Rimfire Barrel Cleaning — ELEY’s Recommended Methods
Here’s a record-setting rimfire benchrest rifle owned by our friend Joe Friedrich.
The experts at ELEY Limited, top rimfire ammo-maker, have posted a helpful guide to cleaning rimfire barrels. We reprint highlights of the article below, but we suggest you read the full article on the Eley website: How to Clean Your Rifle the ELEY Way.
Editor’s Comment: This is not the only way to clean a rimfire barrel. There are other procedures. This is the method recommended by ELEY based on decades of experience with the top smallbore shooters in the world, including many Olympic Gold Medalists. Some shooters have been very successful cleaning less frequently, or using different types of solvents. The ELEY method is a good starting point.
Rimfire Barrel Cleaning
1. Clean the extension tube with a 12 gauge brush and felt or tissue moistened with solvent.
2. Smoothly insert a cleaning rod guide into the receiver.
3. Apply a dry felt to the cleaning rod adapter and push it through the barrel to the muzzle in one slow steady movement. As the felt is dry it may feel stiff.
4. Remove the soiled felt and pull back the cleaning rod.
5. Apply a new felt to the cleaning rod adapter and moisten it with Rimfire Blend / cleaning oil.
6. Insert the moistened felt into the barrel and push it to the muzzle with short forward movements.
7. Remove the soiled felt and pull back the cleaning rod through the barrel.
8. Clean the rod with tissue to avoid getting solvent on your hands.
9. Repeat steps 6, 7 and 8, until the felts are no longer dirty or soiled.
10. After steps 1-9, Eley recommends running an oiled felt down the bore. Before the next use of your rifle use a cleaning rod to push a clean dry felt through the barrel to the muzzle in one steady movement. Repeat this until there are no signs of oil on the felt.
Clean More Thoroughly After 200-300 Rounds
IMPORTANT: Eley stresses that the procedure outlined above is a basic cleaning procedure. After a few hundred rounds, Eley recommends brushing the barrel to remove lead deposits:“Intensive cleaning of your rifle will be needed after every 200–300 rounds. The barrel should be cleaned with a bronze brush. In order to do this you will need to push the brush in the direction of the muzzle and repeat three times. A bronze brush is used as it is the only tool that can be used to completely remove lead remnants.”
The above procedure is reprinted courtesy ELEY. All content © 2015 ELEY Limited. All rights reserved. Do not reproduce without written permission.
Similar Posts:
- How to Clean Your Rimfire Rifle Barrel the ELEY Way
- You Need to Do More Than Just Clean the Inside of Your Barrel
- TECH TIP: Clean Your Chamber and Lug Recesses
- Cleaning the Inside of Lug Recesses and Chamber Area
- Tech Tip: Don’t Forget to Clean Your Chamber and Lug Recesses
Share the post "Rimfire Barrel Cleaning — ELEY’s Recommended Methods"
Tags: .22 LR, Barrel, Cleaning, Eley, Felt, Lead Remover, Rimfire, Smallbore, Tenex
My nylon brush does just as well, and yields no wear on muzzle or rifling. In fact, none of my barrels get bronze brushes anymore.
Hi guys..
“In fact, none of my barrels get bronze brushes anymore.”
Same for me !
Best regards form Switzerland
Florian
With over 30 years of competitive shooting, in my experience, bronze brushes cause NO barrel wear. The vast majority of Bench rest shooters use them and they are the most effective barrel cleaner.
However, if one chooses not to use them and your present method of cleaning your barrel works for you, then that’s fine. But, don’t imply that bronze brushes hurt rifle barrels with no evidence.
Read where Anschutz, for many of their target 22’s recommend cleaning your barrel every 3,000 to 10,000 rounds.
My take,
Clean the barrel If you want to.
If your rifle is maintaining accuracy don’t bother.
But, do keep the action clean and lubricated.