|
|
December 6th, 2009
 The RCBS ChargeMaster 1500 electronic powder scale and dispenser is the most popular product of its kind on the market. In our original Electronic Powder Dispenser Comparison Test, the ChargeMaster normally dispensed most kinds of powder faster than competitive units from Lyman and PACT. However, after the initial release of the ChargeMaster 1500, RCBS “tweaked” the software a bit to achieve more consistent charge-throws. This slowed down the process somewhat. Some owners have wanted to speed up their ChargeMaster. This IS possible with a relatively simple reprogramming. Most of the internal parameters of the Chargemaster can be modified, under guidance from the tech staff at RCBS.
Gunsmith and Forum member NAT Lambeth reports: “I thought My RCBS ChargeMaster 1500 Combo was fast enough. But I still called RCBS and asked for the programing changes to see if I could speed it up. It was a lot easier than I thought. My 1500 Combo was taking from 15-30 seconds to dispense the powder to the tenth of a grain. I reprogrammed the numbers and now it takes between 7 and 15 seconds to dispense to a tenth. This effectively doubled my loading speed. I only changed the HSB_A1, HSB_B1, and BSP_C1 settings.”
Key ChargeMaster Parameters with Default Settings
HSB_A1 (15.68) Grains under target weight to go from full to high speed
HSB_B1 (3.42) Grains under target weight to go from high to slow speed
BSP_C1 (1.08) Grains under target weight to go from slow to final trickle speed
Nat cautions that you should talk to a RCBS tech before attempting to re-program your ChargeMaster: “You will benefit from talking to the RCBS tech. I have now gone back and played with the numbers a couple of times. (The numbers given to me by the tech at RCBS were still a little conservative.) I think each machine may have its own likes and dislikes. If you get too aggresive with lowering your numbers it will over-throw your intended load.”
 Source for ALL the Parameters
There is an extensive discussion of RCBS ChargeMaster programming on the South Africa Hunting Rifle Shooting Assn. (SAJSV) Forum. In this SAJSV Forum ARTICLE, Jaco Brink lists virtually all the programming codes. Importantly, Jaco also provides the default values for various parameters. This is very important, because the ChargeMaster does not have a “return to default” option. Once you change any value, if you want to return to the original value you must enter it manually. Jaco cautions: “I have to advise you to only make changes to your scale if you are confident to do so, and remember that there is not a ‘return to default’ setting in the scale. If all else fails return your scale to the default settings [I have listed].”
CLICK HERE for list of RCBS ChargeMaster Default Programming Values
Use a McDonald’s Straw to Reduce “Over-Throws”
Jaco Brink provided another useful tip to avoid “over-throws” (excess charge weight): “The RCBS employee advised me to take a McDonnell’s straw (because it is thicker than a normal straw), cut off about a half inch piece and put it into the tube where the powder exits. This caused the last [few kernels] of an extruded powder to cluster less, and reduced the amount of overthrows dramatically.”
CLICK HERE for more ChargeMaster 1500 optimization TIPS.
November 5th, 2009
 In this feature, Bill Gravatt, President of Sinclair International, explains how to clean and maintain precision reloading dies. This article first appeared in Sinclair’s online Blog, The Reloading Press, where you’ll find many other useful Product Spotlights and ‘How-to’ articles.
Reloading dies if taken care of properly will provide years of service to their owner. Most dies are hardened and then micro-polished for that mirror internal finish many of the dies exhibit. Many of them are also treated with some type of rust preventative before they leave the factory floor. But dies still need some attention before they are put to use.
Clean Your Dies Before First Use
The first step in taking care of your dies starts when you receive them. We advocate cleaning all new dies before you begin to use them. Beginning with your sizing dies; take the decapping assembly completely out of the die body. Flush the decapping assembly with a good degreaser (such as Hornady One-Shot Cleaner & Dry Lube, Birchwood Casey Gun Scrubber or Shooter’s Choice Quickscrub III) and wipe the expander ball clean.
 The only part of the decapping assembly that should come in contact with your brass is the expander ball and the decapping pin. Pay particular attention to the decapping ball as it determines the final interior dimension (bullet grip) of your case neck. Make sure you inspect it after cleaning to make sure that the surface is clean and free of burrs.
Next, flush the interior of the die body out with some more degreaser. Using a pistol cleaning rod or a dowel rod, push a couple of wet patches all the way through the die. Then run a couple of dry patches through. Reassemble your sizing die and you should be good to go.
