Over the past 18 months, popular ammo types, such as .223 Rem and 9mm, have been hard to find at reasonable prices. The high cost of .223 Rem centerfire ammo has driven more folks to shooting .22 LR rimfire ammo, both for fun and practice. This Sunday we look at a smart solution that allows you to shoot .22 LR ammo from your existing .223/5.56 AR-15 platform rifle. This is great because it allows low-cost training with no change in rifle balance, ergonomics, and/or optics.
The CMMG Bravo .22 LR Conversion Kit provides a replacement bolt/bolt carrier along with three 25-round magazines with special .22 LR-fitted followers and ammo slots. This allows you to shoot rimfire ammo from any AR-15 chambered for the .223 Rem (5.56×45). The CMMG Bravo has an integrated extension that fits into your current chamber. The rimfire bullet passes through this extension and then enters the barrel.
The CMMG Bravo conversion Kit comes with blowback-operated .22 LR bolt carrier, rubber protector for bolt carrier tip, and three 25-round polymer magazines. To use, simply replace the rifle’s .223 Rem bolt and carrier with the Bravo .22 LR conversion unit and load up the included magazine(s) with rimfire ammo.
To use the CMMG Kit, simply remove the centerfire bolt/bolt carrier, and replace it with the CMMG silver colored bolt shown above. CMMG states: “For best performance use a round-style hammer as notched hammers can cause function issues.” Testers have stated that high-velocity .22 LR ammo works best, and CMMG notes that “36gr plated-nose bullets have proven to be the best choice for function.” The copper-plated bullets help reduce fouling.
Ultimate Reloader Tests CMMG .22 LR Conversion Kit
Our friend Gavin Gear of UltimateReloader.com recently tested the CMMG .22 LR AR Conversion Kit. He observed that installation was very straight-forward and the CMMG magazines worked well. He and fellow tester Travis Fox shot the unit both slow-fire and rapid-fire successfully.
Gavin and Travis found the CMMG Kit easy to install and fun to use. With an AR that can shoot both .223 Rem and .22 LR, it’s like having “two guns in one”. Travis was impressed with the ease of use: “It is so simple to change over to the CMMG .22 LR AR kit! It took me about 68 seconds the very first time I tried. Each time after that it took me about 40 seconds — it’s that simple. It takes longer to fully load one of the mags than it does to switch over from .223/5.56 to .22 LR and back.”
The AR shot very well with the higher-velocity ammo types. 100% functioning was achieved with both 40gr Federal Game Shok ammo and American Eagle High Velocity 38gr Copper-plated HP ammo. NOTE: CMMG does recommend high-velocity Copper-plated rimfire ammunition.
Maintenance Tip — After converting back to your centerfire .223 Rem (5.56), Travis says “make sure to clean the gas tube and components as .22 LR tends to run dirty”. READ Full Test on UltimateReloader.com.
CMMG Bravo Conversion Kit Gets Thumbs Up from Gavin and Travis
“Does this conversion kit get the Ultimate Reloader stamp of approval? Absolutely! In these times of ammunition/component scarcity this gives options to shooters. Finding bulk .22 LR can sometimes be easier than 223/5.56. This kit gives that option at a great price. Any chance to keep skills up and familiarize new shooters to a platform is a good thing. Basically two rifles for a lot less than another rifle.”
How to Install CMMG Bravo .22 LR Conversion Kit
The Brownells video below shows the installation process step-by-step:
In this instructional video, a Brownells gunsmith demonstrates (step by step) how to install, disassemble, clean, lubricate, and reassemble the CMMG AR-15 .22 LR Conversion Kits. Clear the rifle and make safe before you start the conversion. Separate the upper and lower, remove the standard bolt carrier group. You then install the conversion bolt and connect the upper and lower as normal.
Details of CMMG .22 LR Conversion Kit
“For years I’ve had a CMMG conversion kit. It’s a drop-in system that’s … very reliable and it’s accurate. The [CMMG conversion] has lower recoil [and is] great for training. Even though ammo prices have gone through the roof, .22 LR is still cheaper to shoot than anything else.” — SootchGear
This SootchGear video shows how to install the CMMG Bravo unit. The video also compares the original CMMG .22 LR bolt assembly with the latest integrated CMMG Bravo at 2:00-3:50. The older unit had a brass adapter and separate chamber insert. The host also tests a CMMG-equipped AR with various types of ammo. Watch a rapid-fire sequence starting at 1:48 time-mark.
