Sierra Bullets has recently released load data for the 6mm Creedmoor cartridge, a necked-down version of the 6.5 Creedmoor, a popular PRS, tactical, and hunting cartridge. Sierra has released very comprehensive 6mm Creedmoor load data, covering fifteen (15) different bullets from 55 to 110 grains. NOTE: Hornady-brand brass was used for Sierra’s 6mm Creedmoor load tests, not the newer, stronger Lapua 6.5 CM brass with small primer pockets. Hand-loaders using Lapua 6.5 Creedmoor brass necked to 6mm may have to adjust their loads.
Sierra writes: “As soon as the 6.5 Creedmoor was released in 2007, a 6mm version was being envisioned. After the 6mm Creedmoor demonstrated its worth at 1000 yards it began to catch the attention of Precision Rifle Series (PRS) competitors. The 6mm/6.5 Creedmoor is a great fit for those looking for an AR platform-friendly cartridge. It delivers velocities very similar to the .243 Win and yet fits the AR10 magazine length[.] The 30-degree shoulder makes this a very efficient case and helps prolong case life as well. The 6mm/6.5 Creedmoor works well with powders such as H4350, RE-17, and Ramshot Hunter for heavier long-range bullet weights. Slightly faster powders such as RE-15, Win 760, and Vihtavuori N540 work well with lighter weight bullets.”
Sierra Bullets Tested for 6mm Creedmoor Load Data
55gr BlitzKing (#1502)
60gr HP (#1500)
70gr HPBT (#1505)
70gr BlitzKing (#1507)
75gr HP (#1510)
In developing its 6mm Creedmoor load data, Sierra tested a very wide selection of propellants, two dozen overall. For the smaller bullets, fast-burning powders such as Benchmark, H4895, and CFE223 were tested. For the heavier 100+ grain bullets, Sierra tested a selection of medium-burn-rate powders including H4350, Reloder 16, Reloder 17, Varget, and Superformance. Sierra did a very thorough job. We know this information will be welcomed by 6mm Creedmoor shooters.
Don’t know what powder to try first? For the 107-110 grain bullets, if you want best accuracy and low ES/SD, our Forum members recommend Alliant Reloder 16 and Hodgdon H4350. If you are seeking max velocity with the 110-grainer, look at Hodgdon Superformance and Reloder 19.
Here are Sierra’s 6mm Creedmoor Load Data Charts for the 107gr MK and 110gr MK. There are a half-dozen other tables for lighter-weight bullets.
Share the post "6mm Creedmoor Reloading Data From Sierra Bullets"
Dave Emary is concluding his 24-year career at Hornady. Although retiring from full-time duties, Emary will continue with Hornady as a consultant. AccurateShooter.com wants to acknowledge Dave’s decades of important work in the gun industry. Brilliant, dedicated, and forward-thinking, Dave has been one of the top minds in our industry for many years. He will be missed. He can claim credit for many of the most important innovations in cartridge and bullet design in recent decades.
Ask Dave Emary what he liked best about his job as senior ballistics scientist at Hornady, and he’d tell you that it was finding better ways to do things. “At the heart of me, I’m a tinkerer,” Emary said.
To borrow an expression from aeronautics, this Air Force veteran is inclined to “push the envelope,” to think outside the box. “I’m not one willing to just go with the status quo,” Emary said.
Over his 24-year tenure with the company, Emary helped accomplish some of the biggest breakthroughs at Hornady. Although Emary said he was merely in the right place at the right time, the list of projects he influenced in one way or another is a long one.
Dave Emary the Innovator
Fans of Hornady products will quickly recognize the names of ammunition lines such as Critical Defense®, Precision Hunter™ and LEVERevolution®, or cartridges like the 6.5 Creedmoor and 17 HMR, but those are just a few of the dozens Emary worked on after being hired as bullet/ammo lab manager in 1994. For his groundbreaking work, Emary was honored as one of Outdoor Life’s Top 25 for Innovation in 2007.
Emary came by his interest in ballistics naturally, growing up on a farm near Wakeman, Ohio, where he began shooting when he was 10 years old. His dad had a .22, and he shot a lot of small game, rocks and other targets of opportunity.
In this 2008 video, Dave Emary talks about the “new” 6.5 Creedmoor cartridge.
