Think you can shoot fast with a bolt gun? Bet you can’t beat these Norwegian speed-demons. Inge Hvitås recently set a new Mad Minute World Record, putting 39 rounds inside a 16″ circle at 200 meters, all in a single minute. Another Norwegian ace fired 48 rounds in a minute, with 38 in the bullseye. Now that’s spectacular speed and accuracy.
Watch Inge Hvitås Set New Mad Minute World Record:
New Mad Minute World Record — 39 Hits in One Minute (60 seconds)
At the Haga shooting range in Norway, spectators witnessed spectacular speed shooting earlier this month. On June 4th, Norwegian shooter Inge Hvitås set a new Mad Minute Challenge World Record with 39 hits in ONE MINUTE at 200m. The target was a 40cm (15.75″) bullseye placed at 200m (218 yards). Fellow Norwegian Jesper Nilsstua also shot brilliantly, sending 48 rounds down-range in one minute. Jesper had 38 hits, missing the record by just one. Both shooters were using iron-sighted Sauer 200 STR target rifles, which are normally chambered for the 6.5×55 cartridge. For this event, magazines are limited to 5 rounds and shooters may use slings but no bipods or other support.
Amazing Bolt-Gun Cycling Speed — 48 Rounds in One Minute
Another Norwegian ace, Jesper Nilsstua, missed the Mad Minute Challenge record (by one hit), but boy was he fast. Dennis Santiago (who has done his own Mad Minute drill), was dazzled: “This dude didn’t get the new world’s record of 39 hits in 60 seconds. He ‘only’ got 38 hits after getting off an amazing 48 shots in 60 seconds. Watch the smoothness of his shooting. It’s amazing.”
For the Mad Minute Challenge in Norway, a standard 200m DFS target was used, with 1 point per hit within the black area which is 40cm (15.75″, or 6.9 MOA) in diameter.
Norwegian Mad Minute Challenge — Event Rules
The organizers of the event posted: “The Mad Minute Challenge [is] a modern edition of a old military drill. This is a place for sport shooters to … share experiences on the subject of speed shooting with bolt-action rifles. The Mad Minute Challenge is all about the sport! To make a attempt for the record everyone must follow these five simple rules:”
About the Original MAD MINUTE
“Mad Minute” was a pre-World War I term used by British Army riflemen during training at the Hythe School of Musketry to describe scoring a minimum of 15 hits on a target at 300 yards within one minute using a bolt-action rifle (usually a Lee-Enfield or Lee-Metford rifle). It was not uncommon during the First World War for riflemen to greatly exceed this score. The record, set in 1914 by Sergeant Instructor Alfred Snoxall, was 38 hits.
Listed as “Practice number 22, Rapid Fire” of The Musketry Regulations, Part I, 1909, this drill required at least 15 shots on the Second Class target at 300 yards. The exercise was just one of several annual tests to classify a soldier as a sharpshooter, first or second class shooter depending on the points achieved.
Research indicates the Second Class target was a 48″ x 48″ square with 24″ inner circle and 36″ outer circle. The sight mark was a central 12″ x 12″ shape representing a soldier. ALL hits scored points (3 for center circle, 2 for outer circle, 1 for outer square). NOTE: Though some sources say the Mad Minute drill used a 12″-diameter round target, this appears to be a mistake from Ian Hogg’s book “The Encyclopedia of Weaponry”. No other source mentions a 12″ circle, which would be a mere 3.82 MOA. In reality the true drill target was a 48″ x 48″ square, roughly 15 times larger. (From No.WikiPedia.)
34th Annual Fifty Caliber Championship Coming Soon
The 34th Annual Fifty Caliber Shooters Association (FCSA) 1000/600 Yard World Championship will be held July 4, 5 and 6, 2019 at the Whittington Center in Raton, New Mexico, a beautiful facility. The FCSA Championship takes place right after the 2019 King of 2 Miles event, running June 29 – July 1, 2019.
Looking downrange at the 1000-yard line. Note the fan and air hose for cooling the barrel.
Competitor’s POV perspective from a FCSA Match. Note the mirage.
