Eurooptic vortex burris nightforce sale




teslong borescope digital camera barrel monitor


As an Amazon Associate, this site earns a commission from Amazon sales.









January 2nd, 2020

TEN Worst Reloading Mistakes — Do You Agree with This List?

Shooting Times Reloading Failures Mistakes Top Ten 10

Last fall, Shooting Times released an article entitled “Ten Most Common Reloading Mistakes”. Listed below are the Top Ten mistakes hand-loaders can make, at least according to Shooting Times. What do you think of this list — does it overlook some important items?

Top Ten Reloading Mistakes According to Shooting Times:

1. Cracked Cases — Reloaders need to inspect brass and cull cases with cracks.

2. Dented Cases — Dents or divets can be caused by excess case lube.

3. Excessive Powder Charge — Overcharges (even with the correct powder) can be very dangerous.

4. Primers Not Seated Deep Enough — “High” primers can cause functioning issues.

5. Crushed Primers — Some priming devices can deform primers when seating.

6. Excess Brass Length — Over time, cases stretch. Cases need to be trimmed and sized.

7. Bullets Seated Too Far Out — If the bullet is seated too long you may not even be able to chamber the round. Also, with hunting rounds, bullets should not engage the rifling.

8. Burrs on Case Mouths — Ragged edges on case mouths can actually shave bullet jackets.

9. Excess Crimp — This is a common problem with pistol rounds loaded on progressives. If case lengths are not uniform some cases will get too much crimp, others too little.

10. Inadequate Crimp — This can be an issue with magnum pistol cartridges in revolvers.

Do you agree with this list? We think some important things are missing, such as not adjusting full-length sizing dies properly. This can cause the shoulder to be pushed back too far (or not far enough). Another common mistake is using brass that is worn out, i.e. stretched in the case-head area from multiple cycles of hot loads. We also think the #1 error a reloader can make is using the wrong powder altogether. That can be a fatal mistake. See what happens when you load pistol powder in a rifle.

Permalink Bullets, Brass, Ammo, Reloading 13 Comments »
December 23rd, 2015

Top 10 Reloading Fails — Do You Agree?

Shooting Times Reloading Failures Mistakes Top Ten 10

Shooting Times has released an article entitled “Ten Most Common Reloading Mistakes”. Listed below are the Top Ten mistakes hand-loaders can make, at least according to Shooting Times. What do you think of this list — does it overlook some important items?

Top Ten Reloading Mistakes According to Shooting Times:

1. Cracked Cases — Reloaders need to inspect brass and cull cases with cracks.

2. Dented Cases — Dents or divets can be caused by excess case lube.

3. Excessive Powder Charge — Overcharges (even with the correct powder) can be very dangerous.

4. Primers Not Seated Deep Enough — “High” primers can cause functioning issues.

5. Crushed Primers — Some priming devices can deform primers when seating.

6. Excess Brass Length — Over time, cases stretch. Cases need to be trimmed and sized.

7. Bullets Seated Too Far Out — If the bullet is seated too long you may not even be able to chamber the round. Also, with hunting rounds, bullets should not engage the rifling.

8. Burrs on Case Mouths — Ragged edges on case mouths can actually shave bullet jackets.

9. Excess Crimp — This is a common problem with pistol rounds loaded on progressives. If case lengths are not uniform some cases will get too much crimp, others too little.

10. Inadequate Crimp — This can be an issue with magnum pistol cartridges in revolvers.

Do you agree with this list? We think some important things are missing, such as not adjusting full-length sizing dies properly. This can cause the shoulder to be pushed back too far (or not far enough). Another common mistake is using brass that is worn out, i.e. stretched in the case-head area from multiple cycles of hot loads. We also think the #1 error a reloader can make is using the wrong powder altogether. That can be a fatal mistake. See what happens when you load pistol powder in a rifle.

Permalink Reloading 16 Comments »