Leveling your scope can be a time-consuming and tedious process. The Fix It Sticks folks have changed that with the introduction of the Scope Jack. This simple unit levels a scope through contact with the flat on the bottom of the scope (opposite the elevation knob). You can do this quickly, with one hand, leaving the other free to tighten your rings once the scope is aligned. This really is a clever, effective, easy-to-use tool, as you can see in this video:
You attach the Scope Jack to the Picatinny rail on your rifle, then lossen the rings so the scope can rotate. Then simply elevate the Scope Jack with a quick twist, using a 1/4″ driver. The Scope Jack’s horizontal roller will contact the scope’s bottom flat, rotating the scope it into proper alignment, square to the rail.
Operating Instructions from Manufacturer Fix It Sticks
The Scope Jack works with any 1/4 inch driver to quickly and easily level your scope to your rail. Just mount the scope jack to the pic rail under your scope and turn the drive handle until the lifting arm engages with the flat section under your turrets. Once the scope is level, maintain pressure while tightening your ring screws to keep optic level throughout the process.
Requirements:
1. Scope much have a central flat section under turrets
2. Needs a minimum of 1/4″ clearance between rail and scope
3. Picatinny Rail must be accessible under optic
TECH TIP: You Still Must Check the Reticle Orientation INSIDE Your Scope
The Scope Jack works fast, but it is NOT the “final solution”. Why? Some scopes have a reticle that is not perfectly aligned with the turrets and/or bottom flat. We have seen scopes with vertical reticle line off as much as three degrees (3 °) from true plumb. With such a scope, you CAN set the reticle square, but then your turrets will be canted relative to the receiver. That creates issues when shooting at long range. Accordingly, if your scope has a badly canted reticle, you should send it back to the manufacture for warranty repair. Three degrees may not sound like much, but it is actually quite noticeable:
For all scopes, AFTER using the Scope Jack, we recommend you test your reticle with a plumb line. You can hang this line from a door or ceiling fixture with a weight on the bottom. Important — when using a plumb line make sure your rifle is 100% level or your results may be off. We recommend using a bubble level to help align your rifle properly.
Here’s a feel-good story about two young people excelling in the shooting sports. We can use this kind of positive message in these times, when shooting ranges have been closed and major matches have been cancelled. It’s good to see two very talented young ladies making their mark in the shooting sports.
Colt’s Manufacturing Company (Colt) has signed two talented young ladies to the Colt professional shooting team – Jalise Williams and Justine Williams. This talented twosome will now represent Colt at shooting competitions and industry events. Jalise and Justine bring exceptional young talent to the sport. Justine is a USPSA Production Grand Master and Jalise is a Single Stack Master — that means these young ladies, even as high schoolers, rank among the top USPSA shooters. Both ladies continue into 2020 with full competition schedules, including Safariland Single Stack Classic Nationals, IPSC Nationals, and IPSC World Shoot XIX in Pattaya, Thailand.
Before Joining Team Colt, the Williams Sisters Shot for Team Springfield
Jalise Williams, 17, competes in USPSA, IPSC, 3-Gun, and Steel Challenge. At the young age of 15, Jalise became the youngest Single Stack Lady National Champion in USPSA history at the age of 15. She now holds more than 100 titles. Her 2019 titles include:
Limited Lady National Champion
Single Stack Lady National Champion
L-10 Lady National Champion
L-10 A-Class National Champion
IPSC Classic Lady National Champion
“My whole world revolves around my love for the shooting sports”, said Jalise. “Colt is a legendary company and I never imagined that I would have the opportunity to represent the brand. I am beyond excited…”
Justine Williams, 15, has competed in a variety of shooting disciplines for six years. At age 13 she became the youngest-ever Production Grandmaster and at age 15 earned the PCC Grandmaster title. The first and only female to become a two-time USPSA Grandmaster, Jusine won FIVE national titles in 2019:
USPSA High Lady in the Open, Carry Optics, and Productions Divisions
USPSA High Junior National Production Champion
IPSC High Lady Production Division
Interview with the Williams Sisters
Want to learn more about the Jalise and Justine Williams? Follow the girls on their Facebook Page. There’s also a great interview with the two young talents on GunGoddess.com.