Field Test with Two ARs — Rapid Fire .22 LR Testing
The video below demonstrates rapid-fire .22 LR performance with two different ARs using CCI Mini-Mag ammo. The CMMG conversion is fast and easy: “In a matter of seconds you go from 5.56 to .22 LR”. Watch rapid-fire at 5:40 with CCI Mini-Mags in red/black rifle. Then the tester shoots a variety of ammo in a .223 Wylde-chambered all-black AR, starting at 9:40. The Mini-Mags worked flawlessly, but there were a couple fail-to-cycle sequences in extreme rapid-fire with cheaper “bulk” ammo. The lesson here is use good quality, high-velocity ammo.
NOTE: This 2018 video shows an earlier CMMG .22 LR conversion bolt that features a brass adapter and separate chamber insert. The current CMMG Kit has unitized bolt without a separate adapter or insert.
Interestingly, the Mini-Mag .22 LR ammo shot fine in the .223 Wylde-chambered AR. However, CMMG cautions: “Since .223 WYLDE is NOT a mil-spec chamber, we cannot guarantee fit or function with our 22LR conversion kits.”
Reviews from CMMG Bravo .22 LR Rimfire Conversion Kit Purchasers:
“Get it. Bought this for my Rock River AR. Bolt system goes in [easily] and fits perfectly. Took it to the range and put over 150 rounds through, only failing to feed/fire two rounds. I most definitely recommend this product to anyone looking to shoot their standard AR-15 .223 rifle on a budget.” — Pew P.
“I got this just yesterday and in two days time I have put a couple thousand rounds through it and no hick-ups. I have no complaints.” — Seth
“Best buy for anyone during this ammo crisis. Ammo is extremely expensive and hard to find. It was a ‘no-brainer’ once I found this kit. Ran 200 rounds to break it in for about $20 and had maybe 3 failures. Accurate up to 50 yards (I haven’t tried further) without optic adjustments.” — Joshua M.
“Purchased one of these in January. Took it to the range shortly after for my daughters to try out. We have three ARs and this thing functioned flawlessly. We practiced swapping out the 5.56 carrier with this back and forth, flawless. Enjoyed it so much now I’m purchasing another one.” — J.B.
“Great product. I bought this due to the high cost of ammo. I wanted to still shoot my AR and this was an alternative. This thing works great… works flawless with different types of .22 LR, from premium CCI to the cheap stuff. I recommend this to anyone thinking about getting one.” — Thom
* You can get also CMMG Conversion Kits from Brownells with one (1) 25rd mag for $219.99, or with three (3) 25rd mags for $249.99. There is also a CMMG kit with three (3) 10-rd mags for $249.99 for areas with capacity restriction.
Share the post "Sunday GunDay: .22 LR Conversion Kit for AR-15 Platform"
Tired of spending $15-$25 for a can of spray lube that doesn’t last that long? For about the same price as a single 10 oz. can you can make your own effective spray lube that should last for multiple seasons and lube thousands of cases quickly and easily.
In the YouTube video embedded below, our friend Gavin Gear of UltimateReloader.com shows how to make your own case lube using simple, inexpensive ingredients. As recommended by the 6.5 Guys, this Liquid Lanolin + Isopropyl Alchohol mix works well and is very cost-effective. You can make a pint of this home-brew Lanolin case lube that will lube thousands of cases — many more than a typical commercial aerosol spray can (that’s mostly compressed air).
Gavin describes the exact mixing process on his Ultimate Reloader website. Gavin says this lube mix is a good complement to the Hornady One-Shot (pistol) and Dillon DCL (rifle) lubes he has used for pistol and rifle reloading sessions. CLICK HERE to read more.
Share the post "Make Your Own Spray-On Case Lube — Save Money"
RCBS has introduced an advanced successor to the ChargeMaster Lite electronic powder scale/dispenser. RCBS calls the new machine the ChargeMaster LINK. This boasts multiple refinements, most notably the ability to control the scale via BlueTooth using an APP on your mobile device. RCBS claims the unit “consistently delivers +/- 0.1-grain accuracy, from 0 to 350 grains[.]” It will be able to run from an external battery, or various voltage AC sources using a CE Approved 4-Country Universal Power Supply.
The ChargeMaster LINK will hold up to 2000 grains of powder, and dispense up to 350 grains per charge. MSRP is $349.95, and we expect “street price” to be around $299.00. RCBS plans to start shipping the end of this month (August 2021).
Our friend Gavin Gear of UltimateReloader.com has done an early “reveal” of the new ChargeMaster LINK. Watch the video below for Gavin’s explanation of this machine’s capabilities and features.