Father And Son at the Vintage Sniper Match
Dave Emary was a key figure in starting the CMP’s Vintage Sniper Rifle Match. Dave was instrumental in bringing the new match to fruition and he says his father was his inspiration. Below, Dave Emary and his father Robert reflect on the success of the first Vintage Sniper Rifle Team Match held at Camp Perry.
Robert Emary (above right) was a decorated World War II scout sniper who parachuted into Holland after the Normandy Invasion and fought all the way to the Eagle’s Nest. (Photo: CMP The First Shot)
Dave Emary was a competitive shooter. This photo shows Dave (left) and “Gunny” R. Lee Ermey (right) shooting the Vintage Sniper Team Match at Camp Perry. (Photo: NRA Blog)
Q and A with Dave Emary
There is an interesting interview with Dave Emary on the Hornady Blog. Dave shares some insider knowledge on how new cartridge types are developed and SAAMI/CIP standardized. And Dave also comments on his favorite new and old cartridges:
Q: Which Hornady rounds have you helped design?
A: This list gets pretty long, Light and Heavy Magnum, A-MAX Match bullets, V-MAX bullets and the Varmint Express line, 450 Marlin, 17 HMR, 204 Ruger, 17 M2, LEVERevolution bullets and ammunition, 308 and 338 Marlin Express, Ruger Compact Magnums, Critical Defense bullets and ammunition line, 6.5 Creedmoor, Critical DUTY bullets and ammunition, Superformance propellants and ammunition. There’s probably some I’ve forgotten.
Q: What is your personal favorite caliber and why?
A: I love the 6.5 Creedmoor. It provides exceptional accuracy along with being very easy and comfortable to shoot. The external and terminal performance offered by 6.5 mm bullets for the ease of shooting is unmatched. At this point in time it is the only bolt action hunting rifle I own. I occasionally pick it up rather than my lever guns to go hunting. It almost seems unfair hunting with it because of how accurate and flat it shoots and how effective it is.
Q: Which historic calibers do you admire and which is the greatest in your view?
A: It’s hard to look past the .303 British and 8×57 because of their tremendous historic significance. I would also rate the .30–06 in with the previous two. The other cartridge I think really started the present day commercial sporting ammunition designs is the 30–30 Winchester. It was one of the first high velocity, smokeless, commercial offerings and lead the way for cartridge development that eventually far eclipsed it.
Dave Emary’s Background — Physics, Astronomy, Air Force Service, and Ballistics
After earning his Bachelor of Science in physics from Bowling Green State University, Dave worked for a year at the National Radio Astronomy Observatory’s Karl G. Jansky Very Large Array in New Mexico before joining the U.S. Air Force. In the Air Force, he earned a second bachelor’s degree, in aeronautical/astronomical engineering. He served for six years, rising to the rank of captain.
After the Air Force, Emary worked at the New Mexico Institute of Mining and Technology’s Energetic Materials Research and Testing Center (EMRTC), the largest ordnance-testing facility in the U.S. outside the government. “That’s where I really got into the ballistics side of things,” Emary said. Among other things, research by Emary and his colleagues led to the development of the electromagnetic railguns now being used by the U.S. Navy that launch projectiles at 4,500 mph.
From there, he went to work for St. Marks Powder in Florida, the nation’s largest gun propellant producer. There, his work caught the attention of Steve Hornady, who offered Emary a job. “Dave had built a reputation as an innovative thinker and problem solver, and I wanted those qualities for our team,” Hornady said.
Dave Emary Returns to EMRTC as Engineering Director
Although he has retired from Hornady, Dave Emary will still use his skill set and vast ballistics knowledge in a new job at a familiar place — as Director of Engineering at the Energetic Materials Research and Testing Center. EMRTC is internationally recognized in explosives research and testing. For Emary, it’s just his way of easing into retirement.
“I feel incredibly blessed to have been able to be a member of this industry, Hornady Manufacturing and to have been afforded the opportunities I have been given,” Emary said. “I thank the Lord every day for the success I have had, which has been enormously aided by many other people.” — Dave Emary
Share the post "Dave Emary Retires as Hornady Senior Ballistician"
With its 2018 product roll-out, Hornady has introduced two new reloading products that look promising. There is a new modular, vibratory powder trickler, plus a new rotary tumbler for wet-tumbling brass.