By James Patterson This article first appeared in Sinclair International’s Reloading Press Blog
For a number of years I drooled over every .50 BMG caliber rifle that I came across, I read every article I could find and determined that ‘Someday’ I was going to have one. Well I finally took the plunge and in 2002 I purchased my first ‘Big 50’. Almost immediately I joined the Fifty Caliber Shooters Association (FCSA) and I have since come to immensely enjoy shooting this challenging cartridge and associating with some of the best people on earth.
FCSA Founded in 1985 The FCSA, started in 1985, is an international organization with members in 22 countries. Headquartered in Monroe, Utah, the FCSA has a membership of approximately 4000. While the FCSA provides a service to military and law enforcement with research and instruction as well as an active liaison in both communities, the primary charter of the FCSA is the promotion of the sporting use of the 50 BMG cartridge and its wildcat derivatives. It has been the FCSA and its members who have lead the way in refining .50-caliber cartridges, rifles, and 1000-yard plus shooting know-how. Members enjoy a quarterly magazine, a suppliers directory, an active website with great photo galleries, and access to literally the best repository of 50 BMG information on the planet. If you are interested in Mr. John Browning’s big 50, you should seriously consider joining the FCSA.
This interesting .50 Cal rig features a liquid-cooled barrel and unusual scope mounting arrangement.
While all aspects of the 50 BMG are promoted by the FCSA, the primary sport is 1000-yard competition. In 2010, there were 16 separate official matches scheduled across the USA, and many more ‘fun-shoots’. This sport is an incredible mix of the science, skill, and art of extreme long range accuracy. I had been actively shooting rifles and hunting for well over 40 years and had always considered myself a “rifle man”. But I had no idea of the learning curve that [faced me] when I first joined the FCSA.
Historically, 1000-yard shooting has been primarily a benchrest activity but in the past several years we have seen a tremendous interest in ‘Hunter Class’ competition; this is shot prone using a bipod. This form of long range match shooting is excellent preparation for long range hunting. The required skill set [for ultra-long-range hunting] is guaranteed to humble even the most experienced rifleman.
Cost of Big-Bore Shooting
Is owning and shooting a 50 BMG caliber rifle expensive? Relatively speaking yes, but one must put it into perspective. Rifles may run from $2500 to $8000, maybe even more for a top of the line custom rifle. A premium long-range scope will set you back $1800 to $3500. And while excellent .50 BMG commercial ammo is available, it runs $5 to $6 per round! Most serious shooters start reloading for the rifle as soon as practical, not only for the economics of reloading but also for the ability to fine tune custom ammo for their specific rifle. It’s a very rare match that is won shooting commercial ammo.
This is just one example. This deal works with ANY Lapua bullets purchased from Grafs.com. You can mix and match, as long as you buy at least $100 worth of Lapua bullets.
Lapua makes great bullets. Bryan Litz writes great books. And now you can get both with this special promotion from Graf & Sons. Here’s the deal — if you buy at least $100.00 worth of Lapua bullets at Grafs.com, you’ll get a free Applied Ballistics book authored by Bryan Litz.
You can mix and match any types of Lapua bullets — as long as the bullet order totals $100.00 or more. The book may be one of various Litz titles, such as Modern Advancements in Long Range Shooting or Ballistic Performance of Rifle Bullets. NOTE: You do NOT get to pick the book title — you get what’s available. You want to move quickly on this deal — books are limited to supply on hand.
If you order now, you can get the bullets to shoot, and give the book to Dad for a late Father’s Day gift.
Lapua Bullets — Accuracy & Consistency If you haven’t tried Lapua bullets yet you should. The Scenar-L bullets we have tested have proven extremely consistent in weight and base-to-ogive measurement.
And they shoot. We have a couple rifles that prefer Scenars over all other match bullets we have tried. We have won club matches with the 6mm Scenar-L 105s in a 6mmBR, while the 6.5mm 123gr Scenar and 136gr Scenar-L work superbly in our 6.5 Creedmoors.
Another legislative attack on the firearms industry is being pushed in Congress by Democratic party politicians. Rep. Adam Schiff (D-CA) and Sen. Richard Blumenthal (D-CT) reintroduced legislation this week that targets the gun industry, allowing persons to sue the makers of firearms that were used by criminals to cause injury. Currently, such lawsuits are blocked by the Protection of Lawful Commerce in Arms Act (PLCAA) enacted in 2005.
