Eurooptic vortex burris nightforce sale




teslong borescope digital camera barrel monitor


As an Amazon Associate, this site earns a commission from Amazon sales.









August 16th, 2016

Handy Adjustment Lever Kits for Harris Swivel Bipods

Bipod Harris Swivel Handle Lock S Lever Kit Eabco.com

We like the swivel (“S”) version of the Harris bipod. The swivel (actually tilting) capability of the bipod allows you to tilt (cant) your rifle around the bore axis to level the rifle on a side slope or uneven ground. Unfortunately, the swivel tensioner (friction knob) that comes standard with a Harris swivel bipod leaves much to be desired. The tensioning knob is hard to adjust with your fingers. The small knurled ring doesn’t offer enough leverage. When it’s tight enough to prevent movement it’s hard to release. For this reason, many folks replace the standard knurled ring with a rotating adjustment lever with push-button release. This works great and is easy to install.

While you can buy levers from various sources, Eabco.com has a tried-and-true system that works with both Harris and Caldwell XLA-S swivel bipods: “Our new S-Lever Tension Lever is an economical replacement for the friction tensioning knob to give you much better control and leverage.” For just $12.95, Eabco.com delivers all the parts you need for the upgrade. Shown below are instructions for installing the Eabco S-Lever.

Bipod Harris Swivel Handle Lock S Lever Kit Eabco.com

Permalink Gear Review 3 Comments »
March 4th, 2015

Swivel Bipod Locking Handle Options

KMW Pod-Loc BipodIf you’ve ever used a Harris Swivel Bipod, you know that, without tools, it is difficult to put enough tension on the swivel locking knob to really lock the unit solid. And, if you do manage to get the knob really tight (perhaps by using pliers), it is difficult to loosen with fingers alone.

That was why Terry Cross and the folks at KMW Long Range Solutions invented the Pod-Loc™. This system replaces the knurled swivel tension knob with a push-button adjustable handle. Using the handle you can easily set the swivel tension at any level from loose to “rock solid”. And you can release tension to adjust the bipod to different terrain just as easily. The KMW Pod-Loc™ retails for $24.99 at Brownells.com and Sinclair Int’l.

KMW pod-lok lock bipod handle swivel

Pod-Loc™ Installation Instructions

How to Build Your Own Bipod Swivel Locking System
While we use genuine KMW Pod-Locs on our rifles, readers on a tight budget, or who have a large collection of bipod-equipped rifles, can economize by putting together their own swivel locking systems from off-the-shelf components. You need two parts per installation: a push-button swivel handle and a 3/16″ spacer. Levers and spacers are both available online from www.T-Nuts.com. The spacer is part #SS1 ($1.00). T-Nuts offers a variety of suitable handles, ranging in price from $7.00 to $10.00. So, by sourcing the parts, you can outfit three bipods with swivel adjusters for the cost of one Pod-Loc.

T-Nuts Bipod Handle lock

We recommend the Nylon/Stainless BPL/NS model ($7.70), but you may prefer the all-metal BPL-Z ($8.50), or the shorter BPL-Micro model ($8.50). The compact Micro lock does not protrude past the body of the bipod, yet is still easily grasped. T-Nuts supplies one 3/16″ spacer with most of its bipod handles. T-Nuts handles are also available with a metric M6x1.0 thread for use with imported bipods such as Outers and Rockport.

Installation is Easy — With the Right Socket
To install a swivel locking system, first you’ll need a 1/4″ socket to remove the keeper nut from the threaded pivot rod. (During this process, you’ll need to keep pressure on the pivot rod retaining pin on the opposite side of the bipod.) Don’t try to remove the keeper nut with pliers or an open-end wrench. You really need the correct socket. Once that keeper nut is removed, then unscrew the knurled tension knob/ring. This is attached to the same threaded shaft as the keeper nut but you should be able to remove it without tools.

After the knurled tension ring is off, it is easy to put your handle on the bipod. First slip the 3/16″ spacer over the threaded pivot rod. Keeping finger pressure on the pivot rod retaining pin (on reverse side), then spin on the T-Nuts handle. Rotate the handle inwards until it firmly locks the bipod swivel mechanism. By pushing the button in the head of the handle, you can swing the handle left or right to set its position without altering the swivel tension.

Permalink Gear Review 5 Comments »
November 14th, 2014

Harris Bipods on Sale at Midsouth Shooters Supply

Got Bipod? If you’re in need of an adjustable two-legged friend for the front of your favorite rifle(s), Midsouth has you covered. Right now Midsouth Shooters Supply has a wide selection of Harris Bipods in stock at attractive prices. For example, the Harris 6″-9″ BR model with leg notch is just $69.68. That’s ten bucks cheaper than we’ve found elsewhere. From small to tall, Midsouth carries Harris bipods for your intended applications. Midsouth also sells a variety of authentic Harris mounting adapters, including rail adapters, and flat fore-end adapters.

Midsouth Shooters Supply Harris Bipod Sale BR Swivel

Midsouth Shooters Supply Harris Bipod Sale BR Swivel

Permalink Hot Deals, Tactical No Comments »
February 26th, 2011

New Neck-Turning Tool Holder from 21st Century Shooting

The wizard tool designer who runs 21st Century Shooting has invented a clever yet inexpensive new bench accessory that makes it much easier to turn case-necks. 21st Century’s new Neck Turning Tool Swivel Bracket gives you a “third hand” when using the 21st Century Neck Turning Tool, simplifying the process of neck turning, particularly when using power.

neck turning tool bracket

CNC-machined from aluminum billet, 21st Century’s Swivel Bracket mounts right on your bench. You can either attach it semi-permanently with screws or simply clamp it in place. Adjust your neck-turning tool (red unit in photo), at any angle from 0-90°, for best viewing of the cutter operation. With your neck-turning tool attached to the bracket, you have easy access to the arbor adjustment screw, arbor screw clamp, and the bracket rotation clamp screw. Once you’ve adjusted the angle, and locked the neck turner in place with the supplied Allen wrench, you can concentrate on turning the case, either by hand, or with power assist. The neck-turning tool is held securely; however, rubber bushings on the bracket allow the neck-turning tool to “float” just enough to work properly when using power.

This new Neck Turning Tool Swivel Bracket is simple, but very effective. It really does help you turn necks with greater ease and a greater sense of security. Importantly, the bracket lessens hand fatigue. No more “cramped hand syndrome” from struggling to hold the neck-turner steady. We really like this little device, and it only costs $19.95. However, for the time being, the Swivel Bracket ONLY works with the 21st Century Neck Turning Tool — it does NOT work with a Hornady, K&M, Neilson, or Sinclair Neck Turning Tools. For more info, call 260-273-9909 or visit 21stCenturyShooting.com.

Permalink Gear Review, New Product, Reloading 5 Comments »