Eurooptic vortex burris nightforce sale




teslong borescope digital camera barrel monitor


As an Amazon Associate, this site earns a commission from Amazon sales.









January 1st, 2017

6.5 Creedmoor — Velocity and Barrel Length — What to Expect

Rifleshooter.com 6.5 Creedmoor cut-down test

What do you get when you cut a 6.5 Creedmoor-chambered barrel down to just over 16 inches? A lot more velocity than you might think. Our friends at Rifleshooter.com recently did a barrel cut-down test with 6.5 Creedmoor test rifle, shortening the barrel from 27 to 16.1 inches in one-inch increments. Surprisingly, with a 142gr Sierra MK, the total velocity loss (as measured with a Magnetospeed) was just 158 FPS, an average of 14.4 FPS per inch of barrel length. With the lighter 120gr A-Max bullet, the total velocity loss was 233 FPS, or 21.8 FPS average loss per inch of barrel.

CLICK HERE to SEE All Velocity Values at All Barrel Lengths

To perform this velocity test, our friend Bill, Rifleshooter.com’s editor, built up a 6.5 Creedmoor rifle using a Remington Model 7 action, 1:8″ twist Green Mountain CM barrel, and MDT LSS Chassis, all obtained from Brownells.com.

Test Procedure
Five (5) rounds of each type of cartridge were fired at each barrel length and the velocity data was recorded with a MagnetoSpeed V3 barrel-mounted chronograph. The rifle was then cleared and the barrel was cut back one inch at a time from 27″ to just over 16″. NOTE: During this winter test, the air temperature was a very chilly 23° F. One would expect higher velocities across the board had the outside temperature been higher.

Read Full Story with All Test Results at Rifleshooter.com

The photo below shows how the barrel was cut down, inch-by-inch, using a rotary saw. The barrel was pre-scored at inch intervals. As the main purpose of the test was to measure velocity (not accuracy) the testers did not attempt to create perfect crowns.

Rifleshooter.com 6.5 Creedmoor cut-down test

6.5 Creedmoor vs. Other Mid-Sized 6.5mm Cartridges
The 6.5 Creedmoor is a very popular cartridge with the tactical and PRS crowd. This mid-size cartridge offers good ballistics, with less recoil than a .308 Winchester. There’s an excellent selection of 6.5mm bullets, and many powder choices for this cartridge. When compared to the very accurate 6.5×47 Lapua cartridge, the 6.5 Creedmoor offers similar performance with less expensive brass. For a tactical shooter who must sometimes leave brass on the ground, brass cost is a factor to consider. Here’s a selection of various 6.5 mm mid-sized cartridges. Left to right are: 6.5 Grendel, 6.5×47 Lapua, 6.5 Creedmoor with 120gr A-Max, 6.5 Creedmoor with 142gr Sierra MK, and .260 Remington.

6.5 Creedmoor Rifleshooter.com velocity barrel cut cut-down test saw blade

When asked to compare the 6.5 Creedmoor to the 6.5×47 Lapua, Rifleshooter.com’s editor stated: “If you don’t hand load, or are new to precision rifle shooting, get a 6.5 Creedmoor. If you shoot a lot, reload, have more disposable income, and like more esoteric cartridges, get a 6.5×47 Lapua. I am a big fan of the 6.5×47 Lapua. In my personal experience, the 6.5×47 Lapua seems to be slightly more accurate than the 6.5 Creedmoor. I attribute this to the quality of Lapua brass.”

Permalink Bullets, Brass, Ammo, Gunsmithing, Tactical 3 Comments »
December 23rd, 2016

Tactical Bonanza — Save $125.00 on McMillan A5 Stock

McMillan A5 Tactical Stock Sale Discount Christmas

Here’s a great deal for you tactical guys out there. Now through January 2, 2017, McMillan Fiberglass Stocks is offering $125.00 off its popular A5 Stock. And what’s more, you can even get FREE Shipping: “Take $125 off your purchase of the McMillan A5 – Standard Stock in our online retail store and receive free shipping! Use promo code: HOLIDAYSALE16 . Supplies are limited. Offer is only valid for the online retail store. Hurry, this offer ends Monday, January 2, 2017.”

DROP IN READY FOR:
— Right hand Remington 700 short or long action.
— BDL hinged floor plate or Badger M5 Detachable Box Magazine.
— Remington varmint/sendero/tactical/5R barrel.