The new Democratic legislation, the “Access to Justice for Victims of Gun Violence Act”, would repeal the PLCAA. If the PLCAA is repealed, then gun-makers could potentially be sued for the actions of criminals using firearms — even if the guns were stolen. If bad guys cause harm with guns, the Democrats want the gun-makers to pay, and keep paying. The goal is to eventually bankrupt the gun industry and put companies such as Colt, Ruger, and Smith & Wesson out of business.
The Democrats have gone after the PLCAA before. NPR reports: “The effort to repeal PLCAA by Democrats on Capitol Hill is not new. Schiff first introduced the measure in 2013, and it has been reintroduced at least two other times without gaining traction.”
The real goal of this legislation is to cripple the gun industry. GunAmerica Digest explains: “One of the primary goals of anti-gunners is to bankrupt the gun industry by repealing the Protection of Lawful Commerce in Arms Act (PLCAA).”
The sponsors of the new legislation claim their legislation is needed to protect citizens. Congressman Schiff (D-CA) declared: “This bill would pierce the gun industry’s liability shield by putting an end to the special protections the gun industry receives when they shirk their fundamental responsibility to act with reasonable care for the public safety.”
GunsAmerica Digest says don’t believe this: “Schiff and Blumenthal are grossly mis-characterizing the purpose of PLCAA. It does NOT protect members of the gun industry from product liability suits for manufacturing or design defects or certain types of negligent conduct. It merely prohibits lawsuits against gun makers for damages resulting from the third-party criminal misuse of their firearms.”
It’s clear what the sponsors of this legislation really want. They seek to destroy the U.S. gun industry through waves of lawsuits — “death by 1000 cuts”. The anti-gunners may not be able to remove the Second Amendment from the Bill of Rights, but if they succeed in bankrupting all the major gun-makers, then the “Right to Keep and Bear Arms” won’t be worth much.
Practical/Tactical fans, mark your calendars. The Precision Rifle EXPO is back for its second year, running September 28-29, 2019 at the Arena Training Facility in Blakely, Georgia. Last year, over 800 attendees came to the two-day event. This year, manufacturers will be showing off actions, optics, ammo, reloading equipment, stocks, chassis, electronics, supporting equipment (bags and tripods), rifles, triggers, suppressors, and much more. There will be training sessions on precision handloading, wind reading, marksmanship, ballistic devices, and introduction to competition.
The event lets precision rifle enthusiasts connect with top manufacturers, rifle instructors, and leading tactical competitors. You can Pre-Register for $35, or pay $50 at the door in September. Registration includes access to the exhibition tent and the range locations, plus the educational classes for both days.
Video Showcases Last Year’s Precision Rifle EXPO:
All Types of Products Will Be on Display
The Precision Rifle EXPO offers a unique opportunity to check out the latest products from dozens of top companies all in one place. We expect over 40 companies will be at the EXPO, displaying complete rifles, actions, triggers, stocks, optics, reloading gear, ammo, electronics, rangefinders, chronographs, ear protection, support bags, bipods, tripods, and all manner of accessories.
Nick Gadarzi in Utah NRL match with Leupold Mark 5HD™ 5-25×56mm, TMR reticle
Precision Rifle EXPO 2018 Exhibitor List
NOTE: There may be some changes for 2019, but there should still be 40+ Exhibitors.
Accurate Ordnance
Alpha Munitions
Atlas (B&T Industries)
Area 419
Armageddon Gear
Barrett
Berger
Bushnell
Cole-TAC
Curtis Custom
Defiance
Federal
GA Precision
Hunts Long Range
Kahles
Kelbly’s
Kestrel
Knights Armament
Lapua
Magnetospeed
Manners Stocks
MasterPiece Arms
McMillan Stocks
McWhorter Rifles
MDT Chassis
Nightforce
Proof Research Barrels
RCBS
Really Right Stuff
Rugged Suppressors
Schmidt & Bender
Sierra
SK Ammo
Stillers Precision
Swarovski
Timney
Trigger Tech
Vortex
Vudoo Rifles
Warnes Scope Mounts
West Texas Ordnance
Whidden Gun Works
Arena Training Facility — 2300 Acres
The 2300-acre Arena Training Facility is a premier shooting facility with multiple shooting ranges from 50m to 2100m. Arena’s 1000-yard covered Known Distance range offers multiple benches, steel and paper targets out to 1000 yards. On Arena’s UKD (unknown distance) range shooters can engage steel out to 2300 yards. This 2100m UKD range boasts a 3-Story Shooting Tower, Air-Conditioned Shoot House, and multiple Positional Challenges.space.
