″ x 3″ splatter squares can work better than a large splatter bullseye target.
Don’t want a gun case that screams “There’s a rifle inside”? If you need to transport small rifles discreetly, check out the Darekuku 30″ Rifle Backpack Bag. The main compartment has padded protection for two rifles. The handy shoulder straps can be covered with a zip-over panel. There is a zipper-access top compartment and a large secondary compartment (with inner mesh pocket and MOLLE straps) to hold ammo, Kestrel, muffs, targets, or other accessories. We like this case to carry a carbine with folding stock. It’s a steal at just $49.99.
It’s getting easier to stock up on ammunition and .223 Rem is the most popular rifle cartridge. If you need a good supply of .223 Rem ammo, consider this PMC 1000-round case of .223 Rem at Locked & Loaded. This is one of the best deals we’ve seen on quality .223 Rem ammo in quite some time.
9. Amazon — NEIKO 6″ Digital Calipers, $25.99
⏺ Good, reliable digital calipers at attractive price
Every handloader needs to measure shoulder bump, cartridge length, and other dimensions. A good set of calipers is essential. If you need calipers, check out the NEIKO Electronic Digital Calipers. The tool’s body/frame is constructed of finely polished stainless steel with a knurled thumb roller and locking screw that ensures smooth sliding and accurate positioning. If you’re getting started in reloading or are looking for a back-up set of calipers, this is a good option.
10. Graf & Sons — Sierra Ammo Sale with Rebate
⏺ Nice rebate on quality Sierra hunting and defense ammo
Did you know that Sierra makes hunting and self-defense ammo? You can grab Outdoor and Sports Master ammo on sale PLUS there’s a rebate that takes $3 off 1 box or $10 off 2 boxes. NOTE: These boxes contain TWENTY (20) rounds only. These are NOT 50-rd boxes.
Share the post "Bargain Finder 373: AccurateShooter’s Deals of the Week"
The Tactical Rifle Shooters Facebook Group recently showcased tools used to measure case headspace before and after “bumping” the shoulder. After a case is fired, hand-loaders who full-length size their cases will typically bump the shoulders back anywhere from .001″ to .0035″, depending on the rifle and application. With our 6mmBR and Dasher cases we like about .0015″ bump.
You want the amount of case sizing and bump to be the same for all your brass. To ensure uniformity, it makes sense to measure your cases before and after the FL sizing process. When we have time, we check every case. Other folks will simply check the first 3-4 cases coming out of the FL sizing die to ensure the FL die setting is correct and delivering desired headspace/bump.
1. Whidden Gunworks Shoulder Bump Gauge
There are a variety of tools that can be used to measure shoulder bump. Our favorite is a special cartridge-specific bushing made by Whidden Gunworks. The Whidden Shoulder Bump Gauge enables you to adjust your sizing die to the desired measurement. The bump gauge is attached to your calipers with a set screw and determines the measurement from the base to the shoulder of the case. The photo below, from Tactical Rifle Shooters, shows the Whidden Bump Gauge for the .375 CheyTac cartridge.
2. Dave Manson Vertical Comparator with Dial Read-Out
Dave Manson states: “This tool was designed to make life easier for the advanced shooter and re-loader by allowing precise measurement of ammunition, case, and chamber headspace. With this information, the re-loader will be able to fine-tune clearances and fits between his ammunition and chamber, with resultant improvements in accuracy and case life.” The functions of the Manson Comparator are:
1. Measure headspace of factory or reloaded ammunition
2. Quantify chamber headspace by measuring headspace of a fired case
3. Ensure minimal shoulder set-back when setting up re-loading dies
4. Compare base-to-ogive length to ensure consistent bullet-to-rifling relationship.
In addition to the Dial Indicator and Stand, the $130.00 Vertical Comparator is supplied with multiple Datum Blocks of precise length and inside diameter (.3300″/.3750″/.4000″/.4375″). MORE INFO HERE — Catalog page 20.
3. Hornady L-N-L Headspace Comparator System
Hornady’s Lock-N-Load Headspace Comparator system is easy-to-use and handy. You can get a kit with Red bushing-holder body and 5 bushings for $43.43 at Midsouth. Hornady explains: “The Lock-N-Load® Headspace Comparator… gauge measures variations in brass before and after firing or re-sizing. It allows for headspace comparison between fire-formed brass and re-sized brass.” IMPORTANT: Hornady states: “To determine the proper bushing diameter for your cartridge, simply add the neck diameter and the shoulder diameter and divide that number by two. Use the bushing closest to that number.” Hornady offers five: .330″, .350″, .375″, .400″, and .420″.