Watch Video to see new RCBS ChargeMaster LINK Features
Gavin plans to do a full-length product review but so far he has been impressed with the ChargeMaster LINK: “This new powder dispenser builds on the RCBS ChargeMaster Lite, adding Bluetooth connectivity, and it works with a free APP that will be available from RCBS.”
ChargeMaster LINK Features
The new RCBS ChargeMaster LINK employs the load cell and electronics of the ChargeMaster Lite. However the newer Link model “advances the powder measuring process with built-in Bluetooth that pairs with updated RCBS APP for a customized, streamlined powder-dispensing.”
Bluetooth Compatible with FREE APP
+/- 0.1 Grain Dispensing Accuracy
2000 Grain Powder Capacity
Quick Warm-Up Period
Ability to run on external battery pack
CE Approved 4-Country Universal Power Supply
16 Segment LCD Touchscreen Display
Overcharge Warning via Flashing screen
Ability to disable audible beeps
User-serviceable infinite lifeshaft seals
Sealed Platen to keep powder out
Optimal dispense tub angle for speed and accuracy
Share the post "New RCBS ChargeMaster LINK Powder Scale/Dispenser"
Tumblers and walnut/corncob media are old school. These days many shooters prefer processing brass rapidly with an ultrasonic cleaning machine. When used with the proper solution, a good ultrasonic cleaning machine can quickly remove remove dust, carbon, oil, and powder residue from your cartridge brass. The ultrasonic process will clean the inside of the cases, and even the primer pockets. Tumbling works well too, but for really dirty brass, ultrasonic cleaning may be a wise choice.
Our friend Gavin Gear recently put an RCBS Ultrasonic cleaning machine through its paces using RCBS Ultrasonic Case Cleaning Solution (RCBS #87058). To provide a real challenge, Gavin used some very dull and greasy milsurp brass: “I bought a huge lot of military once-fired 7.52x51mm brass (fired in a machine gun) that I’ve been slowly prepping for my DPMS LR-308B AR-10 style rifle. Some of this brass was fully prepped (sized/de-primed, trimmed, case mouths chamfered, primer pockets reamed) but it was gunked up with lube and looking dingy.”
UltimateReloader.com Case Cleaning Video (7.5 minutes):
Gavin describes the cleaning exercise step-by-step on UltimateReloader.com. Read Gavin’s Cartridge Cleaning Article to learn how he mixed the solution, activated the heater, and cycled the machine for 30 minutes. As you can see in the video above, the results were impressive. If you have never cleaned brass with ultrasound before, you should definitely watch Gavin’s 7.5-minute video — it provides many useful tips and shows the cleaning operation in progress from start to finish.
Ultra Dry Necks After Ultrasonic Cleaning — Some Suggestions
The Ultrasonic cleaning process gets cartridge brass so “squeaky clean” that increased force may be required to seat your bullets, or they may “grab” as they go in the necks. To reduce bullet-seating effort, you may benefit from adding a little dry case lube inside the case-neck before loading (use a nylon brush). Another trick is adding a teaspoon of Ballistol lube to the cleaning solution. That provides a trace lubricant inside the necks, but does not interfere with powder ignition in any way.
The latest Gen2 RCBS ultrasonic cleaning machine has a large 6.3-quart capacity. That’s nearly 100% larger than the first generation machine in Gavin’s video. The Gen2 machine, $385.49 on Amazon, features a second ceramic heater and transducer to better clean brass cases and firearm parts. The LED is easily programmable, and the timer can be set for up to 30 minutes of cleaning. The original 3.2 quart-capacity RCBS ultrasonic machine, as shown in Gavin’s video, is still available for $180.72 at Midsouth Shooters.
Share the post "Get Brass Ultra-Clean with Ultrasonic Machines"
Gavin Gear, founder of the UltimateReloader.com website, has created a very popular YouTube Channel. Over the past 13 years, Gavin has produced hundreds of videos covering nearly every aspect of reloading, rifle assembly, and gunsmithing. When important new reloading products are released, you’ll often find that the very first, in-depth reviews come from Gavin. He seems to get the new stuff before ANYone else.
And Gavin’s multi-product reviews are legendary, such as his remarkable 14-Press Shootout. That video, in which Gavin set up and operated 14 different single-stage presses, has received over 583,000 views, making it Gavin’s third most popular video of all time. The Single-Stage Shootout video, along with Gavin’s five other most popular videos, are linked below.