Q: When was the first time you shot a gun, who taught you and why?
Jalise was 4 and Justine was 3 when we shot our very first gun. The gun was a .357 Marlin because our parents didn’t own any .22s. My dad is a big hunter and wanted us to learn how to hunt and shoot. Our dad taught us how to shoot shotguns and rifles.
Q: What drew you to competition and what do you like best about it?
We have always been thrill seekers. We look for the biggest adrenaline hype we can find. We love to find the biggest roller coasters or scary ride we can find. We participated in swimming, gymnastics, dance, and got our black belts in Karate. But when we started shooting, it was unlike anything we had done before.
We love the rush the timer gives you. The way you move through a stage like a dance or a form in karate. The way you have to be precise like hunting. It is so different and so interesting that we can’t stop! The people are also great — they are the nicest people you will meet.
And the girls keep on winning — Jalise Williams recently took home the High Lady and High Junior titles at the Western States Single Stack Championship. Justine Williams recently shot the Mesquite Mayhem Steel Challenge Match, taking home the 1st Overall Match title and 1st Overall PCC title.
Report by Jay Christopherson
2020 Berger SW Nationals F-Open Champion Team Member, Team Lapua-Brux-Borden
I’ve been shooting F-Class for about 9 years now. In fact, I shot my very first match, a 600-yard mid-range match, using a 6mm Dasher, on March 19, 2011. My first relay was a 188-4X and my overall score was 582-19X. I remember shooting a really nice group in the 9-ring, because I dialed the scope the wrong way and I shot lots of “verification” shots before making adjustments. I also remember wondering if that was a good score for that range in those mostly calm conditions (it wasn’t). I’ve tracked every match I’ve ever shot and I’ve come a long way since then. I’ve always been a competitive person and F-Class gave me an outlet to indulge both my competitiveness and my fondness for details. In what other individual sport does a thousandth of an inch (or less!) become important? Or a tenth of a grain?
Some of my greatest pleasures in this sport come not necessarily from winning a match (though I won’t turn that down), but in identifying something small in what I am doing that has a material effect on paper. Maybe it’s a tiny change in seating depth. Maybe it’s a slightly modified strategy for making wind calls. Maybe it’s a tiny position or hold change. Whatever it is, when it works, there’s no better feeling.
I have a full-time job to go with this hobby, so finding the time for productive training is difficult. You have to really plan ahead to maximize the time you spend reloading, developing loads, and training at the range. To that end, I invest a lot of time in reducing the things that I do at the loading bench. I load ammo on a progressive press, though modified to produce ammo to my standards. I don’t clean brass. I don’t do a lot of things that most shooters would call traditional in the loading room. Because frankly, I don’t have the time between family, work, and other interests.
If it doesn’t make a difference on paper, I mostly don’t do it. Still, there are one or two loading habits I’m trying to get rid of. I also pre-seat all my ammo for matches — whatever I show up at the match with, is what I have. I don’t clean my rifle between days at the match. I had well over 200 rounds without cleaning by the time the last shot was fired at the 2020 SWN. It took a lot of time for me to get comfortable with that. That works for what I do, but I wouldn’t dare try it with any other loads or rifles, at least, not without a lot of testing to be comfortable. My original 6MM Dasher shooting Reloder 15 couldn’t go that many rounds without cleaning and building up a carbon ring. Unfortunately, I learned a tough lesson on that one my first year.
I do all my own gunsmithing, including chambering, bedding, and stock work. I’m no Keith Weil, Alex Wheeler, or some of those other guys, but I feel pretty good about the work I do. I know that when there’s a mistake or imperfection, it’s MY mistake and I can live with that. I like to keep things as minimal as possible, so I shoot off a SEB Mini (no mods) and SEB rear bag.
I also shoot with a spotting scope at Long Range, using a Kowa TSN-663 with 25X LER eyepiece and a relatively new spotting scope stand by Rod Brakhage who is a fine F-Class shooter himself. I really like how smooth and adjustable it is on the ground compared to some other rigs I’ve used.