One tip — We have found the Hornady gauges may vary a little from unit to unit even with the same nominal size. If you have more than one gauge for the same cartridge, test each on your brass — you may then note a slight difference in your bump measurements. There is also an Anvil Base Kit that mounts to the opposite blade on the caliper. This provides a more stable surface for the base of your case.
4. L.E. Wilson Case Gage Depth Micrometer
If you are looking for precise “bump” measurements without having to mess with calipers and clamp-on gauge blocks, you may want to consider the L.E. Wilson Case Gage Depth Micrometer. This takes very precise, repeatable measurements, but you need to know your starting point. The manufacturer explains: “Every reloader should know exactly how much your Full Length Sizing Die is pushing back the shoulder. With the NEW Case Gage Depth Micrometer you can do just that! It has never been easier to measure you cases headspace before and after sizing. The Depth Mic allows you to slip the micrometer perfectly over the top of the Gage with your case inserted into the Gage and take a measurement. Micrometer has graduations of .001″. The Case Gage Depth Micrometer is set to a zero of .100″ on the scale at our factory. Because of differences in ‘feel’ and temperature, we include a the Gage Block for you to test Zero and to adjust if necessary.”
5. Pistol Brass Case DIY Bump Gauge
Last is a “field expedient” set-up if you do not have any of the comparator tools shown above. A sized .45 ACP case (or other suitable pistol case) can be used to measure shoulder bump. The mouth of the pistol case sits on the shoulder of your rifle cartridge brass.
Make sure the .45 ACP case is trimmed square and that it is round. We recommend you first run it through an expander, then size it, trim it and chamfer. Next, take the .45 ACP case and slip it over the neck of a fired, unsized rifle case with the primer removed. Align the two cases between the jaws of your calipers and note the length from rim to rim (See left photo below).
OK, now you have the length for a fired rifle case BEFORE sizing. Next, take a full-length sized rifle case (without primer) and do the same thing, placing the .45 ACP case over the neck of the FL-sized case (Right Photo). The difference between the two numbers is the amount of “bump” or set-back you are applying to the shoulder. Here the difference is .0015″. The amount of bump you need varies with your chamber and your load, but .0015-.002″ is a good initial setting.
Share the post "Measure That Bump — Five Cool Tools to Measure Shoulder Bump"
The Tactical Rifle Shooters Facebook Group recently showcased tools used to measure case headspace before and after “bumping” the shoulder. After a case is fired, hand-loaders who full-length size their cases will typically bump the shoulders back anywhere from .001″ to .0035″, depending on the rifle and application. With our 6mmBR and Dasher cases we like about .0015″ bump.
You want the amount of case sizing and bump to be the same for all your brass. To ensure uniformity, it makes sense to measure your cases before and after the FL sizing process. When we have time, we check every case. Other folks will simply check the first 3-4 cases coming out of the FL sizing die to ensure the FL die setting is correct and delivering desired headspace/bump.
1. Whidden Gunworks Shoulder Bump Gauge
There are a variety of tools that can be used to measure shoulder bump. Our favorite is a special cartridge-specific bushing made by Whidden Gunworks. The Whidden Shoulder Bump Gauge enables you to adjust your sizing die to the desired measurement. The bump gauge is attached to your calipers with a set screw and determines the measurement from the base to the shoulder of the case. The photo below, from Tactical Rifle Shooters, shows the Whidden Bump Gauge for the .375 CheyTac cartridge.
2. Dave Manson Vertical Comparator with Dial Read-Out
Dave Manson states: “This tool was designed to make life easier for the advanced shooter and re-loader by allowing precise measurement of ammunition, case, and chamber headspace. With this information, the re-loader will be able to fine-tune clearances and fits between his ammunition and chamber, with resultant improvements in accuracy and case life.” The functions of the Manson Comparator are:
1. Measure headspace of factory or reloaded ammunition
2. Quantify chamber headspace by measuring headspace of a fired case
3. Ensure minimal shoulder set-back when setting up re-loading dies
4. Compare base-to-ogive length to ensure consistent bullet-to-rifling relationship.
In addition to the Dial Indicator and Stand, the $130.00 Vertical Comparator is supplied with multiple Datum Blocks of precise length and inside diameter (.3300″/.3750″/.4000″/.4375″). MORE INFO HERE — Catalog page 20.