New Cordless Vibratory Powder Trickler:
Hornady’s new modular Vibratory Trickler, powered by two AAA batteries, features variable settings to trickle all kinds of powders. The clever modular design allow you to separate the actual trickler dispensing unit from the base (a cord connects base to trickler). That lets you position the trickler next to your scale with the separate control unit convenient to your hand. This also makes cleanup more easy.
Product Features:
Trickles all powders
Light-up LED screen
High, low, and variable trickle settings
Use in base or outside of base
No-slip base, weighted for stability
New Hornady Rotary Case Tumbler
Hornady’s new, large-capacity rotary tumbler can be used to wet-tumble cartridge brass. This will clean and polish brass inside and out quickly when used with the included steel pin tumbling media. The large, six-liter drum holds five pounds of brass cases. Set tumbler to run for up to eight hours in half-hour increments using the digital timer. This new rotary tumbler is designed to be used with Hornady One Shot Sonic Clean Solution.
Note: we do recommend you test with your brass to ensure the steel pin media does not jam in flash holes. And always inspect each case after the tumbling cycle.
Hornady has introduced a new Short Magnum cartridge, the 6.5 PRC (Precision Rifle Cartridge). This will be offered as factory ammo in both a “Match” version (with 147gr ELD) and a “Precision Hunter” version (with 143gr ELD-X bullet). Presumably, in the future, Hornady will offer 6.5 PRC brass separately for hand-loaders, but Hornady has no time-line for brass availability. However, you can get 6.5 PRC brass right now from GA Precision at $86.00 per 100 cases. GA Precision’s George Gardner, who helped develop this cartridge, has posted: “It’s a non-rebated short mag based on a short RCM [Ruger Compact Magnum] case. It has 3-4 grains less capacity than the 6.5 SAUM which nets about 30-50 fps deficit to the SAUM.”
The 6.5 PRC Match seems to be aimed at the PRS crowd and long-range tactical shooters. The product launch photo shows a tactical rifle and steel plate. Hornady says the 6.5 PRC was “designed to achieve the highest levels of accuracy, flat trajectory, and extended range performance in a sensibly-designed compact package. Utilizing moderate powder charges that result in repeatable accuracy, low recoil, and reasonable barrel life, the 6.5 PRC produces high velocities for target shooting with performance well beyond 1000 yards.”
“High Velocities”? Wait a minute — here’s the ballistics chart from Hornady’s 6.5 PRC page. It shows a muzzle velocity of 2910 FPS. That’s not much better than a 6.5 Creedmoor (which can push 140s over 2800 fps), so we wonder about this. You have to ask — what is the point? Is there anything this 6.5 PRC can do that the venerable 6.5-284 can’t do just as well or better — with a standard bolt face?
New 6.5 PRC Is a Short Magnum Requiring Magnum Bolt Face
Dubbed the “big brother” to the 6.5 Creedmoor, the 6.5 PRC fits in short or medium actions with a standard magnum bolt face (.532”). The case geometry features a long cartridge case neck and 30-degree case shoulder. It sort of looks like a 6.5 Creedmoor on steroids. For its loaded 6.5 PRC Match Ammo, Hornady is showing a 2910 fps Muzzle Velocity with the 147gr ELD Match bullet. That’s not very impressive. Why go to the trouble?
Comment — Does This New 6.5 PRC Cartridge Fill a Need?
Honestly, we don’t get this. If you need more speed than a 6.5 Creedmoor and want to stick with a .264-diameter bullet, then shoot a .260 Rem or 6.5-284 using a standard bolt. This requires a magnum bolt face. The 6.5-284 is a barrel burner; the 6.5 PRC promises to be likewise. On the other hand it may work better than a 6.5-284 in a short-action magazine — that may be what Hornady is thinking…
The 6.5 PRC clearly seems to be targeted at the PRS crowd. But we see many top PRS competitors moving DOWN in cartridge size, rather than up. Many PRS guys have stepped down from the 6.5 Creedmoor to the 6mm Creedmoor, or even a 6mm Dasher. The benefit is less recoil, and cheaper bullets. Are there really many PRS shooters clamoring for a short magnum? We don’t think so.
We’ll see if this new 6.5 PRC cartridge catches on — maybe some PRS guys will want this for long-range side matches. Rifle makers currently chambering the 6.5 PRC include GA Precision, Gunwerks, PROOF Research, Stuteville Precision and Seekins Precision.