The Arena Training Facility is located approximately two hours from the Hartsfield Airport in Atlanta, Georgia and is centrally located in the Southeastern USA.
Rifle accuracy is pointless unless you can see your target and aim precisely. That’s why good optics are so important for precision shooting — from 50 yards out to a mile and beyond. Today’s premium scopes can be very expensive — you’ll see optics costing $3000 or more on many competition F-Class and PRS rifles. This article covers important “Riflescope Knowledge”, including how to adjust for parallax, and how to properly sight-in your scoped rifle. In addition there’s a helpful video defining Minute of Angle (MOA) plus two videos showing how to mount scopes.
Rifle Sight-In Process — Start to Finish
Here Ryan Cleckner shares his process for sighting in a scoped rifle. This helpful video covers the full process: bore-sighting, 25-yard shot confirmation, shooting groups, making adjustments at 100 yards, and finding mechanical zero. Looking for more valuable rifle instruction? Then check out Ryan Cleckner’s book, Long Range Shooting Handbook.
How to Adjust for Parallax
Most precision rifle scopes have parallax adjustment, but what is it and why do you need to adjust it? In this Shooting USA video, John Paul of JP Rifles defines parallax and explains why you need to set parallax correctly for the distance to your target. The video then show how to adjust parallax correctly. a process which should start with the scope’s ocular focus.
Understanding Minute of Angle (MOA)
In this video, Ryan Cleckner explains the measurement term “minute of angle” (MOA) and how to use MOA adjustments on your scope to compensate for bullet drop at varying distances. MOA is an angular measurement, used often in long range shooting, that is 1/60th of one degree of a circle. One MOA represents 1.047″ at 100 yards and 10.47″ at 1000 yards. Want to learn more? Read Ryan Cleckner’s article Understand and Using Minute of Angle.
How to Mount a Riflescope
When mounting a scope you want to use quality rings, and ensure that the scope is leveled properly. In addition, you need to adjust the fore/aft position of the scope so that eye relief is correct. Ideal scope position may be different when shooting from the bench vs. shooting prone. In this Shooting USA video John Paul of JP Rifles reviews scope mounting basics.
Scope Mounting on a PRS Precision Rifle
Here the MasterPiece Arms (MPA) Academy experts show how to mount a scope on a PRS-type tactical rifle. Special considerations for tactical shooters are discussed. The video also shows recommended tools for scope mounting operations.
In response to a Bulletin story about Norma powders at Midsouth Shooters Supply, one of our Forum members asked: “I’m having trouble finding Reloder 15 for my 6.5×47 Lapua — should I consider running Norma 203B instead?” As we’ve explained before, these two powders, both made by Bofors in Europe, are very, very similar. Here are some hard numbers that should demonstrate how virtually identical these powders really are.
Target Shooter Magazine writer Laurie Holland compared Norma 203B and Reloder 15 using data from QuickLOAD. Laurie also checked load manuals to see how listed charge weights varied for the two propellants. Laurie concluded there was very little difference between Norma 203B and Reloder 15.
Norma 203B vs. Alliant Reloder 15 Commentary by Laurie Holland
Running [203B and RL15] through QuickLOAD doing a ‘charge table’ run for a 130gn Berger VLD at 2.700 COAL in 6.5X47 Lapua, gives very similar positions in the table [for both powders]. The charge required to achieve 62,000 psi estimated pressure varies by a mere 0.2 grains between the pair, Norma 203B being the heavier of the two. The estimated Muzzle Velocity (MV) also varies by a mere 2 fps, RL15 estimated to produce 2,946 fps MV compared to 2,944 fps for N203B at 62,000 psi (with the parameters I used).
If they aren’t the same thing, they’re so close as to make no difference and as Forum Boss points out, they’re made by the same people (Bofors) in the same plant.