3. Hornady L-N-L Headspace Comparator System
Hornady’s Lock-N-Load Headspace Comparator system is easy-to-use and handy. You can get a kit with Red bushing-holder body and 5 bushings for $40.12. Hornady explains: “The Lock-N-Load® Headspace Comparator… gauge measures variations in brass before and after firing or re-sizing. It allows for headspace comparison between fire-formed brass and re-sized brass.” IMPORTANT: Hornady states: “To determine the proper bushing diameter for your cartridge, simply add the neck diameter and the shoulder diameter and divide that number by two. Use the bushing closest to that number.” Hornady offers five: .330″, .350″, .375″, .400″, and .420″.
One tip — We have found the Hornady gauges may vary a little from unit to unit even with the same nominal size. If you have more than one gauge for the same cartridge, test each on your brass — you may then note a slight difference in your bump measurements. There is also an Anvil Base Kit that mounts to the opposite blade on the caliper. This provides a more stable surface for the base of your case.
4. L.E. Wilson Case Gage Depth Micrometer
If you are looking for precise “bump” measurements without having to mess with calipers and clamp-on gauge blocks, you may want to consider the L.E. Wilson Case Gage Depth Micrometer. This takes very precise, repeatable measurements, but you need to know your starting point. The manufacturer explains: “Every reloader should know exactly how much your Full Length Sizing Die is pushing back the shoulder. With the NEW Case Gage Depth Micrometer you can do just that! It has never been easier to measure you cases headspace before and after sizing. The Depth Mic allows you to slip the micrometer perfectly over the top of the Gage with your case inserted into the Gage and take a measurement. Micrometer has graduations of .001″. The Case Gage Depth Micrometer is set to a zero of .100″ on the scale at our factory. Because of differences in ‘feel’ and temperature, we include a the Gage Block for you to test Zero and to adjust if necessary.”
5. Pistol Brass Case DIY Bump Gauge
Last is a “field expedient” set-up if you do not have any of the comparator tools shown above. A sized .45 ACP case (or other suitable pistol case) can be used to measure shoulder bump. The mouth of the pistol case sits on the shoulder of your rifle cartridge brass.
Make sure the .45 ACP case is trimmed square and that it is round. We recommend you first run it through an expander, then size it, trim it and chamfer. Next, take the .45 ACP case and slip it over the neck of a fired, unsized rifle case with the primer removed. Align the two cases between the jaws of your calipers and note the length from rim to rim (See left photo below).
OK, now you have the length for a fired rifle case BEFORE sizing. Next, take a full-length sized rifle case (without primer) and do the same thing, placing the .45 ACP case over the neck of the FL-sized case (Right Photo). The difference between the two numbers is the amount of “bump” or set-back you are applying to the shoulder. Here the difference is .0015″. The amount of bump you need varies with your chamber and your load, but .0015-.002″ is a good initial setting.
Share the post "Shoulder Bump — Five Cool Tools to Measure Your Bump"
Sierra Bullets asked a few hand-loaders to reveal their favorite reloading tool or accessory: “What is your favorite ‘don’t know how you ever lived without it’ piece of reloading equipment?” Some of the answers are listed below. We were interested to see some high-tech, micro-processor items mentioned, such as the AMP Annealer, and the AutoTrickler powder dispenser. Old standbys, such as the rugged RCBS Rockchucker and Dillon 650, also made the favorites list. You can nominate your own favorite reloading hardware in the comments section of the Sierra Bullets Blog.
Sierra Bullets Ballistic Technician Philip Mahin answered: “A comparator gauge to measure from the base of a case to the ogive of the bullet. This bypasses the tip of the bullet, so I can repeat the same seating depth the next time I visit a specific combination.”
Bill, Editor of Rifleshooter.com, answered: “I have so many favorite reloading tools, it’s hard to pick one. But if I had to, it would be my Forster Co-Ax press. I like the ease [with which] you can change dies and that it doesn’t require traditional shell holders. It’s a great tool to have!”
Sierra Bullets Ballistic Technician Duane Siercks answered: “I don’t know that you would actually call this equipment, but the item that comes to mind would be my reloading room/shoot house. I had always had to squeeze everything into a corner or even an unheated shed. After we bought our current house, I built a garage and placed it so that I had a window looking down a 250-yard range. I built a dedicated room with heat and A/C. It contains my reloading bench and a shooting bench. The shooting bench lets me slide open the window and shoot down the range. It is very handy to not have to load everything up to go to the range. It also makes load development a lot simpler and efficient. I don’t know how I ever got along without it.