The 284 Wheeler — Slightly Modified .284 Win
This year at the SWN, I shot a 284 Wheeler, which is a straight .284 Win that has some small modifications designed by Alex Wheeler. I think that the work and experimentation that Alex does with reamer design really shows up on paper. In 2019 I was testing the reamer in a couple barrels, looking for the right load. I shot some great relays and team practices with it that year, but this was the first time I brought enough ammo to shoot the entire week with it. Coupled with Berger’s 7MM 180 grain Hybrid Target bullets which I point to increase BC consistency, and Lapua brass, it’s an effective combination. In particular, the brass has lasted me for 13 firings with no signs of fatigue, so I expect I’ll be able to use it at Worlds in 2021 and beyond.
I also shot the entire 2020 SWN with a Vortex Golden Eagle 15-60x52mm scope, my preferred scope for individual matches. It’s a rock-solid reliable scope in my experience, with a great eye box, reliable and repeatable mechanical controls. The Vortex ECR-1 reticle has quickly become my favorite reticle. All four of my Open rifles are built on Borden BRMXD actions, Brux barrels, and sitting in X-Ring F-Open stocks, which are Robertson clones (more on that below). I’ve tried to make each of my rifles as much of an identical clone as possible.
I am not sponsored by anyone as an individual shooter, only through team sponsorship with Lapua-Brux-Borden. Which means that for individual matches, I am free to use what I think gives me the best opportunity to win for individual matches. In practice, the only difference tends to be the scope that I use, as mentioned above.
Jay Christopherson F-Open Rifle Specifications:
Cartridge: 284 Wheeler (variant of .284 Winchester)
Optics: Vortex Golden Eagle 15-60x52mm
Stock: X-Ring F-Open Stock with R.A.D.
Barrel: Brux 1:9″-twist, 32″-long barrel
Action: Borden BRMXD action
Trigger: Flavio Fare
Q: What was your biggest challenge at the 2020 Berger SWN?
Jay: The biggest challenge for me at this year’s SWN was purely mental. At past SWN matches where I had done well, I was trying to focus on not thinking about the different things going on around me. Where I was ranked on the score sheet. How well other shooters were doing. How many points or Xs I was ahead (or behind). Being worried about conditions or whether my ammo would hold up. And so on. And sooner or later, I think those things break your focus.
Going into a relay calculating the points or Xs that you can’t afford to drop is a recipe for losing. It’s like trying NOT to picture a pink elephant with purple dots when somebody challenges you try to not think of a pink elephant with purple dots. In previous SWN events, I came up just short three times in a row, for one reason or another. So, in 2020 I went in with a mental game plan.
Mental Game Plan — Envisioning Success
I pictured what it would take to be successful and what winning would feel like. First relays, then days, and then the match. I started that process months before the match actually happened. I thought about who I was shooting against and how much pressure there was to make every shot count. I thought about how I had performed or reacted in similar situations in the past. And I planned out what I would do and how I would handle those things. I strived to be neither negative nor positive — I wanted to be neutral. I wanted to be ready to win, instead of being surprised by it.
Q: What gear/hardware items give you an edge over the competition?
Jay: There’s no single piece of gear that I can think of that gives someone an edge over somebody else. It all sort of works — it’s more about being consistent with whatever hardware you have. But one piece of new gear that I tried out at the SWN was a single-piece scope mount called the Alphamount (photo below), by Richard Near of NEAR Manufacturing.
I think scope mounts are the most overlooked piece of equipment in F-Class right now — whether they be improperly aligned, improperly torqued, or just plain junk. I think people put a lot of blame on their scopes that can be traced back to mounts. The Alphamount (and single-piece mounts in general) are something that I believe in now, having done a lot of testing. It worked out OK for me at the SWN.
Action for Back-Up Rifle Is Glued and Screwed into Stock
One of the new things I am trying this year is a “glue and screw” action set-up. At the 2019 US F-Class Nationals in Raton, we got rained on a little and when I pulled my rifle apart, I found water between the bedding and action (the bedding is about 2 years old). At the SWN, I found that something had moved enough that I could torque the front action screw and bind the bolt. Not good, but luckily this was my backup rifle that I shot for Mid-Range (badly) and not my lead rifle. There could have been stock movement or other factors as well, but there was no question the bedding had shrunk when I stuck a dial indicator on it and found that my pillars were now standing proud.