[The Berger Reloading Manual includes data for both powders] for the .308 Winchester and heavier bullets (185 to 230 grains). Maximum charges and claimed MVs are not always identical, but are so close as to be marginally different production lots of the same thing, or maybe the result of minor testing variations.
.308 Win Max Charge Weights in Grains (RL15 / N203B) (Berger Manual)
MVs [for the four bullet types] are close but not identical, the largest difference being for the 210s which shows RL15 producing 2,428 fps MV v 2,383 for Norma 203B.
Norma 203B Chemistry
According to the Norma Reloading Handbook #1, Norma 203B has the following composition:
85% Nitrocellulose
7.5% Nitroglycerin
2.0% surface coating
4.6% Various chemicals
0.9% Water
3,957 J/g specific energy
890 g/l specific density
For comparison, the 7.5% NG component compares to 15% in Viht N500 series powders and 10% in Ramshot TAC / Big Game / Hunter.
This is big news for anyone who spots for a fellow shooter. Nikon has introduced new RETICLE EYEPIECES for spotting scopes. Having a reticle eyepiece with precise hashmarks allows the spotter to make wind calls, recommend hold-offs, and give precise click recommendations for follow-up shots. On Nikon’s new eyepieces, integral FS-MRAD or FS-MOA glass-etched reticles include precise milling scales for highly detailed measurements of targets. Nikon’s new MEP-30 Reticle Eyepieces, priced at $449.95 each, provide 30X magnification on 82mm spotting scope bodies and 24X on 60mm bodies.
MRAD and MOA Reticle Eyepieces Fit Straight or Angled Body
For its flagship Monarch Fieldscopes, Nikon offers the new MEP-30 Reticle Eyepieces, with either MRAD or MOA reticles, priced at $449.95. Both reticle types allow a person spotting to locate/focus on the same target as his counterpart to communicate reference points and follow-up corrections. For example, someone watching shot impact could immediately report: “You’re hitting 2 MOA low — add 8 clicks elevation.” (E.g. for a scope with 1/4-MOA clicks).
About the MEP-30 Eyepieces
Nikon states: “The Field Flattener Lens System in the new MEP-30 eyepieces provide exceptional edge-to-edge clarity, resolution, life-like color and contrast. The new eyepieces feature a type-1 bayonet mount for simple and secure attachment to the MONARCH Fieldscope body. Like the Fieldscope body, the eyepieces are waterproof and fogproof (when attached to the body).”
Ace tactical shooter and gunsmith Jim See of Elite Accuracy LLC recently tested a Frankford Arsenal rotary brass tumbler. Like the older Thumbler’s Tumblers, this can tumble your cases in a liquid solution. The wet-tumbling process worked very well Jim reports. Posting on Facebook, Jim noted: “I was super impressed with the Frankford Arsenal rotary tumbler and cleaning packs they sent me. I ran 350 pieces of brass for one hour. They now look great.” Jim appreciated not having to deal with dry tumbling media, such as crushed walnut shells. Dry media produces dust and can leave residues or clog flash-holes.
Interestingly, Jim recommends you try wet-tumbling WITHOUT using stainless media. At least give it a try. Tumbling without media simplifies the process and you don’t have to worry about pins stuck in flash-holes or case-necks*. Jim reports: “Stainless steel pins come with the Frankford kit, but mine hit the trash right out of the box. There is no need to clean the inside of your cases 100% and that’s all the pins add to the equation. The brass bumping brass with hot water and Frankford’s liquid cleaner works great all by itself.” One wag stated: “That’s great to hear. Stainless steel pins are a PITA.”
Other Facebook posters concurred with Jim’s evaluation of the Frankford Arsenal Rotary Tumbler:
“I’ve had one for a couple years, and it works well. I usually run about 250-300 Dasher cases at once in it. But I use the pins because I’m OCD about clean brass.” — David W.
“I’ve had one for a year and a half and it definitely works with or without pins.” — Luke C.
“I got one about six months ago and have yet to use any SS media. I just use some dawn, distilled water, and Lemi Shine®. Turns nasty 5.56 range brass bright and shiny.” — Brian D.
“I don’t use the pins either and use a combination of Dawn soap and Lemi Shine.” — Jon N.G.
This video shows how to assemble and operate the Frankford rotary tumbler. But note, Jim See does NOT feel that it is necessary to use stainless media.