I also wonder what I did before I acquired the Lyman 1200 DPS Powder Dispenser. This has made the process so much simpler and much easier. I also have a Lee Precison Universal Decapping Die that I would gladly spend the money on again. This may be a small thing, but it certainly is handy. The Lee would accommodate some very large cases that some of the others were too small for.”
Jon Addis answered: “Putting an A&D FX-120i scale with AutoTrickler and Auto-Throw on the bench has changed the way I reload. It’s kernel accurate in about 15 seconds. Saves time and reduces a variable. And of course, the system is made better by the Area 419 Billet Adjustable base for the trickler and Billet Powder Cup.”
This video shows the AutoTrickler V2 and Auto-Throw Combo:
Sierra Bullets Chief Ballistician Tommy Todd answered: “A brass annealing machine and a RCBS Chargemaster complimented with a Sartorious scale.”
Sierra Bullets Ballistician Gary Prisendorf answered: “RCBS Rock Chucker Press, it’s built like a tank, and it will last me a lifetime.”
Sierra Bullets Production Manager Chris Hatfield also answered: “RCBS Rock Chucker single-stage reloading press.”
Jeremy Kisner answered: “My Giraud trimmer has taken [three operations] and combined them into one easy task. I can now size my brass and then sit down and trim, chamfer, and debur to a 0.001″ tolerance in one motion.”
Dan Blake answered: “My Annealing Made Perfect (AMP) annealer. With consistent neck tension being one of the largest contributions to small Extreme Spread on muzzle velocities, I believe this induction annealer is truly the best on the market.”
This manufacturer-produced video shows how the AMP annealing machine operates:
Trevor Aldinger answered: “Area 419 Master Funnel Kit. In the past I’ve used plastic funnels and even other metal ones. This system fits case necks and flows much better than any others I’ve used, and there is no static since it’s metal. We spend a lot of time and money to get precise charges, I don’t want to lose or miss a kernel because of a cheap funnel.”
Tyler Riley answered: “My RCBS bench primer (priming tool). It has a lot more leverage than a hand primer and still has a good feel to how tight primer pockets are. Makes it much easier on my hands to prime large runs, especially new brass with tight pockets.”
Craig Arnzen answered: “My Annealeez [annealing machine] is one of the best tools in my reloading room. Neck tension is SO important, and annealing every firing really helps with that. This is an inexpensive tool that can anneal a lot of cases at once, and help me produce more consistent ammo.”
Josh Temmen answered: “Time is critical for me so my RCBS Chargemasters are indispensable (pun intended.) They cut down on time at my reloading bench while maintaining the weight tolerances required for long range shooting.”
Josh Bartlett answered: “I have my Dillon 650 set up with Whidden floating tool heads to do decapping and sizing on my match ammo. The case feeder and progressive function of the press save me a TON of time when doing lots of several hundred rounds.”
Ryan Brandt answered: “… A quality set of calipers. My reloading room is full of very nice equipment but little does more to satisfy my perfectionism than a good check with the calipers.”
Share the post "What is Your #1 Favorite Reloading Equipment Item?"
At the request of our readers, we provide select “Deals of the Week”. Every Sunday afternoon or Monday morning we offer our Best Bargain selections. Here are some of the best deals on firearms, hardware, reloading components, optics, and shooting accessories. Be aware that sale prices are subject to change, and once clearance inventory is sold, it’s gone for good. You snooze you lose.
1. Stocky’s — Long Range Composite Accublock Stocks, $219.99
Do you need an electronic powder scale and dispenser? Check out this great deal at Midsouth Shooters Supply. Suggested retail for the ChargeMaster Lite is $299.99 and most vendors are charging $289.99. But now you can get it for just $219.99 at Natchez. So you can save $70.00 with this sale! Put the money saved into bullets or powder. The RCBS ChargeMaster Lite is the modern second generation Scale/Dispenser, descended from the original ChargeMaster. The ChargeMaster Lite features an easy-to-use LCD touchscreen. Dispenser precision is plus/minus 0.1 grains. The unit comes with twin check weights and a convenient plastic cover for the powder pan.
3. CDNN Sports — Walther or S&W 9mm Pistol, Under $280.00
Here are two super deals on quality 9mm handguns. Both these double-stack pistols have 4″ barrels, 16-round capacity, and Picatinny rails in front. The Walther 9mm Creed offers quality German construction for $269.89. Or choose Smith & Wesson’s ergonomic, accurate SD9VE model for $279.99. The S&W’s weight, unloaded, is 22.7 ounces.