McMillan A5 Tactical Stock Sale Discount Christmas

On McMillan’s A5 Standard Page, you can select your desired variation of the A5 — select color, action length, inletting type and more. NOTE: Offer is only valid for the online retail store. Free shipping applies to orders in the Continental USA.

McMillan A5 Sale tip from Edlongrange. We welcome reader submissions.
Permalink Hot Deals, Tactical 1 Comment »
December 17th, 2016

Tac Talk: Six Tactical Slings Reviewed by 6.5 Guys

6.5 Guys tactical precision sling review
Photo shows Precision Rifle Sling from Armageddon Gear.

A good sling is a vital accessory for a hunting or tactical rifle. Along with enabling over-the-shoulder carry, a good “tactical” sling will also provide support for shooting from hasty or improvised shooting positions. In fact, in many tactical/practical precision matches there will be at least one positional shooting stage or a stage where only a sling may be used for support (that means no bipod, no tripod, no sandbags, and no shooting sticks). The 6.5 Guys, Ed and Steve, recommend tactical slings that allow quick set-up and easy adjustment. The best slings allow shooters to quickly slip into them and then make rapid fine-tuning adjustments to build a stable shooting position.

Six Tactical/Practical Slings are Reviewed in this Video:

In this episode, Ed and Steve provide an overview and compare/contrast different designs and the functionality of six popular slings from these suppliers: Armageddon Gear, Tab Gear, Rifles Only, Hard Target Interdiction, Short Action Precision, and Accuracy International.

To learn more about tactical/practical shooting disciplines, or to access more shooting gear/accessories reviews by Ed and Steve, visit 65guys.com and subscribe to the 6.5 Guys’ YouTube Channel.

6.5 Guys Slings tactical

Video Tip from Boyd Allen. We welcome reader submissions.

Permalink - Videos, Tactical 3 Comments »
December 16th, 2016

Accuracy Int’l-Style .22 LR for Rimfire Cross-Training and Plinking

Keystone Arms Crickett CPR Precision Rifle AICS Accuracy International Int'l Tactical Chassis Rifle Rimfire .22 LR 22LR

Keystone Sporting Arms has created a new rimfire rifle that shares the looks and ergonomics of the Accuracy International AICS. Keystone’s new Crickett Precision Rifle (CPR) is a single-shot .22 LR bolt action rifle that uses the barreled action from the Crickett series of rifles. Trigger pull weight is 2.5-3.0 pounds. The AICS Classic-style stock is ambidextrous, but only a right bolt, right port version of the CPR is offered at this time, model KSA2150. Stock length of pull is adjustable (via spacers) from 11.5 to 13.5 inches, and there is an adjustable cheek-piece.

The Crickett Precision Rifle should be available in January 2017 and retail for approximately $310.00. This small .22 LR bolt action should appeal to Accuracy International fans who want a rimfire rifle for low-cost cross-training. This could also be a good first rifle for a young shooter. And if Dad owns a real Accuracy Int’l AICS rifle, the little AI clone would be a fun rimfire rig for son or daughter. That way the youngster(s) could shoot a smaller version of their parent’s rifle. Like father, like son (or daughter)!

Reader Boyd Allen likes this little rifle, which has a length of pull suitable for younger shooters: “I like seeing parents taking their kid(s) to the range, developing the next generation of shooters. For the price of what some guys spend on a set of fancy rings, you can purchase this little rifle and a youngster can enjoy shooting a rimfire that looks like the real-deal tactical rigs used by the ‘Big Boys’. That’s how you capture a kid’s interest.”

Permalink New Product, Tactical 1 Comment »
November 9th, 2016

6.5 Guys Talk about PRS, Reloading, Match Strategies and more…

65guys.com 6.5 Guys PRS Tactical Ed mobley steve lawrence

Gearlocker.nz, a New Zealand outdoor sports website, recently interviewed our friends Ed and Steve, aka the “6.5 Guys”. In this Gearlocker Video Interview, Ed and Steve cover many topics including Precision Rifle Series matches, gear selection, and effective hand-loading techniques. Kerry, the creator of Gearlocker.nz, writes: “The 6.5 Guys are Steve and Ed, two guys who decided to start documenting their progress in long-range practical precision shooting. They have built a dedicated following on YouTube and Facebook. Consistently putting out high-quality content [covering] their equipment choices and use, the 6.5 Guys have created a fantastic resource for anyone involved in shooting.”