Seating Die Cleaning and Maintenance
Taking apart your seater is fairly simple depending on the complexity of your seating die. A standard seater just requires you to turn the seating stem out of the die body exposing the interior of the seater. Flush and clean both the body and seater as described above. Benchrest sliding sleeve seaters such as Forster or Redding Competition Dies have a few more parts involved. Just make sure as you take them apart you know how the spring is oriented and how any other parts such as chamber sleeves or seating plugs are arranged. Any springs or threads can be wiped down with a very rag or patch lightly coated with a fine oil. Make sure you inspect the opening in the seating stem for debris. You can twist a patch and use the end to clean out the smaller caliber stems/plugs.
 Regular Cleaning and Storage Advice
Regular maintenance of your dies should include their routine cleaning. Sizing dies collect excess lube off the cases and this lube can begin to build up. We have seen dents formed in the case shoulder from the hydraulic compression of the excess lube in the die when the case was sized. We recommend cleaning the dies every 500 to 1000 rounds depending on how frequently they are used and the cleanliness of your reloading area. For longer term storage of your dies, I recommend putting a light oil or rust preventative on them, especially if you have a shop that has a humid environment.
My reloading area is in the same building (different room) as my woodshop and I have to watch the dust so I keep most of my reloading dies covered or stored away. I keep a cover over my press and scales as well.
October 22nd, 2009
 The 2010 edition of the Hodgdon® Annual Manual has just been announced, and should be at newstands in January 2010. Now in its 7th year, the Hodgdon Annual Manual includes over 5,000 rifle and pistol loads, with information on 56 Hodgdon, IMR® and Winchester® powders. The new 2010 Manual features 44 cartridge updates, brand new data for the 6.5 Grendel and 6.5 Creedmoor, and updated propellant burn rate and usage charts.
Extensive reloading information is provided for popular cartridges such as the 17 Remington, 223 Remington, 204 Ruger, 6PPC, 308 Winchester, 338 Federal and more. In addition, the 2010 Manual includes articles by top gun writers like Layne Simpson and Jim Carmichael plus many other resources for shooters and reloaders.
Articles in the 2010 Hodgdon Annual Manual spotlight the new varmint/match powder, IMR 8208 XBR. Test lots of this new powder have shown truly exceptional temperature stability. In addition, IMR 8208 XBR should deliver excellent accuracy in cartridges such as the 6mm PPC, 6BR, 22BR, and .308 Winchester. Lou Murdica and Jim Carmichael have already recorded impressive benchrest wins with prototype IMR 8208 XBR.
The 2010 Hodgdon Annual Manual costs $8.99 and should be available at newsstands and gun dealers by January 2010. For more on the manual contact Hodgdon at 913-362-9455, visit Hodgdon.com, or write to 6231 Robinson, Shawnee Mission, KS 66202.
October 21st, 2009
Lee reloading products have always represented good “bang for the buck”. The Lee Classic Cast “O”-style press is no exception — it works as well as some other presses costing twice as much. One well-known “boutique” bullet maker has recently switched to Lee presses because the tolerances and lack of slop were actually superior to more expensive presses.
The Lee Classic Cast press is a well-designed unit with a strong, cast-iron frame and all-steel linkage. It has important (and very cool) features you won’t find on an RCBS RockChucker. First, the ram is drilled in the center and fitted with a plastic drop tube so spent primers drop right out the bottom (where you position your trash can). Second, the handle adjusts for length and “attack angle”. This allows you to change the leverage to suit your task. As Lee explains: “The start and stop position is adjustable with a 48-tooth, ratchet-type handle clamp. In addition, the handle length is completely adjustable. Shorten when you’re loading handgun and short rifle cases.” As you can see, you can also mount the handle on either side, left or right.
 
You can purchase the Lee Classic Cast Press for under $86.00 at major vendors. FactorySales.com offers the Lee Classic Cast for $73.40, item 90998. MidwayUSA sells the Lee Classic (item 317831) for $85.99. Natchez Shooters Supply also offers the Lee Classic for $80.99, item LEE90998.
 Mark Trope of SurplusRifle.com has written a detailed Review of the Lee Classic Press. He notes that the press is “southpaw friendly” and he praises the priming system. Mark found that the spent primer drop tube worked very well and that the press “works perfect and has great sensitivity” when seating primers.