4. Powder Valley and Natchez — Varget and H4350 in Stock
Hodgdon’s Varget and H4350 are favorites of competition and tactical shooters. These powders are ideal for popular match calibers such as 6mmBR/Dasher (Varget) and 6mm Creedmoor (H4350). Being in high demand, these powders are often hard to find. But now Natchez Shooters Supply has Varget 1-pounders in stock for $29.99. Natchez also has H4350 in stock, as does Powder Valley Inc.(PVI). Powder Valley has H4350 in stock in both 1-lb ($28.15) and 8-lb ($201.00) containers. Get it while you can. Plus Powder Valley has Alliant Reloder 16 in stock (both 1-lb and 8-lb), a superb alternative if your rifle likes H4350.
5. EuroOptic — Nikon BLACK Riflescope Closeout Sale
If you’re in the market for a tactical scope, check out EuroOptic’s Nikon BLACK riflescope sale. These are good, reliable scopes that rival optics costing twice as much. EuroOptic has a good selection at prices up to 40% off. Choose MOA or MRAD versions with a variety of reticle options. NOTE: These BLACK Nikons are quality scopes that have performed well in the field. You’d have to pay hundreds more to do much better.
6. MidwayUSA — Pro Series Competition Shooting Mat, $34.99
The MidwayUSA Pro Series Competition Shooting Mat is now on sale for just $34.99, 36% off the basic price. The Pro Series mat measures a full 73.5″ x 35.5″. Zippered pockets on the front flap hold ammo or log books. And there are webbing “pockets” for bipod feet so you can pre-load your bipod with forward pressure. This quality mat boasts 0.35″ thick padding, multiple pockets, 6 grommets for staking, and a nice carry strap. It’s easy to transport, rolling up to about nine inches in diameter. User reviews of this $34.99 Shooting Mat have been very positive.
7. Amazon — Vinca Digital Caliper, $21.98
Every handloader needs a set of calipers, and this Vinca unit offers some great features for a very affordable price. Do you ever wish you could take measurements and record them easily for review later? Grab this Vinca Digital Caliper for only $21.98 and you can upload data as you measure. The unit features a RS232 data transfer port that can communicate to a windows laptop or computer with an accessory cable (sold separately). NOTE: The RS232 Data transfer port must connect with “VINCA DTCR-03″ Cable to make data transfer to PC. DO NOT CONNECT WITH REGULAR USB CABLE. This unit comes with one extra battery, and the maker offers a satisfaction guarantee.
8. Cabela’s — Huge Summer Sale, Save up to 40%
Dozens of items are on sale at Cabela’s now through June 10, 2020. You can save on GPS units, binoculars, packs, hiking boots, Knives/multi-tools, fishing gear, and yes firearms too. Check out the full selection of merchandise on Cabela’s Summer Sale Page. You’ll see a dozen featured selections, but scroll down and you can search for sale items by category.
Many of our readers have been curious about Hornady’s A-Tip bullets, but don’t want to spend $75-$85 to try out a full box. In addition, many of the more popular calibers and bullet weights are sold out. Now, thanks to Midsouth Shooters, you can try an A-Tip Sample Pack to see if A-Tips work in your barrel. Choose from four options: 110gr 6mm; 135gr 6.5mm; 153gr 6.5mm; and 250gr .308 caliber. All Sample Packs contain 10 bullets, and cost $9.99 at Midsouth.
Share the post "Bargain Finder 245: AccurateShooter’s Deals of the Week"
Ranges have re-opened in many places, albeit with some social distancing requirements or other health precautions. When you head to the range you’ll want to be prepared. That means collecting all the gear you’ll need at the range. It’s easy to forget small, critical items, so we’ve provided a checklist of the small “extras” you should pack before you head out to the range. In addition to rifle, rests, ammo, targets, and cleaning gear, here are a dozen essentials you should include in your range bag.
• Shell-Holder — If you don’t have calipers, you can use a shell-holder to check for excessive case expansion from hot loads. If a fired case doesn’t slip into the shell-holder easily, your load is definitely TOO HOT.
• Extra Earplugs — Always use ear protection when shooting. We bring a 35mm film canister with extra sets of foam earplugs.
• Hex Wrench or Screwdriver for action screws — Action screws can work loose with time. Always bring the appropriate hex wrench or screwdriver whenever you go to the range.