Consider this a “Greatest Hits” showcase, with a half-dozen Ultimate Reloader videos that have, collectively, been watched nearly 8.5 million times. We present these videos in descending order of total YouTube views, leading with Gavin’s epic .223 Rem vs. 5.56 video, which has been watched over 5 million times.
.223 Rem vs. 5.56x45mm — 6.3 Million Views
Full Story:https://bit.ly/2neNXAS
This video explains essential facts and corrects common misconceptions related to both .223/5.56 ammunition, as well as .223/5.56 rifles. Gavin provides insight on chamber specs, pressure levels, barrel twist rates, military 5.56 crimped brass, and other important topics. If you are new to the AR world, this video is definitely worth watching. And that’s why it now has garnered over 6.3 MILLION YouTube views, making it one of the most popular gun-related videos ever. Gavin adds: “Don’t forget to check out the full write-up on UltimateReloader.com.”
Lee Loadmaster loading .45 ACP — 1.08 Million Views
The .45 ACP is a classic cartridge, and one of the best for a starting reloader. The case diameter is large enough that you can see the case fill level easily. Also you can pick a powder that won’t allow a mistaken double charge (the case will overflow). In this video, from Gavin’s early days on YouTube, Gavin shows how to run a Lee Loadmaster progressive. Lee should be paying Gavin royalties, as this video have been watched over 1 million times.
AR Handguard Upgrade Step-by-Step — 870,000 Views
The AR15 is truly “America’s rifle”. Along with buttstock replacement, one of the most common upgrades done by AR owners is changing out the front handguard. In this video, Gavin shows how to replace your stock handguard with a modern free-floating system. There can be accuracy improvements with this upgrade, and this also allows you to optimize the ergonomics and weight balance of your black rifle.
Full Story:https://bit.ly/2WS9jE0
This truly may be the “ultimate” reloading press video. Running a full 41 minutes in length, this video shows the features/operation of no less than fourteen (14) modern single-stage presses. No other reloading gear review even come closes to this video in terms of the variety of products covered and the sophistication of the tests. In his full story, Gavin offers comparison charts with sizing force and seating precision comparisons. He also measures ram to press frame fit.
Anyone considering purchasing a single-stage press should watch this video from start to finish. A typical gun magazine review might look at two or three presses, load a few rounds, and then offer some subjective comments. Gavin studied 14 presses, did very thorough testing, and delivered tons of objective data. Listed below are 13 of the presses tested. Click each press name for specific details and test results:
Lee Loadmaster Loading .223 Rem/5.56 NATO — 526,000 Views
Here’s another early video from the Ultimate Reloader YouTube Channel. Gavin shows how to produce .223 Rem/5.56x45mm ammo with an affordable Lee Loadmaster progressive. Gavin explains how to set up the Loadmaster and how to best control priming, case sizing, and powder-dropping operations. For anyone thinking about getting a progressive press, this video is worth watching. Gavin has created many other videos reviewing progressive presses from Dillon, Hornady, and RCBS. And just last year he showcased the amazing Mark 7 Apex 10, a ten-station progressive press marketed by Lyman. Gavin’s Mark 7 Apex 10 was equipped with both case-feeder and bullet feeder, allowing very impressive production rates.
How It’s Made: BAT Custom Rifle Actions — 489,000 Views
Full Story:https://bit.ly/3hD2d11 BAT Machine Co. makes some of the finest custom actions you can buy. Numerous national and world records have been set with BAT actions. To create this 31-minute video, Gavin traveled to Idaho to visit the BAT Machine production center in Post Falls, ID. Gavin talked with BAT’s founder Bruce Thom. The video features extensive footage of advanced CNC machines used to produce the superb BAT actions.
Click Image Below to Visit the Ultimate Reloader YouTube Channel:
Share the post "Gavin’s Greatest Hits — Ultimate Reloader Video Showcase"
When you make a reloading mistake, you may need to “pull down” assembled ammo. The embedded UltimateReloader.com video demonstrates how to use the Hornady Cam-Lock bullet pulling system.
When Reloading Goes Bad — The Danger of Over-Charging
Our friend Gavin Gear of UltimateReloader.com was recently reloading some 9mm pistol ammo with his Hornady progressive press. As part of his reloading procedure, he visually checks the cases — and he noticed that the charges seemed high. Sure enough, his most recently-produced rounds were about two grains over spec. He diagnosed the issue: “I was using a powder measure without a baffle. What happened was, over the course of the loading session, things settled in, and the charge level increased.”