Some people had been goading me to try a “glue-and-screw” procedure. Since I had nothing better to do during the COVID-19 lockdown, I pulled out the Dremel, scuffed up the action and bedding, removed the recoil lug, and glued the action into the stock. I’ve had it out a couple times since and it seems to be shooting well, but we’ll see how it holds up and what sort of difference it might make as time goes on.
Q: What is your advice to newcomers in F-Class and Long Range competition?
Jay: Find a nemesis. Someone local who puts in the same effort that you do and is as competitive as you are. Be friends, share info, but work your behind off to make sure you win on match day. I guarantee you someone reading this knows what I’m talking about. The best thing you can do is have someone who pushes you to perform better each time out. You love to win against them, but not as much as you hate to lose to them.
Q: What do you like most about Long Range and F-Class competition?
Jay: I like the challenge of F-Class — it’s a nice blend of working to get the most out of your equipment and the most out of yourself as a shooter. You can have the greatest shooting rifle in the world and it won’t matter a bit if you can’t be consistent pulling the trigger or making good wind calls. By the same token, you can be the greatest wind caller and most consistent trigger puller in the world — but it won’t matter a bit if you can’t wring the best possible performance out of your rifle for that tiny little target at 1000 yards. I like Long Range because everything is magnified — there are rarely easy shots.
Q: What do you prefer, individual events or team matches?
Jay: Team matches. No contest. Most of the reason I travel to matches is for the team events. But just throwing together a team of great individual shooters is not enough to consistently win. You have to operate as a team, which at times means subsuming your own individual goals for the good of the team. I’ve gone into big matches knowing that my team rifle is my best rifle by a mile — but knowing that the best thing for the team’s current and future success is for me to not burn that barrel out (or burning up known good components) in the individual events. And that’s fine with me. Being part of a team of shooters with the same goal, with the same drive, the same focus on team rather than individual — and able to deliver the goods — that’s the reason why I do this.
Q: What kind of stock do you use and how does it behave?
Jay: I use an X-Ring Open stock, which is basically a Robertson clone. I’ve been using X-Ring for about 4 years now. I’ve been through a lot of different stocks to find the one that fits me and the way I like to shoot, and X-Ring has done that for me. There’s a lot of focus recently on lowering the center of gravity and extending the stock length through various methods to solve problems like torque, jump, etc. — those are just problems that I don’t experience or, at least, that don’t bother me while I’m shooting. So, I don’t tend to worry about them. The X-Ring fits nicely and runs very well in the bags that I use. I do think that you have to spend some time finding the right bag setup for the stock you are using. I have at least 9 different rear bags that I have tested at one time or another until I settled on my current bag.
Q: Do you have any specific Gun Handling Tips for F-Open shooters?
Jay: As for gun handling, I prefer a light hold — my cheek indexes off the stock with a very light touch and my trigger hand indexes off the stock also with a light touch so that I have a consistent trigger finger position. What I do is in the style of “free recoil”, but is NOT fully “free recoil”, since I DO lightly touch the stock. For the butt, I run the R.A.D. recoil reducer at its lowest setting, which means that I can barely touch off for indexing purposes and still not interrupt the recoil pulse because the R.A.D. absorbs it. This was a suggestion that Will McCloskey made to me a couple years ago in place of leaving space.
This video, from a past Berger SWN, illustrates Jay Christopherson’s shooting style. He employs a very light touch on the gun. The front rest is a SEB Mini. If this Facebook video doesn’t load,CLICK HERE.
My hold for F-Class has evolved over time into what it is now. There are lots of successful shooters that are using varying degrees of holds, from light to hard. Again, It all sort of works — the most important part is that whatever you do is consistent and repeatable, hence my touch points that ensure my head, shoulder, and trigger finger are in the same position every time. There are shooters out there that will rant about “the fundamentals of shooting” and insist that your legs have to be a certain way, your cheek has to be a certain way, your breathing has to be done a certain way. I’m sure that’s valid for what they do and I’m fine with them looking down on me for it, but I do what produces results for me. For certain, my position and hold when shooting sling is completely different. All it means is that you have to be prepared to adapt.