• Small Wrench for Scope Rings — Check the tension of your scope base and ring fasteners before you go. Bring along a small Torx wrench for the ring screws (or other tool that fits your fasteners).
• Normal and Under-sized Jags — It is often wise to use one-caliber undersize jags when applying solvent with cotton patches. You should have a couple sizes in your range kit.
• Extra Batteries — Bring extra batteries for all your electronic gear — which can include chronograph, windmeter, digital camera, GPS etc.
• Small Notebook and Pen or Pencil — Use the notebook to record chron data, log group sizes, and make notes about wind and weather conditions.
• Adhesive dots — Bring a few sheets of adhesive dots (sold at office supply stores). Use small white or black dots as target pasters. Use larger red or orange dots as aiming points (target centers).
• Folding Chair or Camp Stool — This comes in handy if you’re spotting for another shooter, or if you reload away from the firing line.
• Water Bottle — You can’t shoot well if you’re dehydrated. Bring at least two quarts of water with you and keep a bottle at the bench.
• Surveyors’ Tape and Wood Stakes — You can make inexpensive wind indicators using surveyors’ tape attached to the top of wood stakes.
• Small Plastic Ruler — Use this to measure your group sizes. A transparent (see-through) ruler works best. Rulers are also useful for drawing lines on targets.
This list is not intended to be exclusive. There are many other items you may wish to include. Obviously bring safety glasses, and Sharpie-type pens are always handy to mark targets. We invite our readers to add other “essentials” to the list. The important thing is to plan ahead, packing your key items before you drive to the range.
Share the post "Range Kit Essentials — 12 Handy Items for Days at the Range"
Useful reloading gear does not have to be costly. Here are ten handy (and very inexpensive) items that belong on your loading bench or in your range kit.
• Magnifying Glass – We use a flat, 2″x2″ pocket 4x-8x magnifier. This folds up on itself. Very handy, we use it to inspect bullets and brass. Use this to check your flash holes for burrs, and check the meplats of your bullets before loading.
• Clear 35mm Film Cannister – Use this to transfer the thrown powder charge to the little measuring cup that sits on your scale. That way you don’t get any kernel splash. Also if the charge weight is obviously off, it’s easy to dump back in the measure. A film canister works pretty well as a trickler too.
• Compressed Air in a Can -- Get these at office supply stores. Use the can (with tube attached) to blow crud out of cases after cleaning the neck with a brush, and blast loose debris out of primer pockets.
• Pin Vise – A simple pin vise with a #53 bit is perfect for deburring Lapua PPC and BR flash holes without reaming the flash-holes any larger. The Lapua PPC/BR flash-hole diameter is 1.5 mm, or 0.059″. Amazon.com sells a handy $8.28 pin vise kit with 10 bits, including the ideal 1.5mm bit. Other vendors offer a #53 pin vise bit that measures .0595″ or .060″ (depending or source). You can find pin vises and bits at hobby stores. Note — The model shown below is currently out of stock, but there are many pin vise sets offered from $7 to $15.
• Bounce Dryer Sheets – The common dryer sheets eliminate “static cling” on your plastic reloading parts such as powder measure cylinders, powder funnels, and reloading press plastic bins. Thanks to Doc76251 for this tip.
• Ballistol Aerosol – Try using this versatile lubricant/solvent for full-length sizing. Spray some on a patch and you can wipe the carbon of your case necks. Then, continue to apply a very small amount of Ballistol on the case bodies — just thin sheen is all you need. Ballistol is super slippery, and easy to remove. For general full-length sizing (on small cases) it works great and doesn’t leave a gooey, waxy, or chalky residue. For heavier case-forming jobs, we recommend Imperial Die Wax.
• Shotgun Mop – Stick this in the chamber when using Wipe-Out foaming bore cleaner. This will seal off the chamber so the foam doesn’t flow into your action. For long chambers screw on one section of cleaning rod to aid extraction.
• Colored Sharpie Marking Pens – Mark your bullets ahead of the bearing surface, and the color transfers to the target. This way you can shoot multiple loads at the same point of aim and discern which load shoots the tightest. (Recommended for 300 yards and beyond). With colored bullet tips you can test multiple loads “round robin” to equalize wind effects. When testing seating depths for example, you can mark the longer-seated set of bullets red and the shorter-seated set green and shoot them during the same sequence. Just look at the colored marks on the target to see which grouped better.