Not knowing just when his powder measure started delivering too much powder, Gavin decided, for safety’s sake, to pull down all the ammo he had just reloaded. Yes that’s time-consuming, but it’s better than the alternative — having a dangerous Kaboom while shooting. With fast-burning pistol powders, a two-grain over-charge could cause a blown case, damaged firearm, and/or serious injury.
Watch Cam-Lock Bullet Puller Used to Remove Bullets from Loaded Ammo:
Use of Bullet Puller starts 4:00 minutes into video.
Gavin says it is vitally important to perform safety checks during the reloading process: “You’ve got to do it — check every single round to make sure there IS powder, and that there’s not too MUCH powder. Double, Triple, Quadruple check your components… and your powder charges. You can’t be too careful.”
To pull down a loaded round, first place the cartridge in the shellholder on your press ram. Then raise the round up into the bullet puller device installed where a die would go. The Hornady Cam-lock bullet puller works by clamping the bullet in a collet when you flip down the red-coated lever. Then, with the case held by the rim in the shell-holder, the bullet exits the cartridge as the press ram is lowered. It takes time, but it’s pretty fool-proof once you get the hang of it. This entire process is illustrated in Gavin’s video, starting near the four-minute mark.
The Hornady Cam Lock Bullet Puller has four (4) key components: 1. Cam-Lock die body; 2. Cam-Lock lever; 3. Stem; and 4. Collet (Caliber-specific).
NOTE: In order to use this tool, you’ll need the appropriate collet for each diameter range of bullets you intend to pull. For example use collet #3 for 6mm, collect #6 for 7mm, and collet #7 for .308 Caliber.
RCBS Lock-Out Die
A good safety option for users with progressive presses is the RCBS Lock-Out Die. This has a charge detection rod that dips into each case after powder has dropped. You adjust the die to the proper charge height for your desired load. If the actual dispensed charge is too high or too low, the Lock-Out Die senses the problem and stops the press from advancing to the next case (it does this by preventing the ram/shellplate from fully elevating). We’ve used the Lock-out die with success for both pistol and rifle cartridges. It’s sensitive to about one-half grain with pistol powders.
This Lock-Out Die works with Hornady and Dillon progressives as well as with RCBS progressives. It does take up one die station on the press.
Share the post "How to Use a Collet-Type Bullet Puller"
If you need a heavy-duty, single-stage reloading press, definitely look at the MEC Marksman, a beefy black single-stage unit with many impressive features. MEC, noted for its shotshell reloading machines, now offers the cast-iron MEC Marksman press, offering many features we really like. First, the rugged, cast-iron frame is strong enough for the toughest reloading jobs. Second, the Marksman features an OPEN front — that smart design makes it easier to insert and remove cartridge cases. It also makes it much easier to place your bullets during the seating stage.
This open-front design makes good sense — note that Hornady’s LNL single-stage press also has an open-front layout. Importantly, the MEC Marksman has an innovative, self-centering shell-holder. This patented design should help hand-loaders reload more efficiently.
We were impressed when we first saw the MEC Marksman press. The Marksman combines a sturdy cast-iron frame with a smart, user-friendly open-front design. With a $255.00 MSRP it is more expensive than an RCBS Rock Chucker ($214.16 MSRP), but the MEC Marksman offers some distinct advantages — such as the open front plus the patented floating shell-holder system.
MEC Marksman Press Review by Ultimate Reloader
Our friend Gavin Gear got his hands on a MEC Marksman press and put it through its paces. He came away impressed with the product, saying it delivers excellent performance, and has many impressive features. Gavin tells us: “Cast iron tools and machines are a lifetime investment. The made-in-USA MEC Marksman features ductile cast-iron construction, an open-front frame design for easy cartridge access, a new floating shell-holder design with a unique retention system, and ambidextrous handle setup.”
Gavin liked the Marksman’s system for holding spent primers. A tray sits behind the ram to catch spent primers exiting from a hole near the bottom of the ram. This is more foolproof than the plastic primer cups on some other single-stage presses. Expect less spent primer “spillage”.
The Marksman is sold as a stand-alone unit. However MEC also offers a very nice steel mount/riser for the Marksman. Gavin tested the Marksman with this riser, and he says it was sturdy and well-built. Gavin liked the riser. He said that elevating the Markman press up above the benchtop made it easier to handle cases and to operate the handle. You also get extra left- and right-side die-holders.
Manufacturer’s Product description: The MEC Marksman® is made from ductile cast iron for superior quality and durability. Our patented shell holder self-centers each cartridge. The MEC Marksman® is compatible with all 7/8-14 thread dies to change calibers quickly. Reloading .22 Hornet to .416 Rigby can all be done with one convenient machine.