Click image below to watch 6.5 Guys interview on Gearlocker.nz:
6.5 Guys Interview Gearlocker New Zealand

Who are the 6.5 Guys? They are Steve (left) and Ed (right), a pair of avid shooters based in the Pacific Northwest. They have released dozens of helpful videos on the 6.5 Guys YouTube Channel.

6.5 guys 65guy.com annealing video YouTube shooting

You can check out the 6.5 Guys’ website at www.65Guys.com. Below is a sample from one of the 6.5 Guys’ best articles — Five Tips on getting started in practical/tactical matches.

We often meet people who are new to long range precision shooting, and want to improve their knowledge and skill level. However, they aren’t sure if they are ready to sign up to compete in a match. They often ask, “What knowledge or skills [and gear] are necessary to compete in a match?”

TIP ONE: Make Plans and Commit to Go

First you need to start by finding a match to attend. We recommend starting with any match that may be within a reasonable driving distance. This may likely be a local “club” match, many of which are held on a regular basis. Once you decide on the match you want to attend, do your homework. This means finding out if you need to pre-register or pre-pay the match fee. Commit to going by registering for the match and putting it on your schedule.

>> CLICK HERE to READ FULL ARTICLE on 65Guys.com

Permalink - Videos, Tactical 1 Comment »
October 11th, 2016

2016 GAP Grind — Biggest Precision Rifle Series Event Ever

GAP Grind 2016 George Gardner
Facebook photo by Mike Bowers

GAP Grind 2016 George GardnerThe 2016 GAP Grind, the biggest Precision Rifle Series event in history, was a huge success. Pro Class winner Jim See reports: “What a weekend! The GAP Grind was one of the best-run matches I have ever shot. George Gardner, Shannon Kay, and some of the best ROs in the sport ran 236 shooters [firing 200+ rounds of ammo each] in about 18 hours over two days. Bushnell Sports Optics and G.A. Precision were the title sponsors. Thank you for your efforts to host matches like the Pro-AM. Congrats to Nick Steder and Matthew Saban for the win on the Team portion of the event. I competed against many friends at this match, some shined and some struggled. All of them are top notch. Thanks guys for the help and support through-out the year.”

GAP Grind 2016 George Gardner

GAP Grind 2016 George Gardner
Ramia Whitecotton Facebook photo.

Jim See reports: “Day 2 had every shooter on his own point scoring, with the Amateurs getting coaching from their PRO — that’s such a great match format for learning. My Surgeon Rifle in 6.5×47 Lapua ran flawlessly with my Gen 2 Vortex Razor allowing Berger Bullets to find their mark. My new friend Clifton Reasor brought some of the new Game Changer bags to the match and I snagged one Saturday night. Great product and aptly named — this thing has earned a permanent place in my pack.”

GAP Grind 2016 George Gardner
Josh Temnnen Facebook photo

Charles R. added: “Shannon Kay & George Gardner did an outstanding job running the largest PRS match in history. The ROs and support staff were exceptional. So much greatness in this match…”

One stage required the use of “human support” by one’s team-mate. Here Shooting USA’s John Scoutten provides a strong shoulder for a female competitor.
GAP Grind 2016 George Gardner
Ramia Whitecotton Facebook photo.

LITTLE GIRLS GRIND TOO

There were some very young and very talented junior lady competitors at this year’s GAP Grind. These school-girls had fun and showed the big boys a thing or two.

GAP Grind 2016 George Gardner

George Gardner says this little lady (above) can shoot: “300-yard positional mover, 9 years old, 4 hits! This is what it’s all about people — GAP Grind Pro-Am!”

GAP Grind 2016 George Gardner

Mike R. says: “I couldn’t be more proud of my daughter (above) shooting the GAP Grind. She had a great time and did pretty well for her first huge match flying solo. The good news is she really likes shooting, the bad news is she really likes shooting! I’m looking forward to taking her to many more matches. Thanks Shannon Kay and George Gardner for letting her shoot the Grind. Thanks Alison T. for being her partner. She had a blast!” (photo by Mike R.)

