Eurooptic vortex burris nightforce sale




teslong borescope digital camera barrel monitor


As an Amazon Associate, this site earns a commission from Amazon sales.









February 18th, 2014

Hodgdon Launches Completely Revamped Reloading Center

Hodgdon Reloading data Center hand loading powderHodgdon has rolled out a completely updated online Reloading Data Center for pistol, rifle, and shotgun reloaders. Check out the enhanced Data Center at www.HodgdonReloading.com.

As before, you’ll find thousands of load recipes for pistol, rifle, and shotgun. Rifle shooters will find dozens of loads for their favorite Hodgdon, IMR, and Winchester powders such as H4198, Varget, H4350, and IMR 8208 XBR. And Hodgdon’s Reloading Center is now faster and easier to use. Navigation is simplified and the whole interface is more user-friendly.

Hodgdon Reloading data Center hand loading powder

You’ll notice changes in the way the online Data Center works. Now you have more control over the results. After choosing a cartridge, you can pre-select specific bullet weights and powder types. That quickly delivers just the information you want and need. You won’t have to scroll through scores of entries for bullets or powders you don’t use.

Hodgdon Reloading data Center hand loading powder

Mobile users will notice that the updated/enhanced Reloading Center is much more “user-friendly” for smart-phone and tablet users. Controls have been optimized for touch-screens, and buttons are large and easy to use. Likewise the results are displayed in a large, easy-to read format.

Hodgdon tip from EdLongrange. We welcome reader submissions.

Permalink News, Reloading 7 Comments »
February 18th, 2014

New Bore-Tips Foam Bore Swabs for Barrel Cleaning

Wouldn’t it be nice to dispense with patches and jags when cleaning your guns? The folks at Super Brush, LLC, had the same idea, so they invented Bore-tips® swabs. These reusable foam “mops” provide 360° of contact with the bore, reaching both the grooves and the lands. Bore-tips thread onto standard cleaning rods. They are offered in a variety of sizes, from .22 Caliber up to 12 Gauge. Rifle Bore-tips come in .22 (5.56mm), .243 (6mm), and .308 (7.62mm) diameters.

Bore-tips foam bore swab

We saw samples of this new product for the first time at the Berger SWN. We’re intrigued. The product may be useful for some applications, particularly pistols and shotguns which require minimal brushing. For rifles they do a good job of applying solvents because they hold more liquid than a patch. However, you probably won’t want to abandon your jags and patches. Sometimes a tight-fitting patch is still the best tool for the job. Patches are cheap and it’s easier to discard a used patch, rather than fuss with cleaning foam swabs. But for shotguns (and lightly used pistols), these things make sense.

Bore-tips® Claimed Benefits:
• Each tip is reusable and can be cleaned with solvents or soap and water.
• Tough and fiber-free, Bore-tips will not shed or leave lint behind as cotton will.
• FAST PATCHLESS CLEANING — solves the shortcomings of the jag and patch.
• Foam fills the lands and grooves of the rifling, not sliding over the top like a patch.
• Quick threading on a standard 8-32 cleaning rod. Shotgun sizes use a 5/16 x 27 rod.
• Can be used with most commercially available solvents and oils.

How to Use Bore-tips®
Bore-tips foam bore swab
Use a Bore-tip to apply solvent to the barrel. After allowing the solvent time to work, brush the bore to break up any fouling. Next use a clean Bore-tip to push the fouling out the bore. When the now dirty Bore-tip clears the bore, wet it with a little solvent and then squeeze it with an absorbent rag or paper towel, this will blot the dirt off. After blotting the Bore-tip should be clean enough to continue using to remove the fouling until you are finished cleaning. When you are satisfied with the cleanliness of your barrel, use a clean Bore-tip to dry the bore.

Click for Full-Screen Images
Bore-tips foam bore swab Bore-tips foam bore swab

How to Clean Bore-tips®
Bore-tips foam bore swab
For faster cleaning, apply mineral spirits to the Bore-tip and squeeze/blot into an absorbent rag or paper towel. When the Bore-tip is clean, let dry and reuse. Using soap and water, squeeze to blot out any excess solvent or dirt. Next, wash the Bore-tip with a grease-cutting soap and warm water. Once clean, rinse then let dry completely. See cleaning video below:

Bore-Tips Foam Swab Cleaning Demonstration

Permalink Gear Review, New Product 5 Comments »