6.5 PRC Ammunition for Hunters — Also New for 2018
Hornady will also sell a version of 6.5 PRC ammo design for hunters. The Precision Hunter version, shown below, is loaded with the 143-grain ELD-X Bullet. Again, however, we really don’t know why any hunter would want to shoot this cartridge, when you already have so many good choices, such as the 6.5x55mm Swede, and the original .284 Winchester, both of which can use a standard bolt face.
If you have a hunting rifle with a magnum-size bolt, why not shoot the 7mm RSAUM or 7mm WSM? Barrel life is not really an issue for hunters, so the smaller case capacity of the 6.5 PRC is not really an advantage. Perhaps the veteran hunters among our readers can enlighten us, using the comments section. Would you build a hunting rifle chambered for the 6.5 PRC?
Share the post "New Hornady 6.5 PRC — Precision Rifle Cartridge"
Nobody likes to spend hours manually chamfering cases and cleaning primer pockets. There are simple hand tools that will perform these tasks, but the process is time-consuming and tedious after a couple dozen cases. To speed up case prep duties, you can get one of the large, powered case prep centers. These function well, but frankly we didn’t want to give up that much precious space on our reloading bench. One good solution is Hornady’s compact Case Prep Trio (item 050160). This triple-threat tool packs a lot of functionality in a small package.
This cleverly-designed powered tool has a small footprint, yet it can perform three tasks as well as much more expensive, tower-style case prep units. The Hornady Case Prep Trio is now $85.99 at Midsouth Shooters Supply. We’ve used this machine and it works well. The only negative is that you will get metal shavings on your bench (unlike some of the larger case prep centers). We’ve seen some guys put a small pan under the power head — then you can just dump the shavings out of the pan.
With three active stations, you can chamfer, deburr and clean primer pockets without having to change tools. The Case Prep Trio ships with inside chamfer, outside chamfer, and deburr tools. You can also use the machine with other optional 8/32 threaded accessories such as primer pocket reamers and case neck brushes. Conveniently, the Case Prep Trio has on-board storage for your tool-heads. User reviews have been very positive.
Share the post "Versatile, Affordable, Compact Case Prep Trio Saves Time"
When considering .17-caliber Varminting, most guys think rimfire — shooting the 17 HMR or the newer 17 WSM. But there is a good, affordable centerfire option — the 17 Hornet — with quality factory ammunition available. Hornady produces factory 17 Hornet Ammo with three bullet options: 15.5gr NTX, 20gr V-Max, and the new 25gr HP Varmint. Our friends at Varminter.com recently conducted a test of Hornady’s new 25gr HP “Custom” ammunition, reasonably affordable at around $29/box of 50 rounds. Varminter.com tested the ammo in a CZ 527 rifle chambered for the 17 Hornet on a ground squirrel hunt in Northern Nevada.
Hornady 17 Hornet 25 Grain HP CUSTOM™ Ammo (#83006) Specifications:
25 grain HP Varmint bullet
3375 fps rated (Varminter.com averaged 3383 fps in CZ Model 527 with 24″ barrel)
632 FPE (Foot Pounds of Energy)
0.187 G1 Ballistic Coefficient
Ammo Testing and Hunt Report
By Varminter.com’s Editor
With the new 25gr Hornady 17 Hornet ammo, our accuracy results ranged from 0.528″ to 0.85″, with an average of 0.678″ over ten, 5-shot groups at 100 yards. After shooting the groups, we settled on a 200-yard zero, which put the rifle at 1.1″ high @ 100 yards and 5.3″ low @300 yards.
“I went 14 shots in a row without a miss, and that was from 80 yards out to 220 yards. On these small varmints here, the 25-grain HP does a good job [and] the ammunition is accurate.”
Ground Squirrel Gauntlet in Northern Nevada
It was a few months after the initial range work when I was able to really put this ammo to work on some varmints. The grass here in Southern Idaho had grown quite tall, so we decided to head over to a spot on a private ranch down in Northern Nevada. We were promised some good shooting, but until we actually sit down at the bench and start pulling the trigger, we try not to get our hopes up. Needless to say, we were not disappointed in the amount of varmints and shooting we experienced!