2016 GAP GRIND Gallery

Enjoy the images from the 2016 GAP Grind. Photos, unless otherwise indicated, come from Ramia Whitecotton’s GAP GRIND 2016 photo album.

GAP Grind 2016 George Gardner

Here’s a “Dawn Patrol” shot from Bryan Sikes. He mastered this stage: “6:00 am cold bore…..nailed it!”
GAP Grind 2016 George Gardner

The Pipeline Stage was claustrophobic…
GAP Grind 2016 George Gardner

With 236 competitors, the firing lines at the 2016 GAP Grind were full.
GAP Grind 2016 George Gardner

The shooting platform offered a double-decker challenge…

GAP Grind 2016 George Gardner

Editor’s Comment: It’s great to see such a well-attended and well-run event. Many participants reported that this was probably the “best GAP Grind ever”. That said, we notice from the photos that many competitors did not use eye protection. For myriad reasons that should be obvious, we strongly encourage all competitive shooters, no matter what their discipline, to use quality eye protection whenever shooting firearms.

Permalink News 3 Comments »
October 6th, 2016

Precision Rifle Blog Reveals Muzzle Brake Blast Patterns

Precision Rifle Blog Muzzle Brake Test Blast Powder

For a prone shooter, particularly on dusty, dirty or sandy ground, muzzle blast is a major bummer. Muzzle blast can be very disturbing — not just for the trigger-puller but for persons on either side of the gun as well. Some muzzle brakes send a huge shockwave back towards the shooter, and others send blast towards the ground, kicking dirt and debris into the prone shooter’s face. If there was a way to illustrate those factors — shockwave and debris — that might help shooters select one brake design over another.

GO to PRB Muzzle Brake Blast Pattern TEST PAGE

Precision Rifle Blog Muzzle Brake Test Blast Powder

Cal Zant at PrecisionRifleBlog.com applied a unique blend of creativity and resourcefulness to try to answer that question for 20+ muzzle brakes. Using high-speed photography and household products, he captured the blast pattern of 20+ different brake designs for easy side-by-side comparison. Can you figure out how Cal managed to show muzzle brake blasts so clearly? His “hi-viz” solution, revealed in the article, is very clever. See the eye-opening results for 20+ brakes, with illustrative photos, by visiting the Precision Rifle Blog Muzzle Brake Ground Signature Test Page.

Permalink - Articles, Tactical No Comments »
September 2nd, 2016

KRG 180-Alpha Tactical Chassis for Savage Actions

KRG 180 alpha Savage Tactical chassis pre-fit PRS

Can a budget-priced Savage shoot like a Sako TRG 22? Well, adding a custom “pre-fit” barrel and a state-of-the-art chassis system can transform a “Plain Jane” Savage into a serious tactical rifle. And now Kinetic Research Group (KRG) offers a new fully-adjustable chassis that’s just the ticket for a Savage tactical conversion. Just get a used Savage action, spin on a Criterion, Pac-Nor, or Shilen pre-fit barrel, and add the new 180-Alpha Chassis from KRG.

KRG 180 alpha Savage Tactical chassis pre-fit PRS

KRG offers 180-Alpha Chassis for Savage rifles. This fully-adjustable, light-weight (3.5 lbs) chassis fits Savage short action rifles with 4.4″ action bolt spacing. The 180-Alpha features tool-less cheek-piece height adjustment, spacer Length-of-Pull (LOP) adjustment, buttpad height adjustment, and plenty of accessory mounting positions. Suggested retail price for the 180-Alpha starts at $768.00 for the side bolt-release version. A bottom-release model is slightly more.

CLICK HERE for Specifications of KRG 180-Alpha Stock for Savages.

Compare KRG’s 180-Alpha Chassis to the hardware on the real deal — a Sako TRG 22 with adjustable, folding stock (model JRSM416, shown below). This SAKO TRG22 rifle in .308 Winchester retails for $5,198.00. With KRG’s 180-Alpha chassis you can put together an ergonomically-similar tactical rifle for thousands less.

KRG 180 alpha Savage Tactical chassis pre-fit PRS

Using the KRG Chassis, a take-off Savage action, and a premium pre-fit barrel, you can build a similar system for around $1540.00. Here’s how we get that figure: $370.00 for Criterion pre-fit barrel, $400.00 for action (YMMV), and $768.00 for stock (Total $1538.00).