Share the post "MEC Marksman Press Product Review with Videos"
When is a single-stage reloading press worth close to a thousand bucks? When it’s made in Germany with CNC technology and crafted to aero-space precision standards. UltimateReloader.com’s Gavin Gear recently got his hands on a Turban 120mm Heavy Präzipress. This unit retails for about 715 Euros (714,27 €), which is $858.88 U.S. Dollars at current exchange rates*. Gavin put the Präzipress through its paces, and came away VERY impressed. READ FULL REVIEW HERE.
Impressive Test Results
Sizing once-fired 6.5mm Creedmoor cases with the Präzipress, Gavin achieved great results for shoulder “bump” consistency. The sizing results were nothing short of spectacular. After zeroing the first of ten cases, the remaining nine were essentially identical, showing as “0.000”, meaning less than half a thousandth of variation.
The Präzipress also delivered ultra-low run-out when seating bullets using a Forster die. On all ten test cases, the run-out was +/- 0.001″ (one-thousandth) or less.
Is this kind of press worth the money? Gavin says “yes” if you demand the highest level of precision in sizing and seating: “When you use this press, it’s immediately clear that there are no details neglected, and I can’t imagine one of these presses ever wearing out. Based on the precision tests I did with ammunition loading, it’s clear that this level of precision DOES make a difference for ammunition dimensions and consistency.”
According to Gavin, the “Heavy” 120mm version of the Präzipress is massive and boasts many notable design features:
— Three guide rods with linear roller guides (I have not seen these on any other press)
— Ambidextrous operation (handle can be mounted on left or right side)
— Positive snap shellholder retainer (secure, but easy to insert/remove shellholder)
— 120mm opening accepts cartridges up to .408 CheyTac Size length
— Enclosed spent primer catch system which contains debris
— Optimized leverage (VERY powerful mechanical advantage for sizing)
— Oversized handle (bar diameter) that minimizes flex
There are now three (3) triple-column Präzipress sizes. Along with the 120 model press featured above, there are even larger 140 and 150 models:
* Stated price does NOT include shipping to USA and other fees. The Turban-shop.de website states: “In the case of delivering to a non-EU country, there can be charged extra tolls, taxes, and fees. Packaging costs will be charged separately.”
Share the post "Präzipress 120mm Heavy Reloading Press — German Precision"
With the high cost and reduced availability of factory ammo, more shooters are loading their own ammo. When good 9mm pistol ammo was $10/box, it might be hard to justify handloading. Now that 50 rounds of 9mm can run $40 or more it certainly makes sense to reload. The same is true with rifle ammo if you shoot large quantities, or if you simply can’t find your preferred ammo for sale these days.
To increase productivity when reloading large quantities of ammunition, many shooters are thinking of getting a progressive press. Because multiple operations take place with a single pull of a lever, a progressive press can produce way more ammo in a given period of time than any single stage press. With a progressive, on the ram up-stroke, the multiple stations can simultaneously remove spent primer, full-length size case, drop powder, seat bullet, and crimp (if desired). Most progressives are also set up to prime cases with the ram in the lower position — though some guys prefer to prime manually.
Progressive presses aren’t just for high-output pistol ammo or bulk rifle ammunition. Good progressives can be adapted to do certain reloading tasks for top-on-the line match ammo. You might use a progressive for decapping, priming, and sizing, then throw powder and/or seat bullets separately. Some Champion shooters do use progressives to load their match ammo! For example 5-Time National Long Range Champion John Whidden and 2020 Berger SWN F-Open Champion Jay Christopherson both use progessive presses for some (but not all) operations.
To help you get started with progressive presses, here are five videos from UltimateReloader.com that cover six popular machines, from the elite Mark 7 Evolution to the affordable Lee Loadmaster. With many of these machines you can add separate vertical bullet feeder systems that further increase loading efficiency.
Mark 7 Evolution Press — Distributed by Lyman
Dillon XL-650 vs. Dillon XL-750
RCBS Pro Chucker 7 with Bullet Feeder
Dillon 550C with 6mm Creedmoor and 9x19mm
Hornady Lock-N-Load AP Progressive
Lee Loadmaster Features and Loading 9mm
Share the post "Progressive Presses — Six High Output Progressives Reviewed"
Area 419 has just introduced the all-new ZERO reloading press, a 9-station turret press with some very unique features. This press was designed to be the most precise turret ever created. As tested by Gavin Gear of UltimateReloader.com, the new ZERO turret press delivered very impressive shoulder-bump consistency and ultra-low seated bullet run-out (about +/- 0.0005″). The numbers were as good as you can get from a quality single-stage press, so Area 419 did some impressive engineering. We would expect that, as this is an expensive product — MSRP is $1200.00. SEE FULL REVIEW on UltimateReloader.com.