The set-up was simple. I set-up with my bench pointed down a private dirt road on the edge of a large alfalfa field. I was going to be shooting something I call “The Gauntlet”. What this means, is that the majority of the ground squirrels were making their home outside of the alfalfa fields. This is a perfect spot for ground squirrels, because they are forced to cross an open area (the dirt road), in order to get to the lush, green, alfalfa. Within this gauntlet, the ground squirrels would consistently stop on the edge to make sure it was safe to run across to the alfalfa side. This gives you a few seconds [time window] to find the squirrel in your scope and make the shot. The range of shoots were from 80 yards out to 220 yards down the road. CLICK HERE to read full 17 Hornet Hunt Report.
Speed Kills — 3650 FPS with a 20-Grainer
Based on the 22 Hornet cartridge case, the 17 Hornet can drive a 20-grain V-MAX bullet at 3,650 fps. At this velocity, the 17 Hornet can match the trajectory of a 55-grain .223 Remington load, but with much less noise and recoil. Look at the chart below. You can see that the 17 Hornet’s trajectory (blue-gray line) is almost an identical match for the larger .223 Rem (red line) all the way out to 400 yards or so.
Share the post "Hunt Report: Squirrel-Busting with Varminter.com’s 17 Hornet"
We have all been there…..you place a piece of tumbled brass in the shell-holder of your press, raise it into the die, and suddenly it is like somebody hit the brakes. The case is stuck in the die. Your first instinct is to reverse it out. You crank on the handle, and BANG! The rim rips off the case head and you are looking at a piece of brass stuck in the die.
A stuck case is one of the boo-boos that all of us reloaders have faced from time to time. If proper lubrication is applied, then it should not be a problem. No matter if you are a seasoned reloader or new to it, this situation can happen. Take your time, use the proper procedures, and you will be back in business in no time! This article explains how to avoid stuck cases (through proper lubrication) and how to use a stuck case removal system.
What Causes Stuck Cases
One of the first common mistakes reloaders face is the stuck case. It can be caused by too much or too little lube. Too much and a vacuum can be formed causing the case to become suctioned into the die. Too little lube and friction is the culprit. So what is the cure? There is no exact cure, but the best lube that we have found so far is just a dab of Imperial Sizing Die Wax on your fingers and applied in a thin coat on the body of the case, not the shoulder or neck. Too much of this wax can cause the vacuum effect, or can eventually load your die up with gobs of residue. If it is applied to the shoulder area, or the leftover wax moves up into the shoulder region of the die, you will see dents or dimples in the shoulder. [AccurateShooter.com Editor’s Note: For normal full-length sizing of small cases such as 220 Russian/PPC, 6mmBR, 6.5 Grendel, or 6.5×47 Lapua we recommend Ballistol (aerosol) lube. It is very slippery, goes on very thin, and does not gum up the die.]
A great way to ensure that your dies are clean is to use a simple chamber mop with a dab of your favorite solvent on it and clean out the die. Be sure all of the solvent is out after cleaning by spraying the die out with Quickscrub III or use a clean chamber mop. If you are storing your dies, you can apply a thin coat of a good oil to protect the steel such as TM oil or Starrett M1 Spray.
Using a Stuck Case Removal Kit
If you do stick a case in your die there are a few good stuck case removal kits available. Each one works in a similar fashion. I have found the Hornady kit very effective and easy to use.
Basically what you do is remove the die from the press. Unscrew the decapping assembly and pull it out as far as you can. You then need to drill/tap threads into the stuck case head (this is why it is suggested to unscrew the decapping assembly as far as you can to get it clear of the drill bits). Once this is done screw the die back into the press. You then install the included shellholder attachment on the shellholder ram, and thread it into the case via a small wrench. With some elbow grease you can reverse the stuck case out of the die with the leverage of the press, and not damage the die.
However if the case is stuck….REALLY stuck, you may pull out the threads on the case and you are still left with a stuck case in the die without any way to pull it out. If the case is really difficult to remove even with the use of a stuck case removal kit, do not try to be Hercules with the press ram. Here is a trick that may work. Take the die with the stuck case and place it in your freezer for a couple of hours. Then repeat the removal with the cold die. The freezing temperatures may cause the brass to contract, and make removal easier. If this does not work it is recommended to send it to the die manufacturer. They will be able to remove the case without damaging the die.