How to Dry Your Brass — Hair Dryer Vs. Machine
The downside of wet tumbling is that you end up with a pile of wet brass at the end of the cleaning cycle. There are many ways to dry brass, from drying in the sun to using a kitchen oven (be careful not to “overcook” your brass). One Facebook poster asked Jim: “What is your drying method for wet brass, and how long does it take?”
Jim See replied: “To start I just drain off the dirty water, and rinse the brass with clean hot water. Then I roll the brass on a towel for 30 seconds and put the brass in a one-gallon bucket. Next I insert a hair dryer in the bucket (with the brass) and let it run for about 5 minutes. With this procedure, the drying process for me is done in less than 10 minutes.”
Jack Lanhart has another method: “I use a food dehydrator. It takes 30 to 45 minutes.”
For those who don’t want to mess with towels and hair dryers, Frankford Arsenal offers a matching Platinum Series Case Dryer that simplifies the process of drying brass. Lyman also makes an excellent Cyclone Case Dryer. Both drying machines cost about $60.00 and both have multiple levels so you can separate different types of cartridge brass. Lyman states that “The forced heated air circulation of the Cyclone will dry your brass inside and out within an hour or two, with no unsightly water spots.” The Lyman dryer can also be used for ultrasonically-cleaned gun parts.
*The Frankford Rotary tumbler does include media separators if you choose to use the provided pins or other media. CLICK HERE for diagram showing how to use media separators.
New Nightforce NX8 Scopes Serve Both Tactical and Hunting Roles
With its new NX8 offerings, Nightforce offers full-featured tactical scopes that are light and compact enough for hunting. Nightforce’s NEW NX8 Scopes bridge the gap between hunting and tactical optics — allowing shooters to get greater performance out of a smaller, lighter package. Nightforce says it has accomplished that without compromising durability, functionality, or optical clarity that has made their scopes so popular.
The two new additions to the NX8 line are the 2.5-20×50 F1 and the 4-32×50 F1 with both magnification options offered in the MOAR and MIL-C Reticles. Nightforce has managed to build a package that combines an impressive zoom range with a compact scope body while still providing tons of travel, close parallax adjustment, and refined First Focal Plane (F1) reticles.
Jason at EuroOptic explains: “These scopes represent a movement that has been brewing towards hybrid use scopes (hunting and target/tactical) and are some of the best executions of that trend thus far. We expect that these additions to the NX8 series will be immensely popular and will spur further development in this category.”
STATUS: EuroOptic expects the new NX8 models to arrive in July. EuroOptic is currently taking pre-orders for all four new NX8 scopes — CLICK links below.
The new Nightforce NX8 series combines durability and high optical performance with an 8X zoom range. Compact and light-weight, NX8 scopes offer both MOA and Mil-Radian reticles.
Product Tip from EdLongRange. We welcome reader submissions.
Research indicates the Second Class target was a 48″ x 48″ square with 24″ inner circle and 36″ outer circle. The sight mark was a central 12″ x 12″ shape representing a soldier. ALL hits scored points (3 for center circle, 2 for outer circle, 1 for outer square). NOTE: Though some sources say the Mad Minute drill used a 12″-diameter round target, this appears to be a mistake from Ian Hogg’s book “The Encyclopedia of Weaponry”. No other source mentions a 12″ circle, which would be a mere 3.82 MOA. In reality the true drill target was a 48″ x 48″ square, roughly 15 times larger. (From No.WikiPedia.)
The FCSA, started in 1985, is an international organization with members in 22 countries. Headquartered in Monroe, Utah, the FCSA has a membership of approximately 4000. While the FCSA provides a service to military and law enforcement with research and instruction as well as an active liaison in both communities, the primary charter of the FCSA is the promotion of the sporting use of the 50 BMG cartridge and its wildcat derivatives. It has been the FCSA and its members who have lead the way in refining .50-caliber cartridges, rifles, and 1000-yard plus shooting know-how. Members enjoy a quarterly magazine, a suppliers directory, an 
If you haven’t tried Lapua bullets yet you should. The Scenar-L bullets we have tested have proven extremely consistent in weight and base-to-ogive measurement.
Norma 203B vs. Alliant Reloder 15
