|
|
November 28th, 2009
As an extended “Black Friday” sales promotion, Brownells is offering 10% off all orders over $150. This promo, which started on November 27th, runs through midnight, on “Cyber-Monday”, November 30th. To qualify for the 10% discount, visit brownells.com and use Coupon Code CYB to get 10% off any order over $150. NOTE: There are also many specially-priced items on sale all weekend long. You can use the 10% discount (Code CYB) even on these special sale items.
Sinclair International is running a similar promotion through midnight on Monday November 30th. Again you can get 10% off any purchase. However, to qualify for the discount, your total order must exceed two hundred dollars ($200.00). To get your discount (on orders over $200) use Promotion Code SAVE10 during online check-out.
November 14th, 2009
 Sinclair International has a new tool assembly that lets you sort bullets by base to ogive length. The $79.95 Sinclair Bullet Sorting Stand with Dial Comparator (item 59-2000) comes with a heavy black granite base that stays put on your loading bench. The included dial indicator has a quick-release lever allowing easy placement and removal of bullets into the comparator. This lever allow the spring-loaded indicator shaft to pop up out of the way.
The special base comparators used with this tool (see photo), are sold separately for $10.99, and are offered in 22 caliber, 6mm, 6.5mm, 7mm, 30 caliber, and 338 caliber. The sorting stand can also be used with Sinclair multi-caliber hex comparators (item 09-700, $18.25).
Measuring Bullet Bearing Surface with Calipers and Comparators
While we like this Sinclair tool, the same function can be performed with a regular set of calipers, using two comparators with caliber inserts. If you use the Hornady (formerly Stoney Point) OAL system you probably already have a #B2000 comparator body and a caliber-specific insert ($3.99 at Grafs.com).
Buy a second body ($14.39 at Grafs.com) and second insert (of the same caliber) and mount one on each caliper jaw, opposite each other. Tuck the bullet’s boat-tail in one insert and the “pointy end” in the other, and you can quickly measure the bearing surface. It takes a few tries to get the right “feel” of how hard to close the caliper jaws. But if the comparator bodies are set up right, the process should be quite repeatable, and you can probably measure just as fast with calipers as with the Sinclair measuring stand. However, the Sinclair unit should be a bit more precise, if you’re trying to resolve bullet lengths to less than one-thousandth. If you want to measure base to ogive (rather than bearing surface length), just remove one comparator and measure with the heel of the bullet (end of boat-tail) touching one jaw, and the bullet’s “pointy end” in the remaining comparator.
November 1st, 2009
For years, Sinclair Int’l has offered a reamer for small, BR-sized flash-holes, product #07-3000. This popular tool features an 0.0625″ cutting tip to uniform the .059″ flash-holes on Lapua 220 Russian, 6mmBR, 6.5 Grendel, and 6.5×47 brass. Sinclair’s tool works from the outside, indexing off the primer pocket. For those people who believe in the utility of reaming small flash-holes (an open question), the Sinclair “outside-in” design may be the best. But until now, there has been no equivalent “outside-in” reamer for cases with large flash-holes.
 Sinclair recently introduced its NEW .081″ large flash-hole reamer, item #07-3081. This $37.50 tool is designed to ream standard flash holes (.080″) to exactly .081 inch, both for small primer pockets and large primer pockets. This tool will remove most burrs left in manufacturing and will uniform the flash-hole diameter of all your brass to ensure consistent ignition.
Double-Ended Design Works with Both Small and Large Primer Pockets
Sinclair’s all-stainless three-piece tool features a double-ended reamer guide for both large and small primer pockets, a knurled handle for easy turning and a straight fluted .081″ reamer. It is designed for all cartridges (with either small OR large primer pockets) with standard .080″ flash holes.
As one Sinclair customer noted: “This is a tool that has been needed for a long time.” As a result, the .081″ flash-hole reamers have been back-ordered through 12/1/2009. But if you order now you should have yours within 5-6 weeks.
IMPORTANT: We recommend, if you order this tool, that you mic the actual diameter of the cutter tip. We have found that some flash-hole reamers, of ALL brands, arrive with slightly oversized cutter tips. Indeed we’ve seen tip diameters of other brands (not Sinclair) vary by as much as .006″ (six-thousandths). You want to make sure you don’t have an oversize cutter before you ream hundreds of cases.
September 8th, 2009
Guns & Gear is a new television series produced by respected shooting sports journalist Jim Shepherd and Gun Talk Radio host Tom Gresham. Forum members who watched the debut episode of Guns & Gear gave it high marks, saying it was informative and well-made.
This week’s episode of Guns & Gear should interest our readers. The show features reloading tools from Sinclair International, the AR platform M&P 15 rifle from Smith & Wesson, and Nosler Accubond bullet penetration tests. Guns & Gear airs on the Versus Cable Network at the following times: Tuesdays at 3:00pm EST, Wednesdays at 8:30am EST, and Thursdays at 8:30am EST. For other time zones, check your local listings.
You can view segments from previous episodes and learn more about featured products by visiting www.gunsandgeartv.com.
June 1st, 2009
Lapua brass is so good that you’ll be tempted to just load and shoot, if you have a “no-turn” chamber. However, some minimal case prep will ensure more uniform neck tension. This will produce better accuracy, more consistent bullet seating, and lower Extreme Spread and Standard Deviation (ES/SD). Lapua brass, particularly 6BR, 6.5×47, .243 Win and .308 Win comes from the factory with tighter-than-optimal necks. Before you seat bullets, at a minimum, you should inside chamfer the case mouths, after running an expander mandrel down the necks.
The expander mandrels from both Sinclair and K&M will leave the necks with enough neck tension (more than .001″) so you can then seat bullets without another operation. Put a bit of lube on the mandrel before running it down the necks — but remove any lube that gets inside the necks before seating bullets.
Both Sinclair and K&M Tools make a die body specifically to hold expander mandrels. Sinclair’s Generation II Expander Die Body (item 05-3000, shown above) completely captures the mandrel within the die so the mandrel cannot pull out. An O-ring in the die cap allows the mandrel to float a bit and find its own center within the case neck. This $24.95 unit fits caliber-specific expander mandrels (item E-XX, $8.75) which measure approximately .001″ less than bullet diameter for each caliber. Once you run the Sinclair expander mandrel down the necks of Lapua brass, after you account for brass spring-back, you’ll have about .002″ neck tension. This will make the process of seating bullets go much more smoothly, and you will also iron out any dents in the case mouths. Once the case mouths are all expanded, and uniformly round, then do your inside neck chamfering/deburring. The same expander mandrels can be used to “neck-up” smaller diameter brass, or prepare brass for neck-turning.
Forum member Mike Crawford adds: “These expanders can also reduce runout from offset seating. Prior to bullet seating, expand the sized necks to force thickness variance outward. With the Sinclair system, the necks will springback fine, and will not be pulled out of center. This leaves plenty of tension, and bullets seated more centered. I do this, even with turned necks, to get improved seating.”
Mandrels vs. Expander Balls on Decapping Rods
If you haven’t acquired an appropriate expander mandrel for your brass, but you DO have a full-length sizing die with an expander ball, this will also function to “iron out” the necks and reduce tension. However, using a die with an expander ball will work the necks more — since you first size them down, then the ball expands them up again. Typically (but not always), run-out is worse when using an expander ball vs. an expander mandrel.
|