• Thin Latex Gloves – You should keep a box of inexpensive, disposable latex gloves (the kind doctors use) in your loading room. These will prevent contamination of primers or powder kernels that you handle directly. Also, use the gloves when handling fine blued tools or firearms to prevent transfering body oils and salts that promote rust.
• Plastic Washers for Neck Mic – If you use a Sinclair Neck-wall Micrometer Gauge with integral stand, you can use thin plastic washers to adjust the height of the case on the mandrel. This makes it much easier to measure the same point on the case neck every time. Thanks to MikeCR for this tip (and photo).
Share the post "Cheap Tricks — Ten Handy Budget Items For Hand-Loaders"
At the request of our readers, we provide select “Deals of the Week”. Every Monday morning we offer our Best Bargain selections. Here are some of the best deals on firearms, hardware, reloading components, optics, and shooting accessories. Be aware that sale prices are subject to change, and once clearance inventory is sold, it’s gone for good. You snooze you lose.
1. Savage — 10% Rebate on Savage, Stevens, and Fox Firearms
Get a 10% Factory Rebate for ALL Savage, Stevens, and Fox firearms purchased from now through May 15, 2019. This Tax Season Rebate could easily save you $50, $100, or even $150 on a fine hunting, tactical, or rimfire rifle. During this Tax Season Savings Event, you’ll receive 10% back on your purchase with a maximum $150 Rebate. The Rebate amount is calculated from the retail purchase price excluding taxes and shipping/handling fees. Rebate submission deadline is 6/14/2019. REBATE FORM HERE.
2. NEW — Frankford Intelli-Dropper Scale/Dispenser, $199.99
Intelli-Dropper Priced Under $200.00: The new Frankford Arsenal Intelli-Dropper will be available very soon at leading vendors such as Midsouth, Grafs.com, and MidwayUSA for around $199.99. This new “Intelli-Dropper” features an advanced brain that can “talk” to a Mobile App on your smartphone via BlueTooth. This way you can store powder and load information on your smartphone and then control the scale/dispenser from the App. The App also has bullet, cartridge, and powder databases. The Intelli-dropper can also manually trickle. Our Deals Editor, F-Class John, just got one of these units and he really likes it. He says the “smart” functionality really is a game-changer. Being able to control the machine with load data stored on your smart phone is great for guys who reload many different cartridge types. Just make sure you know which powder is in the hopper ALL the time!
3. Grafs.com — 10% Off ALL Redding or Saeco Products
Do you need reloading dies, or tools to cast your own bullets? Now’s a great time to grab Redding or Saeco tools at Graf & Sons. ALL in-stock Redding and Saeco products are on sale, discounted 10%. There’s a huge sale selection — over 2000 Redding products and nearly 250 Saeco items. Along with Whidden and Forster, Redding makes high-quality dies and reloading tools. You won’t go wrong with Redding FL Dies, Bushing Dies, and Micrometer-top Seaters. Saeco is an industry leader for bullet casting molds and lubri-sizing hardware. NOTE: Don’t delay — this sale ends Wednesday April 3, 2019 at 11:59 PM Central Time.
4. Palmetto State Armory — PSA 20″ 6.5 Grendel Upper, plus stock, grip, 2-stage trigger, and parts kit: $399.99
The AR is a versatile platform. You can shoot multiple calibers with one lower, and a set of uppers — which can be swapped in seconds. Now you can add a versatile 6.5 Grendel upper for a killer price. We found this PSA 20″ rail-top upper in 6.5 Grendel complete with 20″ stainless 1:8″-twist barrel, 15″ M-Lok handguard, 9310 steel bolt, complete bolt carrier, and adjustable gas block. This kit also includes a stock, plus most of the parts needed to complete your lower (lower receiver NOT included). For $399.99 this is a heck of a deal. Take note — the 6.5 Grendel is a great little cartridge. It mag-feeds fine and you can get superb Lapua brass. The 6.5 Grendel is accurate, efficient, and excellent for BOTH precision target work AND deer hunting. For this price, with a modern 6.5 caliber cartridge, this is a great deal, and could be a significant upgrade for your AR15-platform rig.
5. March Optics — All Scopes on Sale
Every time we head to a match we see more and more March Optics on the line and there’s a good reason why. March offers some amazing scopes, offering incredible clarity, sharpness, and magnification ranges you won’t find on other scope series. If you’re looking to upgrade to a serious, competition-grade optic, here is your chance to grab a March scope at up to 30% off.