Another fix if you can remove the decapping assembly completely is to use a tap hammer and a punch or small wooden dowel to knock the stuck case out. This isn’t the best way since it is very possible that you will damage the die internally or externally on the threads, or both. Send the die to the manufacturer to have this done properly. You will be happier in the long run.
This upcoming Monday, July 24th, the CMP hosts the Vintage Sniper Rifle Match at Camp Perry. One of the most popular vintage rifle matches held each summer at Perry, this is a two-man team competition using scoped rifles of WWI and WWII Vintage. Many competitors use some version of the M1903 Springfield, but you’ll also see scoped M1 Garands, K31s, Mausers, and even a Lee-Enfield or two.
Two-person teams will fire 10 rounds in 20-second intervals from scoped vintage military rifles set on sand bags. One team marksman shoots from the prone position at 300 and 600 yards, while the other serves as a spotter to relay shot position. Marksman and spotter switch positions on the firing lines, allowing each teammate to play both roles. Scores are then combined for an Aggregate team total.
Two M1 Garands, fitted with scopes and lace-on cheekpads.
Who can identify this rifle, with its unusual scope mount?
Our friends at Criterion Barrels have written an interesting article about last year’s Vintage Sniper Rifle Match. It you want an “insider’s perspective” on the 2014 Match, plus Vintage Sniper gunsmithing tips, read this article. Here are some highlights:
About the Match and the Rifles
The Vintage Sniper Match was the brainchild of Hornady’s Dave Emary. The competition was inspired by his father, a World War II scout sniper, who carried a rifle similar to the 1903A4 rifle builds that can be found today on the Camp Perry firing line. Bob Schanen worked alongside Dave and the CMP staff in establishing the various competition rules prior to the first official Vintage Sniper Match in 2011. The match developers made a point to offer some level of flexibility in rifle configuration, allowing specific types of non-issue optics and rifle rebuilds. This helped make the match more inclusive.
Hornady’s Dave Emary and “Gunny” R. Lee Ermey (right):
Bob Shanen has two vintage sniper competition rifles. Both builds are based off of the USMC Model 1941 sniper rifle, a design similar to the M1903A1 National Match rifle. Bob’s rifles both carry 8x Lyman Junior Target Spotter scopes with a thin crosshair reticle. Bob attributes a large part of his rifle’s accuracy to the Criterion M1903 match-grade barrels installed on each rifle by Rick Humphreys, a Milwaukee area gunsmith. These tack-driving barrels are capable of half-MOA accuracy.
Camp Perry — The Venue
The hallowed grounds of Camp Perry have hosted some of the nation’s finest shooters each summer for more than a century. Some of the world’s greatest marksmen have accomplished remarkable feats on the ranges of this lakeside military outpost. Located on the coast of Lake Erie, Camp Perry is positioned just outside of the scenic town of Port Clinton, Ohio. It is our firm belief that every shooter should make the pilgrimage to the Camp Perry at least once in their lifetime. If not participating in an event, visitors should at least make an attempt to meet the competitors, witness the wide selection of firearms used by participants, and pay a visit to the various vendors on base.
MidwayUSA is running a big sale on Factory Second and Blemished Bullets. These bullets normally perform just as well as regular bullets, but they may have water spots or other cosmetic defects. MidwayUSA has a very large selection of seconds/blem bullets on sale for both rifles and pistols. Here are some of the best deals we found among the quality varmint and match rifle bullets. All these selections are discounted 30%:
At the request of our readers, we provide select “Deals of the Week”. Every Monday morning we offer our Best Bargain selections. Here are some of the best deals on firearms, hardware, reloading components, and shooting accessories. Be aware that sale prices are subject to change, and once clearance inventory is sold, it’s gone for good. You snooze you lose.
1. Monmouth Reloading — Nosler RDF Bullets, $28-$29 per 100
Nosler’s line of RDF (Reduced Drag Factor) bullets have very high BCs for their weight. Precision shooters are reporting outstanding accuracy. Given their high performance and consistency, RDF bullets represent a superior value. At Monmouth Reloading you can get Nosler RDFs for under $29 per 100 for popular 6mm, 6.5 mm, and .30-Cal sizes. That’s up to $20 less per box than some premium brands. Based on user reports, we recommend you start with these pretty far out from the lands. One shooter using the 6.5 mm 140-grainer reports: “This bullet likes to jump. Berger Hybrids liked a jump of about 0.010″ – 0.020″. Once I seated the RDFs to jump 0.045″, my groups shrank to about 0.3 MOA. You cannot beat the price or performance of this bullet!”