KRG produces other adjustable, modular chassis systems for bolt-action rifles. KRG’s popular Whiskey 3 Chassis system fits the Tikka T3, Remington® 700™, Sako M995, Badger M2008, and 700 Long Action. The KRG X-RAY Chassis fits the Rem 700 Short Action, and Tikka T3, and the 180 X-RAY fits the CZ-455, Howa 1500, and Weatherby Vanguard platforms.

KRG 180 alpha Savage Tactical chassis pre-fit PRS

Product Tip by EdLongrange. We welcome reader submissions.
Permalink New Product, Tactical No Comments »
August 13th, 2016

New Howa Tactical Rig — Howa Chassis Rifle (HCR)

Howa HCR Chassis Rifle PRS Tactical Aluminum stock HACT Trigger

Here’s an item for tactical and Precision Rifle Series (PRS) shooters. Howa is releasing a new rifle with a modular metal chassis. The new Howa HCR (Howa Chassis Rifle) combines a Howa 1500 barreled action with a modern, fully-adjustable aluminum chassis. The Howa’s MSRP is $1299.00, so the HCR is directly competitive with the Ruger Precision Rifle (RPR). Available chamberings are: .223 Remington, .243 Winchester, 6.5 Creedmoor, and .308 Winchester.

Howa HCR Chassis Rifle PRS Tactical Aluminum stock HACT Trigger

Mounted on an AR-style buffer tube system, the Howa HCR utilizes the fully adjustable LUTH-AR MBA-3 stock. Length of Pull is adjustable form 12.5″ to 16.75″. Comb height is also adjustable to fine tune for scope height-over-bore. Weight with a 24″ barrel is 10.2 pounds (before optics), so this Howa HCR is lighter that some similar rifles on the market.

Howa HCR Chassis Rifle PRS Tactical Aluminum stock HACT Trigger

Howa HCR Features

• Howa 1500 Barreled Action with 20″ and 24″ Heavy Barrel options
• Black 6061-T6 Aluminum Chassis with Free-Float M-LOK Forend
• LUTH AR Buttstock with LOP Adjustment (12.5″ to 16.75″) and Adjustable Comb
• 10-RD ACCURATE Detachable, Teflon-coated Steel Magazine
• Two-Stage H.A.C.T. Trigger
• 3 Position Safety

Howa HCR Chassis Rifle PRS Tactical Aluminum stock HACT TriggerThe HOWA HCR features an adjustable, two-stage HACT trigger, set for about 3 pounds (combined stages). Crisp and repeatable, this is an excellent trigger for a factory gun. In our opinion, the HACT trigger is clearly superior to the trigger on the Ruger RPR, as well as the Savage AccuTrigger. And there is no annoying Glock-style safety lever in the middle of the trigger blade.

Available in .223 Rem, .243 Win, 6.5 Creedmoor and .308 Win chamberings.

NOTE: For all chamberings, 24″ barrels are offered, with 20″ options for the .223 Rem and .308 Win as well. Twist rates are 1:9″ for .223 Rem, 1:10″ for .243 Win, 1:8″ for 6.5 Creedmoor, and 1:10″ for .308 Win. We think .243 Win shooters will NOT be happy with the 1:10″ twist. We would prefer to see a 1:8″-twist for the .243 Win so it can shoot the 105-115 grain 6mm bullets. Most competitive 6mm shooters will want a true 8-twist or even a 1:7.5″.

Permalink New Product, Tactical 11 Comments »
August 3rd, 2016

Truckloads of Tikka T3s on Sale at EuroOptic.com Right Now

Tikka T3 sale inventory closeout reduction discount truckload

Looking for a great price on an excellent hunting rifle? Here is the Tikka Deal of the Decade. EuroOptic.com has received nearly 3,500 Tikka T3 rifles, which will be sold at deep discounts as part of an inventory clearance program by Beretta, Tikka’s parent company. The Tikka T3 is a good, stout rifle with a smooth, 3-lug action, crisp trigger, and quality barrel. Accuracy is typically well under 1 MOA (for three shots). T3 barreled actions also are a good “core” for a tactical build. The strong T3 action handles detachable magazines, and fits a variety of third-party stocks such as McRees Precision G7 and G10 chassis systems.