The ZERO turret press lets you install up to nine (9) different reloading dies in the large top turret, which revolves around a central axis. But unlike most turret presses, the ZERO doesn’t have flex or wobble when you’re loading. This is because Area 419 includes a clever system for locking the turret in position after you’ve selected the die from your array. Area 419 also uses a unique system for securing shell-holders (see video at 12:00). This, likewise, adds to the precision of the press.
In the video above, you can see how the turret is secured with a “wedge clamp”. By loosening the wedge clamp you can index the press easily to any station. Then, when you have selected your die, you tighten the wedge clamp again. You can see this important procedure at 13:20 – 13:35 timemark in the video.
ZERO Turret Press Has Very Smooth Operation
Gavin observed that this ZERO turret is both smooth and very precise, thanks to smart engineering and the use of multiple bearings. Area 419 describes the design features:
— Turret (zero-slop) eliminates variability induced when removing and resetting dies
— The turret head holds nine 7/8×14-threaded dies (1-1/4 thread in future)
— Available ram-stroke here is 4.4″, allowing use of very tall cartridge types.
— Adjustable/interchangeable handle setup for maximizing leverage/feel based on operation
— Internally contained primer-catch system, slide-out drawer
Important Features of ZERO Turret Press
1. Press frame: 6061 Aluminum, clear anodized
2. Wedge clamp (locks turret into indexed position)
3. Turret (7075 aluminum and steel construction)
4. Adjustable handle with roller knob (set either left- or right-handed operation)
5. Bearings: Ball bearing plus roller thrust bearings for side plates
6. Ram riding in self-lubricated linear bearing
7. Spent primer catcher drawer
Milled from American billet aluminum and stainless steel, this press employs 14 bearings, including a self-lubricating linear sleeve bearing for the precision-ground 1.25″ ram. The linkage system also glides on bearings providing smooth operation with near-ZERO slop. The oversized ram features a 0.75″-diameter steel arm and ZERO-friction knob. The turret system is located with an oversized ball-detent system and secured using an over-sized, custom-made ZERO-point pull-stud. Locking the turret after indexing require only a half-turn of the supplied T-handle (see photo above). When indexing the turret, repeatability variance of the system should be less than .0005″.
The opening in the press will allow for sizing and seating of cases up to.338 Lapua Magnum, and will accept standard 7/8″ dies and standard shellholders. NOTE: Area 419 will be making and selling shellholders specifically fit to the system later in 2020.
SUMMARY — Impressive Press Delivers Precise Results
Gavin Gear was very impressed with Area 419’s new Zero Press, which he said offers the precision of a quality single-stage with the versatility of a turret: “There will always be people that prefer a traditional single-stage. Where the ZERO will be compelling is to those who want the precision of a single-stage without the need to screw dies in and out. Leaving your dies set can have benefits for precision as well — everything comes back to the ‘same place’ when dies are indexed into position. Screwing dies in and out can impose variation, and variation is the enemy of the ‘white lab coat shooter’. I plan on testing the ZERO press with ultra-high-end dies, and custom dies that I ream to my own specifications. I’m thinking that will show the true potential of this press!”
Area 419 ZERO Press Video with Operation Instructions
Share the post "Advanced New Area 419 ZERO 9-Station Turret Press"
Every serious competitor needs a good spotting scope support. Spotting scopes are not just for iron sights shooters. Even if you have a powerful riflescope, the spotting scope, typically set at 15-25X magnification, lets you observe wind flags, mirage, and other shooters’ targets. If you are looking for a high-quality, made-in-USA support for your spotter, consider the Polecat V2 system from Creedmoor Sports. Our friend Gavin Gear of UltimateReloader.com recently posted this video review:
Creedmoor Sports has offered excellent products for competitive shooters for decades. The Made-in-USA Polecat V2 system is updated version of Creedmoor’s best-selling spotting scope stand. After collecting feedback from shooters across many disciplines for several years, the designers brought some major advances to this scope stand. First, no pretension are adjustments needed. Horizontal and vertical resistance is controlled by the knurled tightening knob. Second, the Polecat boasts a pre-aligned Delrin clamp so you don’t have to spin the clamp to align with the rods during stand assembly. You can order a Polecat V2 with 3/4″-diameter rod for $296.95 or get the 1″-diameter rod version for $364.95.