2. Amazon.com — Rock Chucker Supreme Reloading Kit, $279.99
Everything you see above can be yours for just $229.99, after manufacturer’s rebate. Right now, Amazon is selling the Rock Chucker Supreme Master Reloading Kit for $279.99. That’s a great deal considering all the hardware you get. Heck, the Rock Chucker press alone is worth $150.00+. But here’s the real incentive — this Rock Chucker Supreme Kit qualifies for a Buck$ or Bullets Rebate — choose either $50 or 500 Speer bullets. If you take the fifty bucks ($50), that reduces your net cost to just $229.00 for the entire RCBS Reloading Kit. That’s a total steal. NOTE: Cabelas.com also sells this RCBS Kit for the same $279.99 (before rebate).
3. Amazon — Neiko Digital Calipers, $16.45
Even if you have a good set of calipers, you may want to get one of these Neiko 01407A Digital Calipers. The #1 best-selling digital caliper on Amazon.com, this Neiko tool features a large LCD Screen and measures up to 6.0 inches. With over 2700 customer reviews, this product has earned an overall rating of 4.4 out of 5 stars. It’s hard to go wrong for $16.45, even if you just use these as a spare set for measuring group sizes and case trim lengths. These are inexpensive but will do the job for basic tasks.
4. Natchez — Surplus SKB 5041 Transport Cases, $129.99
Natchez has obtained a supply of British MOD Surplus SKB 5041 rifle cases. These were ordered as mine detector cases, but were never issued. Natchez has removed the foam cut for the detectors and replaced it with new 2-piece convoluted foam. Interior dimension of the case is 50″x14.5″x5″ so this will hold long-barrel match rifles comfortably. These are extremely high-quality cases, very tough and rugged, waterproof with gaskets. These cases feature four SKB patented trigger latches, four reinforced padlock locations, and inline wheels. Though in excellent condition, some case may have minor exterior scuffs. You won’t find a better case at anywhere near the price. These normally retail for $299.99.
5. Amazon — Lyman Case Prep Xpress $103.99
The Lyman Case Prep Xpress lets you chamfer inside and out, brush your necks, clean/uniform primer pockets, and ream military crimps. On sale at Amazon.com with $103.99 Prime pricing, this is a good deal. Lyman’s Case Prep Xpress sells elsewhere for $130.00 or more. Here is a review from a Verified Purchaser: “The unit is quiet, sturdy, and the attachments do what they are supposed to do. It already has made a difference in my reloading speed, and most importantly, my comfort. I highly recommend this unit.” (Strafer, 4/7/14)
6. Midsouth — Norma Tac-22 .22 LR Ammo, $3.99/box
This Norma .22 LR ammo shoots WAY better than you’d expect given the low price — just $3.99 per 50ct box at Midsouth. These test targets come from Champion Shooters Supply. That vendor reports: “We have found this to run very well in Ruger rifles, handguns, and target pistols. These are 5-shot groups at 50 yards with an Anschutz 1913 rifle. This is an incredible value.” We suggest you grab some of this Tac-22 while you can at these rock-bottom prices.
7. Midsouth — Hornady LnL Auto Charge Scale/Dispenser, $158.99
The Hornady Lock N Load Auto Charge Electronic Scale/Dispenser is now on sale for just $158.99 at Midsouth Shooters Supply, discounted way down from the regular $226.24 price. That’s the lowest price we’ve seen on this product in a long time, making this a real bargain. If you are looking for an affordable combination digital scale and powder dispenser, this is very attractive pricing. By comparison, the new RCBS ChargeMaster Lite sells for around $250.00 and is back-ordered at most vendors. That means you can save at least $90.00 by buying RED instead of GREEN.
Got patches? Here’s a great deal on 100% cotton flannel patches. There are many sizes available, starting at $9.99 for 800 one-inch “17 Cal” patches. For 6mm rifles, we actually like the 1.25″ round “22/223″ sized patches priced at $11.99 for 800. Choose either round patches or square patches in most sizes. We generally like round patches for use with spire-tip jags, but some shooters prefer to wrap their patches around a jag or brush and square patches work better for wrapping. The large, 2″-square .30 Cal patches cost $17.99 for 800. These prices include FREE Shipping for Prime Members.