6. Midway USA — Magnetospeed V3 Chronograph, $339.99
All serious shooters need a modern, reliable chronograph to determine load velocity (and consistency). You need good velocity data for your ballistics AND to evaluate the consistency of your hand-loads. The Magnetospeed V3 Chronograph is one of the best on the market. Now you can get this fine Chrono for just $339.99, marked down from $380.00, a $40 savings. We like Magnetospeed chronos because you never need to go downrange to set up tripods and screens. Data can be downloaded to your mobile device.
7. Sportsman’s Guide — Bullseye Blowout Sale (60% OFF)
This week Sportsman’s Guide is offering a Spring Cleaning Bullseye Blowout Sale. There are 72 Bullseye Deals — Gun Cases, Ammo, Hunting Clothing, Archery Gear, Tree Stands, and more. Three gun storage sale items are shown above. NOTE — the biggest savings (up to 60%) are for Sportsman’s Guide Club members. If you’re not a member you can sign up for a 30-Day FREE Trial and still qualify for savings.
8. Amazon — MTM AC4C Ammo Crate with 4 Ammo Boxes, $22.99
Here’s a very cool product from MTM at a great price. The versatile MTM AC4C Ammo Carrier features four, lockable polymer ammo cans in a fitted, four-slot 23.5″ x 11.3″ x 7.5″ carry crate. This makes it easy to haul four full ammo cans. Actual purchasers have raved: “Moments after I received this storage box set I ordered another. Very well built and great design. Awesome and a steal at the price.” Right now this is on sale at Amazon for just $22.99 with free shipping on orders over $25. The system includes four lockable, O-Ring 11.3″ x 7.2″ x 5″ ammo cans (AC30T) for multi-caliber ammo storage. The crate even includes tie-down points for transport in a cart or ATV. NOTE: Last year this MTM AC4C system sold for $39.99. The current $22.99 price represents a 43% savings! Our Deals Editor recently ordered this himself and he liked it so much he immediately ordered another AC4C kit.
9. Amazon — Neiko Digital Calipers, $17.85
Even if you have a good set of calipers, you may want to get one of these Neiko 01407A Digital Calipers. The #1 best-selling digital caliper on Amazon.com, this Neiko tool features a large LCD Screen and measures up to 6.0 inches. With over 3800 customer reviews, this product has earned an overall rating of 4.4 out of 5 stars. It’s hard to go wrong for $17.85, even if you just use these as a spare set for measuring group sizes and case trim lengths.
Share the post "Bargain-Finder 184: AccurateShooter’s Deals of the Week"
Sierra Bullets Ballistician Gary Prisendorf answered: “
Ranges have re-opened in many places, albeit with some social distancing requirements or other health precautions. When you head to the range you’ll want to be prepared. That means collecting all the gear you’ll need at the range. It’s easy to forget small, critical items, so we’ve provided a checklist of the small “extras” you should pack before you head out to the range. In addition to rifle, rests, ammo, targets, and cleaning gear, here are a dozen essentials you should include in your range bag.
• Shell-Holder — If you don’t have calipers, you can use a shell-holder to check for excessive case expansion from hot loads. If a fired case doesn’t slip into the shell-holder easily, your load is definitely TOO HOT.
• Hex Wrench or Screwdriver for action screws — Action screws can work loose with time. Always bring the appropriate hex wrench or screwdriver whenever you go to the range.
• Extra Batteries — Bring extra batteries for all your electronic gear — which can include chronograph, windmeter, digital camera, GPS etc.
• Folding Chair or Camp Stool — This comes in handy if you’re spotting for another shooter, or if you reload away from the firing line.
• Small Plastic Ruler — Use this to measure your group sizes. A transparent (see-through) ruler works best. Rulers are also useful for drawing lines on targets.
• Magnifying Glass – We use a flat, 2″x2″ pocket 4x-8x magnifier. This folds up on itself. Very handy, we use it to inspect bullets and brass. Use this to check your flash holes for burrs, and check the meplats of your bullets before loading.
• Ballistol Aerosol – Try using this versatile lubricant/solvent for full-length sizing. Spray some on a patch and you can wipe the carbon of your case necks. Then, continue to apply a very small amount of Ballistol on the case bodies — just thin sheen is all you need. Ballistol is super slippery, and easy to remove. For general full-length sizing (on small cases) it works great and doesn’t leave a gooey, waxy, or chalky residue. For heavier case-forming jobs, we recommend Imperial Die Wax.