Either version can be used for both left-handed and right-handed shooters, with about 5″ standoff from the center of the stand to the scope’s centerline. Polecat V2 packages include head, stop collar, one extension rod, and base. Additional aluminum rods are available to extend height.
Polecat V2 Key Features
— Adjustable head (spotting scope mounts to head)
— Bump stop (protects spotting scope from accidental knock if dropped)
— Base with three fold-out legs
— Leveling adjustment for uneven ground (one leg can be adjusted downward, faced in downhill direction)
— Zero play (slop), giving you the ability to quickly and easily make adjustments
— One-handed operation/adjustment
— 1/4″-20 standard spotting scope thread
— The scope may be positioned above or below the scope head
Factory-loaded ammunition has become very hard to find, particularly pistol ammo. Concerns over social unrest, personal security, and the upcoming election have spiked demand for loaded ammo. Everyone is asking “where has all the ammo gone?”
Pistol Ammo Hard to Find
In particular, 9mm pistol ammo flies off the shelves as soon as it arrives, and even major online vendors such as Midsouth Shooters, MidwayUSA, and Natchez have very limited supplies.
Need Ammo? Load Your Own…
One answer to the ammo shortage is to load your own. And if you want to produce a large quantity of ammo in a short amount of time, the progressive press is the answer. There are many progressive press systems, from modest Lee progressives to high-end, automated systems from Mark 7 (Lyman). In this article we feature the “latest and greatest” progressive press from Dillon — the new eight-station RL 1100 Press with Case-Feeder.
Our friend Gavin Gear of UltimateReloader.com got his hands on Dillon’s impressive new RL 1100. In two videos, Gavin shows how to set up the RL 1100 and then he demonstrates how to produce 9mm pistol ammo with this impressive 8-station press.
Gavin says: “My Dillon RL-1100 is cranking out the 9mm, and in this video we bring it up to ‘full tilt’ speed” [with the MR. Bullet Feeder and the Dillon Case-Feeder]. If you watch the video, you’ll see Gavin produce 9mm ammo at a rate of nearly 50 rounds per MINUTE!
Gavin equipped his new RL 1100 with two cool products from Double Alpha Academy (DAA) — the Mr.Bulletfeeder® as well as an advanced, Magnetic Powder Check. When loading ammo you can never be too safe, so we definitely recommend the use of powder-check dies (we use a conventional RCBS powder-check die on our progressives). The DAA bullet feeding system is an important add-on that significantly increases output rates when used in concert with the Dillon Case-Feeder (blue funnel).
RL 1100 Reloading Stations with Powder Check and Bullet Feeder
RL 1100 Stations shown above:
1. Case inserter
2. Sizer/De-Primer
3. Swager (with hold-down)
4. Priming (no die)
5. Powder charge and expansion (expansion for pistol cartridges only)
6. Double Alpha Magnetic Powder Check
7. Mr. Bullet Feeder bullet feed die
8. Bullet seating and Crimping
Note: In order to accommodate the magnetic powder check die AND the bullet feed die, bullet seating and crimping were combined at the last station.
The RL 1100 has some very impressive features that allow faster and easier ammo production. An Eccentric Roller Bearing Drive System reduces friction. The RL 1100’s heavier frame provides greater rigidity for more efficient cranking. The RL 1100 also boasts an improved shellplate indexing system. Priming is enhanced through a spring-loaded Priming Station Locator and Upgraded Primer Pocket Swager.
Dillon RL-1100 Set-Up Video:
Loading with the “Turbocharged” Dillon RL-1100
Gavin was very impressed with his RL-1100: “This reloading setup is [great]. Every crank of the lever yields a completed cartridge, and the attainable speeds are AMAZING. The case feeder and bullet feeder had no trouble keeping up with my quick pace using this setup. And it is great to know that every powder charge is being checked.
This press is very reliable and smooth, bridging the gap between lower cost home set-ups and six-figure commercial loading equipment packages. What’s next? I’ll be performing a caliber changeover to .308 Winchester.”
The DAA Magnetic Powder Check can be used on a variety of Progressive Presses.
Share the post "Powerful Progressive — Dillon RL-1100 with 8 Stations"
RCBS Lock-Out Die
If you need a heavy-duty, single-stage reloading press, definitely look at the MEC Marksman, a beefy black single-stage unit with many impressive features. MEC, noted for its shotshell reloading machines, now offers the cast-iron 
Impressive Test Results
Pistol Ammo Hard to Find