PARTING SHOT — Have Guns, Will Travel
Here is one of Jay’s other F-Open Rifles. When traveling he separates the stock from the barreled action. He uses a custom-cut foam piece that holds the components very securely. Note the separate slots for barreled action, stock, scope (in rings), bolt assembly, and spotting scope.
In an unprecedented move, the central government of Canada, without parliamentary vote or debate, has banned a vast number of rifles, including most modern mag-fed, semi-auto rifles currently for sale. This action banning the firearms was done by Prime Minister Justin Trudeau via “Order-in-Council”, with no political debate and no vote of elected representatives. It was essentially an Executive action, rule by fiat, like a decree issued by a dictator.
Starting now, around 1,500 models of long-arms have become illegal to sell, transport, import or use in the Canada, according to CBC News.
“The government implemented the ban immediately, and without the need for legislation in Parliament, by reclassifying about 1,500 firearm models as prohibited. In the meantime, a two-year amnesty is now in effect for Canadians who own the banned firearms and government officials said gun owners will also have the option to be ‘grandfathered’ in with weapons they currently own, although no details were available for that program yet”. Source: NationalPost.com
Nova Scotia Killer Posed as Police Officer
This action came in response to the Nova Scotia killings by a madman, Gabriel Wortman, who dressed in a police uniform and used vehicles with law enforcement markings and lightbars. Wortman was NOT licensed to possess his weapons and had obtained his firearms illegally. According to Global News: “During the shooting, the gunman was traveling in a replica police vehicle and wearing an authentic police uniform.”
Canadian Investigators said Gabriel Wortman had several semi-automatic handguns and at least two semi-auto rifles, which may have been AR-type rifles, but we are not certain about the exact configurations of Wortman’s long guns. Notably, most if not all of Wortman’s guns were already ILLEGAL for Wortman to own under existing Canadian laws. The crazed shooter had violated multiple firearms laws already on the books, and did NOT possess his weapons legally (it is believed he sourced them from outside Canada). AR-type rifles required a special permit in Canada. And of course he violated multiple laws in impersonating a law enforcement officer.
Trudeau Exploits Nova Scotia Shooting to Ban Guns without Normal Legislation
Prime Minister Trudeau used the Nova Scotia mass killing as the impetus to fulfill his campaign promises to ban so-called “assault-type” weapons. Seven months ago, Trudeau pledged to ban modern semi-auto rifles, which he called “assault rifles”. Trudeau opportunistically leveraged the mass shooting to execute his plan with no public debate and no vote by elected officials.
Trudeau’s actions were criticized by many in Canada. Conservative Leader Andrew Scheer declared: “Taking firearms away from law-abiding citizens does nothing to stop dangerous criminals who obtain their guns illegally”. Alberta Premier Jason Kenney stated: “Today’s order does little to target criminals … instead, Ottawa is singling out law-abiding gun Canadians who purchased their property legally”. And Alison de Groot, Director of the Canadian Sporting Arms and Ammunition Association, said Trudeau’s gun ban “will strand somewhere between $200 to $300 million worth of pre-paid merchandise in stores”. READ MORE.
Q: Would a Ban on Semi-Auto Rifles Have Prevented the Nova Scotia Tragedy?
A: No. The killer Gabriel Wortman also used pistols, and could have been just as deadly with a pump shotgun. And nine of the 22 killed “died in house fires” set by Wortman. (Source: RCMP per Reuters.) Remember that fact — 40% of the victims were burned to death: “Of the 22 people killed, 13 were shot and nine died in house fires.” Source: CNN.com.
The real reason for the high kill count was that Gabriel Wortman was an insane maniac wearing a police uniform and driving a police car. The important questions to ask are how did he get the uniform and why were vehicles sold complete with police markings?
Terms of Canada’s Broad New Gun Ban
Under the Canadian gun ban, owners of prohibited firearms now have two years to turn in their rifles. According to CTV News: “Owners will also have the ability to be compensated through a buyback program, though the details of these options have yet to be outlined. Gun owners must be in compliance with the law by April 2022. Those who have not disposed of any banned firearms by that time may face sanctions under the Criminal Code.”