Our friend Jason Baney of EuroOptic.com tells us: “We have two tractor-trailer loads of Tikka T3 rifles (about 3500 units) dropping here today…and the sale prices are amazingly low. I am sure it will take a day or so to get all the rifles in the system, then they will show in stock. Everything currently showing on our site should either be in stock or coming in stock this week. Feel free to order/backorder through the link below, or give us a shout.”

LINK to TIKKA T3 RIFLE LIQUIDATION SALE

Tikka T3 sale inventory closeout reduction discount truckload

Models shown above are just part of the Sale Inventory. Nearly all Tikka T3 models are on sale.

Permalink Hot Deals, Hunting/Varminting, Tactical 2 Comments »
July 21st, 2016

New Rapid Ordering System for McMillan “Inlet Ready” Stocks

McMillan Fiberglass stocks inlet ready order free shipping retail store

With McMillan’s new “Inlet Ready” series of fiberglass stocks, you can get a customized McMillan stock in just two to four weeks. Use the web-based stock selector in McMillan’s online Retail Store.

To get to the Inlet Ready section, from the McMillan Home Page click “Retail Store“, then select “Stocks in Inventory” from the left-hand column. After clicking “Stocks in Inventory” from the left column, select “Inlet Ready” from the sub-menu. This video explains how to order your Inlet Ready stock for delivery in two to four weeks:

Get Free Shipping with Orders Over $400.00
Here’s another way you can save on purchases of McMillan stocks and shooting accessories. Go to McMillan’s online Retail Store. Choose stocks, bipods, gun cases, ammunition, apparel, triggers, and other items offered for sale. Then, during check-out, use Promo CODE mcm16. This will provide FREE Shipping if your total order is $400.00 or more.

NOTE: Free shipping applies to orders over $400, standard ground delivery in the Continental USA. Shipping charges on previous orders will not be reimbursed. This offer cannot be combined with other promotions or offers.

Product and Sale tip from EdLongrange. We welcome reader submissions.
Permalink Gunsmithing, Hot Deals No Comments »
July 17th, 2016

Getting Started in the Practical/Tactical PRS Game

65 Guys Ed Mobley Steve Lawrence PRS Precision Rifle Series Competition Tips

Have you been bitten by the PRS Bug? Our friends, Ed Mobley and Steve Lawrence, aka the “6.5 Guys”, have written an excellent article on getting started in practical/tactical competition. If you are new to the game, these tips can help you save money, progress faster, and have more fun. Here are article highlights, but we recommend you read the full story, 5 Tips for Attending Your First Precision Rifle Match, on www.65guys.com.

We often meet people who are new to long range precision shooting, and want to improve their knowledge and skill level. However, they aren’t sure if they are ready to sign up to compete in a match. They often ask, “What knowledge or skills are necessary to compete in a match?” Others may state, “I need to purchase this gear or that gear before I can attend a match”. For those guys who have a strong interest in precision rifle shooting, and who wish to check out a precision rifle match, below are Five Tips to make it a positive experience.

TIP ONE: Make Plans and Commit to Go

First you need to start by finding a match to attend. This may entail a little bit of research and investigative work on your part to find what matches are scheduled in the next few months. We recommend starting with any match that may be within a reasonable driving distance. This may likely be a local “club” match, many of which are held on a regular basis. These make great venues because it will provide an opportunity to meet some of the regular attendees as well as shooters that are from your geographic area. Additionally, most of the smaller matches are a little more relaxed in terms of level of competitiveness.

Once you decide on the match you want to attend, do your homework. This means finding out if you need to pre-register or pre-pay the match fee. Commit to going by registering for the match and putting it on your schedule. Be sure to find other useful information for questions such as:

— What time should I arrive?
— Is there a mandatory safety briefing for new shooters at that venue?
— What is the travel time required to get to the match site?
— How many stages will there be?
— Is there a description of the stages available before the match?
— How many rounds should you bring?
— Are there special equipment requirements? (E.g. do you need chamber flags, is there a pistol stage?)

65 Guys Ed Mobley Steve Lawrence PRS Precision Rifle Series Competition Tips

TIP TWO: Bring What You Have

(Don’t Spend a Fortune at the Start)
Some new shooters often assume they need a custom match rifle or all of the miscellaneous shooting gear associated with long range precision shooting to compete in match. While having a Kestrel weather meter and a high quality laser range finder and other shooting accoutrements are invaluable kit, you will find other shooters at your first match that will provide you with the information and coaching you need to get on target.

