Don’t Kill the Chrono! Setting up Chronos to Avoid Stray Shots
There is nothing more frustrating (or embarassing) than sending a live round into your expensive new chronograph. As the photo below demonstrates, with most types of chronographs (other than the barrel-hung Magnetospeed), you can fatally injure your expensive chrono if it is not positioned precisely.
When setting up a chrono, we always unload the rifle, remove the bolt and bore-sight to ensure that the path of the bullet is not too low. When bore-sighting visually, set up the rifle securely on the sandbags and look through the bore, breech to muzzle, lining up the barrel with your aim point on the target. Then (during an appropriate cease-fire), walk behind the chronograph. Looking straight back through the “V” formed by the sky-screens, you should be able to see light at the end of the barrel if the gun is positioned correctly. You can also use an in-chamber, laser bore-sighter to confirm the visual boresighting (see photo).
Adjust the height, angle and horizontal position of the chronograph so the bullet will pass through the middle of the “V” below the plastic diffusers, no less than 5″ above the light sensors. We put tape on the front sky-screen supports to make it easier to determine the right height over the light sensors.
Use a Test Backer to Confirm Your Bullet Trajectory
You can put tape on the support rods about 6″ up from the unit. This helps you judge the correct vertical height when setting up your rifle on the bags. Another trick is to hang a sheet of paper from the rear skyscreen and then use a laser boresighter to shine a dot on the paper (with the gun planted steady front and rear). This should give you a good idea (within an inch or so) of the bullet’s actual flight path through the “V” over the light sensors. Of course, when using a laser, never look directly at the laser! Instead shine the laser away from you and see where it appears on the paper.
Alignment of Chronograph Housing
Make sure the chrono housing is parallel to the path of the bullet. Don’t worry if the unit is not parallel to the ground surface. What you want is the bullet to pass over both front and rear sensors at the same height. Don’t try to set the chrono height in reference to the lens of your scope–as it sits 1″ to 2″ above your bore axis. To avoid muzzle blast interference, set your chronograph at least 10 feet from the end of the muzzle (or the distance recommended by the manufacturer).
Rifles with Elevated Iron Sights
All too often rookie AR15 shooters forget that AR sights are positioned roughly 2.4″ above the bore axis (at the top of the front sight blade). If you set your bullet pass-through point using your AR’s front sight, the bullet will actually be traveling 2.4″ lower as it goes through the chrono. That’s why we recommend bore-sighting and setting the bullet travel point about 5-8″ above the base of the sky-screen support shafts. (Or the vertical distance the chronograph maker otherwise recommends). NOTE: You can make the same mistake on a scoped rifle if the scope is set on very tall rings, so the center of the cross-hairs is much higher than the bore axis line.
TARGET AIM POINT: When doing chrono work, we suggest you shoot at a single aiming point no more than 2″ in diameter (on your target paper). Use that aiming point when aligning your chrono with your rifle’s bore. If you use a 2″ bright orange dot, you should be able to see that through the bore at 100 yards. Using a single 2″ target reduces the chance of a screen hit as you shift points of aim. If you shoot at multiple target dots, place them in a vertical line, and bore sight on the lowest dot. Always set your chron height to set safe clearance for the LOWEST target dot, and then work upwards only.
Other Chronograph Tips from Forum Members:
When using a chronograph, I put a strip of masking tape across the far end of the skyscreens about two-thirds of the way up. This gives me a good aiming or bore-sighting reference that’s well away from the pricey bits. I learned that one the hard way. — GS Arizona
A very easy and simple tool to help you set up the chronograph is a simple piece of string! Set your gun (unloaded of course) on the rest and sight your target. Tie one end of the string to the rear scope ring or mount, then pull the string along the barrel to simulate the bullet path. With the string showing the bullet’s path, you can then easily set the chronograph’s placement left/right, and up/down. This will also let you set the chrono’s tilt angle and orientation so the sensors are correctly aligned with the bullet path. — Wayne Shaw
If shooting over a chrono from the prone position off a bipod or similar, beware of the muzzle sinking as recoil causes the front of the rifle to drop. I “killed” my first chronograph shooting off a gravel covered firing point where I’d not given enough clearance to start with and an inch or two drop in the muzzle caused a bullet to clip the housing. — Laurie Holland
Similar Posts:
- Setting up your Chronograph–Remember It’s a Tool, Not a Target
- Range Tip: How to Avoid Blasting Your Chronograph
- How NOT to Ventilate Your Chronograph — Set-Up Tips
- Chrono No-Nos: Remember this Device is a Tool, Not a Target
- How NOT to Ventilate Your Costly Chronograph — Set-UP Tips
Share the post "Don’t Kill the Chrono! Setting up Chronos to Avoid Stray Shots"
Tags: Boresighting, Chrono, Chronograph, Laser Bore-Sight, Magnetospeed, safety, Shooting Chrony, Tripod
Ah, just shoot your old chorono and get a lab radar.
Nice post. Very helpful and thanks for sharing
Hello to TirMaillyForum!
Any time that I am unsure about my rifle’s alignment with a chronograph, after sighting in on the target, with the bolt removed, I look down the bore, to make sure that I do not see something that I do not want to hit. Most of the time this is not an issue but with fixed power scopes of high power it can be very difficult to see where you are from behind the rifle. This saved some damage one time, and that made it worth the time that it takes.
I use a shooting chrony and put an inch of survey ribbon at the joint of the 4 rods that hold up the sun shade. It helps me see if the chrony is lined up straight and also once set up I can clearly see the tape in relation to the the cross hairs on low power. If the gun is all lined up I just turn the power up and shoot:)
Somehow I find the more expensive the chrono the easier it is for me to shoot.
Tired some BC testing at 1000 yards one day. The only chrono parts exposed to bullets were the rods and shades on top. Only took us 3 rounds to destroy that.
I really want a chrono small enough to mount directly on the X ring of the 1000 yard highpower target. No doubt I’d be in for a big score that day.