Not yet convinced? CLICK HERE to read comments from actual Lee Classic owners. Here are some highlights:
“It has a large, heavy-duty 1-1/8″ diameter ram that has been drilled out for spent primers … and a long clear plastic hose attached to it so you can route it to a trash can. [This is] a VERY well thought-out way to collect ALL primers to your trash can when you’re decapping.” –D. Oldham
“Fit and finish are impeccable. The spent primer disposal system is simple and neat. There is no spring or flexing of any kind. There is virtually no play in the ram, which is a good tight fit in the frame. Operation is totally smooth.” –R. Smith
“Totally outclasses any other press in its price range. Runs with presses in the $100-$120 range.”–W. Rose
“I like…the position of the ram at priming. The Lee seats the primer with the ram at the bottom of the stroke vs. the RC II, which seats in the middle of the stroke. Priming at the bottom of the stroke gives you a much better ‘feel’.” –M. Gallagher
October 5th, 2009
 We interviewed Chris Hodgdon of Hodgdon Powder Co. and learned some important information about the IMR’s new 8208 XBR powder. First Chris confirmed that ADI (Australian Defense Industries Ltd.) is the manufacturer. The powder is a very small extruded powder, similar to H322 in kernel size. That means it packs densely in a case and meters well in manual powder measures. As to burn rate, Chris stated that IMR 8208 XBR is “a tad slower than H4895.” Chris confirmed that the powder’s distinctive qualities are temp stability in an ultra-wide temperature range and a very broad accuracy window. Chris said: “Jim Carmichael found he could go up and down [significantly] in his charge weight and the group size didn’t vary.”
Hodgdon has already begun shipping IMR 8208 XBR to “OEM manufacturers” according to Chris, who said a major manufacturer will be loading the powder into .308 Win ammo and possibly other cartridges. Chris hopes to send AccurateShooter.com some of the new 8208 XBR powder for testing within two weeks. When will the powder be available to the general public? Chris couldn’t give a firm answer, but he stated “we hope to start shipping in January, 2010, prior to SHOT Show.”
IMR 8208 XBR Load Data Now Online
The Hodgdon Reloading Center site has been updated to include IMR 8208 XBR load data for 41 cartridges. Go to www.data.hodgdon.com and select “Cartridge Loads”. Then you’ll need to input the rifle cartridge of your choice. We quickly found IMR 8208 XBR loads for the .223 Rem, 22 PPC, 22-250, 6 PPC, 6mm BR, 6.5 Grendel, and .308 Win, and many other cartridges. NOTE: For most of these cartridges, the stated “max load” velocities were NOT particularly impressive. So, be aware, that this initial load data is pretty conservative.
September 8th, 2009
Guns & Gear is a new television series produced by respected shooting sports journalist Jim Shepherd and Gun Talk Radio host Tom Gresham. Forum members who watched the debut episode of Guns & Gear gave it high marks, saying it was informative and well-made.
This week’s episode of Guns & Gear should interest our readers. The show features reloading tools from Sinclair International, the AR platform M&P 15 rifle from Smith & Wesson, and Nosler Accubond bullet penetration tests. Guns & Gear airs on the Versus Cable Network at the following times: Tuesdays at 3:00pm EST, Wednesdays at 8:30am EST, and Thursdays at 8:30am EST. For other time zones, check your local listings.
You can view segments from previous episodes and learn more about featured products by visiting www.gunsandgeartv.com.
July 28th, 2009
Precision Reloading, a South Dakota-based vendor of shooting supplies and reloading components, has launched its new, enhanced website. You’ll find the new site easier to navigate, with enhanced product descriptions and photos. The shopping cart system is also much faster and easier to use. Products are now organized in eight basic categories: Shotshell Reloading, Metallic Reloading, Muzzleloading, Hunting & Shooting Accessories, Optics, Gun Cleaning & Care, Books & DVDs, and Sale/Clearance items. Click on any main category and you’ll find products grouped by type. For example, under Gun Cleaning products, you’ll find handy links for “Bore Guides”, “Solvents”, “Patches & Jags” etc.; this lets you quickly easily compare multiple competitive products. We’ve found that’s much faster than trying to search, one by one, for a half-dozen different bore solvents, for example.
Precision Reloading’s new website also spotlights sale/clearance items with “Monthly Specials” and “Bargain Bench” entries. Among the current monthly specials we found the Vortex Viper 4-12x40mm Side Focus scope for just $362.99 (item VX04P). And in the “Bargain Bench”, you’ll find Wilson Caseholders for just $6.50 and Sinclair Expander Mandrels for just $3.99 per caliber.