In fact, the only gear you really need to bring is a scoped rifle with a bipod and ammo capable of consistently shooting within one MOA. Also, be sure to know the ballistic drops or have a ballistic drop table prepared for your rifle/ammo to dial the correct DOPE on your scope for different target ranges. Many of the other participants at the match will be willing to let you borrow a support bag, bipod, tripod or other gear if you need one — just ask. Don’t use the excuse of not having the right gear to delay getting out to a match!

One reason not to make a big initial investment in a new rifle and assorted gear before competing, is we’ve seen a number of people come into the sport and try it for a year and then make the decision to move on to something else.

TIP THREE: Be Prepared to Learn

As a new shooter at a match, there is no better opportunity to learn. We often look to our local club matches as a group ‘training’ session to prepare for the bigger matches. You will find competitors at all levels of skill and many of your fellow shooters will enthusiastically provide helpful advice once they learn you are new to the sport. Take advantage of the opportunity to ask questions if you would like ideas for how to engage a stage, but also be sure to do more listening than talking as you receive guidance and tips from more experienced competitors.

Watch and observe other shooters and how they approach and ‘game’ a specific stage or course of fire. You’ll begin to recognize which shooting positions work best for different scenarios, and maybe even come up with some new ones that no one has thought of before.

Seeing what the better shooters do is an invaluable instructional tool. You can use your smart phone’s video camera to record other shooters (with their permission). When you’re ready to shoot, ask another shooter to record your performance. Watching yourself will point out needed areas of improvement.

65 Guys Ed Mobley Steve Lawrence PRS Precision Rifle Series Competition Tips

After each match conduct an informal after action review and summarize for yourself the things that went well and what you should continue to do. You should also identify the specific shooting skills you should develop and make a plan to integrate the appropriate practice drills into your practice sessions. Finally, if you maintain a shooter’s data book or journal you’ll want to note things such as:

After Action Review – How you did, what went well, things you need to work on in practice.
Stage Observations – Successful methods used for specific courses of fire. Note barricades, positions used, specific gear used for stages.
Gear Observations – How your rifle/gear performed, what new items you should add to your “buy list”.

TIP FOUR: Be Safe and Have Fun

You’ve all heard a parent or teacher say, “It’s all fun and games until someone loses an eye.” The same can be said of the shooting sports. Safe handling of firearms is the number one rule at any match, and comes before the FUN part in terms of importance.

Before all matches start there will always be some form of a mandatory safety briefing. Make sure you know, understand, and follow any unique safety protocols for the match you attend. Some matches require all rifles have chamber flags inserted and are stowed in bags/cases while not on the firing line — other matches may not. If you run afoul of any safety rules, you risk the chance of being disqualified from a stage or worse, the entire match.

65 Guys Ed Mobley Steve Lawrence PRS Precision Rifle Series Competition Tips

The second rule is simply have fun. This starts with having a good attitude throughout the day. Keep in mind that as a new competitor you should think of a match as a solid day of practice and training. If you blow a stage, use it as an opportunity to diagnose what you could have done differently or what you need to improve on — then smile and drive on.

Any day at the range or shooting is a good day. A match is an opportunity to hang out with like-minded people who are passionate about shooting and impacting targets far-far away. Life is great when you are doing what you enjoy!

TIP FIVE: Make Friends

There is no better way to meet lots of precision rifle shooters and make friends than at a match. The people that attend the tactical precision matches on a regular basis are those that have ‘fallen into the deep end of the pool’ and are really into the sport. As a result, they have become part of the local precision shooting community. As you strike up conversations at the match, find out if your new-found friends visit specific forum boards or social media outlets, or if there are other matches they attend.

Precision shooters tend to congregate and share information in different corners of the Internet. It will serve you well to meet some of the guys in person at matches and be able to connect a face to a screen name. As you develop your friendships and develop a level of trust, you will find opportunities become available to shoot with others in your local area, or get ‘read-in’ on a secret honey-hole of a spot to shoot long distance. Additionally, the local shooting community will often find it more convenient to sell or trade gear and equipment locally than deal with buyers/sellers that are out of state.

>> CLICK HERE to READ FULL ARTICLE on 65Guys.com

Permalink - Articles, Competition, Tactical No Comments »