Share the post "Bargain Finder 84: AccurateShooter’s Deals of the Week"
Got a big shooting shopping list? Then here’s a great opportunity. Now through April 30th at 11:59 PM you can get $9.00 flat-rate shipping from Midsouth Shooters Supply, with a $99.00 minimum order. That can translate to significant savings on big orders, or heavy items. Compare the true shipping costs from other vendors to see what a good deal this can be (some vendors charge $15 to ship a couple boxes of ammo). Note: Regular hazmat charges apply to powder, primers, and other hazmat items.
If you’re shopping at Midsouth, here are some of the very good values you might want to check out:
Share the post "Flat Rate Shipping Offer at Midsouth Shooters Supply"
Vortex Optics and Hornady have joined forces to create what may be the most remarkable new bullet technology in the past 20 years. Vortex has adapted a miniature video system to fit inside the tips of rifle bullets. The micro-sized camera/transmitter was originally developed for miniature spy drones. Vortex cleverly figured out to make these tiny little video cameras work when carried on a spinning projectile launched from a rifle.
The revolutionary bullet-cam is the equivalent of the camera in the nose of a “smart” bomb or missile, but micro-miniaturized. This new technology allows you to literally watch your bullet fly into the target. For long-range shots with extended flight times, the view is mesmerizing. Hunters should be very excited. With the Bullet-Cam, you can record the “shot of a lifetime” on a trophy hunt. One has to commend Vortex for achieving this electro-optical breakthrough. Kudos also to Hornady for incorporating the micro-optics into shootable ammunition.
Vortex Video Shows New Bullet-Cam in Action:
A live feed from the Bullet-Cam streams right to your device for instant viewing. Once the Bullet-Cam hits the target, recording stops and the video is automatically uploaded to the VTX Cloud where it can be shared to social media.
Software Indexing Magic Creates Stable, Viewable Image
How is the image viewable though the bullet is spinning at thousands of RPM? The answer is surprisingly simple — and achieved through software. The bullet RPM is referenced by a microprocessor, so the camera’s software simply snaps a picture of the target every few micro-seconds, when the target is in exactly the same orientation. The lens is spinning, but it only captures visual data once every rotation (i.e. image capture is rotationally-indexed). This “stream of stills” is then blended into the video feed. What the viewer sees is a stable movie as though the camera was mounted on a non-rotating, fin-stabilized projectile. This rotationally-sequenced image-capture process made the whole project possible. We’re told that the Pentagon was so impressed with the technology that it is looking to fit Bullet-Cams into a variety of spin-stabilized ordnance, including artillery shells and large-caliber (.50 BMG) sniper rounds.
Vortex Engineer Ian Klemm, a top F-TR shooter, helped develop the innovative Bullet-Cam. Ian says: “Our goal with … Vortex products is to allow our customers to see things clearly from all vantage points. When it comes to bullet impact though, shooters have had to relay on traditional optics to determine accuracy from long distances. We were determined to provide an additional point of view (POV) to improve precision and overall performance. [We want] shooters to have the most advanced tools in the industry, to achieve the most accurate shots. With the Bullet-Cam you will always know if you are way off or dead on.”
Ten Bucks Per Shot — Great for Hunters
Considering the technology involved, the Bullet-Cam product is suprisingly affordable. A box of ten (10) cam-equipped cartridges is only $99.99. So, for about ten bucks per shot, you can actually see your shots fly downrange and into the target. That’s something that’s never been possible with sporting ammunition. This new technology unlocks a whole new world for precision shooters. And for hunters — the Bullet-Cam literally allows you to record the shot of a lifetime on a trophy animal. You can then share that memorable experience via Facebook, Twitter or other social media.
Share the post "Vortex and Hornady Introduce Revolutionary Bullet-Cam Ammo"
A stuck case is one of the boo-boos that all of us reloaders have faced from time to time. If proper lubrication is applied, then it should not be a problem. No matter if you are a seasoned reloader or new to it, this situation can happen. Take your time, use the proper procedures, and you will be back in business in no time! This article explains how to avoid stuck cases (through proper lubrication) and how to use a stuck case removal system.