July 11th, 2009
Having a quality funnel can help you get a carefully-measured powder charge in your cases, with no spillage, every time. If you’ve messed around with cheap plastic funnels you know that they can rock on the case mouth. Also, if the fit isn’t good, some kernels can end up on your bench, instead of inside the case.
Thankfully, precision, caliber-specific metal funnels are available to reloaders for about $10-11. Satern Custom Machining funnels feature an aluminum top with a caliber-specific, machined brass base/neck. Dick Saunders makes a simliar, turned-aluminum funnel sized for particular calibers. Both these metal funnels make reloading easier (and they are ideal for blackpowder loading because they do not give off static electricity). As Forum member Wes notes, with a fitted metal funnel: “the possibility of the funnel sliding to the side, and spilling powder all over the place is drastically reduced.”
Satern Aluminum/Brass Funnels
Steve Satern crafts rugged aluminum funnels with brass ends. The caliber-specific sizes offer a snug fit that keeps the funnel tight on the case neck while the powder is flowing. Forum member Danny Reever reports: “If you are tired of the generic ‘fits all’ funnels falling over and powder spraying every where, try one of the Satern funnels. Sinclair Int’l sells them and they are top notch.” SMike308 adds: “I have retired my plastic funnels after buying my first Satern funnel. I now have one for each different caliber that I load for. I especially like that the Satern has the brass weight at the bottom, which adds stability to the funnel.”
Satern funnels are sold by MidwayUSA (6mm $11.29), Satern Machining (6mm $10.49), and Sinclair International (Item 11-9XX, 6mm $11.95). Satern Machining also offers two types of universal funnels, 22-30 caliber and 30-50 caliber.
Saunders Aluminum Funnels
Some of our Forum members prefer the turned aluminum funnels made by Dick Saunders.
These are sold by Russ Haydon’s Shooters Supply for $9.95 each. Specify .17, .20, .22, 6mm, 6.5mm, .30 caliber or “all-purpose”. If you have questions, you can contact contact Saunders directly:
Dick Saunders
145 Delphi Rd.
Manchester, IA 52057
563-927-4026
June 18th, 2009
 DATELINE: June 18, 10:40 am Pacific Time
Here is an important product update. Sinclair International received a shipment of Sellier & Bellot rifle primers on June 15. These are good non-corrosive boxer primers made by a respected Czech munitions-maker. As of June 18, 10:30 am Pacific time, Sinclair has the following quantities of Sellier & Bellot rifle primers in stock:
S&B Sm Rifle Primers (item 25-8000): $33.60 per 1,000-ct box — 165 boxes in stock.
6/22/09 UPDATE: Sm Rifle SOLD OUT
S&B Lg Rifle Primers (item 25-8100): $36.40 per 1,000-ct box — 455 boxes in stock.
6/22/09 UPDATE: 150 boxes Lg Rifle remaining
Sinclair tells us: “The primers are leaving fast so if you need large or small rifle primers or know someone who does we have some at the moment. Visit our website at Sinclairintl.com to check availability or call 1-800-717-8211. We have more large rifle primers than small rifle primers. Please limit yourself to 5,000 primers since many of your fellow shooters are without any primers at the present time.”
May 3rd, 2009
 The RCBS Chargemaster 1500 Combo is the #1-selling electronic powder dispenser/scale system on the market. It was the top-performing unit in the Powder Dispenser Comparison Report we did a couple years back, and it still probably offers the best combination of features, speed, and weighing precision. Since its introduction, the RCBS Chargemaster has received a number of refinements. The internal software has been updated, the timing (of the powder drop) has been adjusted, the keypad has been upgraded and other smaller “tweaks” have been made.
If you haven’t tried one of these machines yet, you should. Provided you set it up correctly, making sure it’s level, and away from drafts, the Chargemaster will normally throw charges to ± 0.1 grains. That’s better accuracy than most persons can achieve using a manual powder measure and a balance beam scale (we know… we’ve checked on that.)
Video of RCBS Chargemaster in Slow-Motion
This video, created by a shooter in Norway, shows an RCBS Chargemaster dispensing 43.0 grains of Vihtavuori N140 powder. Using a Casio EX-F1 camera, the video was recorded at a high frame rate — up to 1200 frames per second. This allows very cool “Slow-Motion” playback. Check it out… you can see individual kernels of powder as they drop into the pan. At the end of the video you can watch the charge being thrown in “real-time”. Note how it slows down to trickle the last few tenths of a grain.
|