Was Trudeau’s massive gun ban necessary? Consider this comment from a Canadian gun owner: “Handguns and AR15s in Canada [were] highly regulated already. To get the license you go through a 2-day course. There was a 3- to 6-month wait for your application. Spouse must sign. No history of metal disorders. [Authorities conduct] phone interviews with credible people who know you. When you get your licence you must join a shooting club[.] Now you have your restricted license … and a government issued travel licence.”
Here is a list of all the firearms that have been banned (without Parliamentary vote) by Trudeau’s government. This includes AR15-platform rifle, AR10 rifles, Ruger Mini-14s, Semi-Auto M14-type rifles, and many other varients. Some big bolt-action guns will banned as well. ELR Researcher notes: “Read down to section 96: ‘Any firearm capable of discharging a projectile with a muzzle energy greater than 10,000 joules[.]’. Well 10,000 joules is 7375 foot-pounds, meaning [this would ban] ALL firearms chambered for most commercially-available .408 CheyTac, .416 Barrett, and .50 BMG ammo.”
Use the scoll bar (on right) to move through the list of prohibited firearms.
The February 2013 edition of Shooting Sports USA magazine has an interesting feature by Glen Zediker. In this Transporting Success, Part I article, Zediker explains the advantages of loading at the range when your are developing new loads or tuning existing loads. Glen, the author of the popular Handloading for Competition book, discusses the gear you’ll need to bring and he explains his load development procedure. In discussing reloading at the range, Glen focuses on throwing powder and seating bullets, because he normally brings enough sized-and-primed brass to the range with him, so he doesn’t need to de-prime, re-size, and then re-prime his cases.
Zediker writes: “Testing at the range provides the opportunity to be thorough and flexible. You also have the opportunity to do more testing under more similar conditions and, therefore, get results that are more telling. Once you are there, you can stay there until you get the results you want. No more waiting until next time.”
Zediker starts with three-shot groups: “I usually load and fire three samples [with] a new combination. I’ll then increase propellant charge… based on the results of those three rounds, and try three more. I know that three rounds is hardly a test, but if it looks bad on that few, it’s not going to get any better.”
Glen reminds readers to record their data: “Probably the most important piece of equipment is your notebook! No kidding. Write it down. Write it all down.”
There’s More to the Story…
Editor’s Note: In Zediker’s discussion of loading at the range, he only talks about throwing powder and seating bullets. In fact, Glen opines that: “there is little or no need for sizing.” Well, maybe. Presumably, for each subsequent load series, Zediker uses fresh brass that he has previously sized and primed. Thus he doesn’t need to de-prime or resize anything.
That’s one way to develop loads, but it may be more efficient to de-prime, re-size, and load the same cases. That way you don’t need to bring 50, 80, or even 100 primed-and-sized cases to the range. If you plan to reload your fired cases, you’ll need a system for de-priming (and re-priming) the brass, and either neck-sizing or full-length sizing (as you prefer). An arbor press can handle neck-sizing. But if you plan to do full-length sizing, you’ll need to bring a press that can handle case-sizing chores. Such a press need not be large or heavy. Many benchresters use the small but sturdy RCBS Partner Press, on sale now at Amazon for $77.99. You may even get by with the more basic Lee Precision Compact Reloading Press, shown in Zediker’s article. This little Lee press, Lee product #90045, retails for under $35.00.
With so many Americans stuck at home under governmental lockdown orders, we’re offering a visual escape from the stay-at-home pandemic doldrums. Here are some great rifle-centric outdoor photos courtesy of Nightforce Optics. Perhaps these “gunscapes” will encourage you to grab your rifle and head out into the wilderness when Americans’ freedom of mobility/travel is finally restored. The good news is the same states are opening ranges again.
These fine photographs remind us of the lure of the great outdoors for a rifleman. We hope that soon our readers will once again be able to experience the grandeur of America’s mountains and wild backcountry. These images are part of an ongoing series of rifle photos posted on the Nightforce Facebook page. Can you identify the optics, and any of the locations?
This story first ran ten years ago. But to mark our long-standing friendships with shooter Joe Friedrich and chassis builder Gary Eliseo, we wanted to reprise the article for a new decade. Joe’s Eliseo-chassis 6BR rifle delivered some of the most stunning factory ammo accuracy we’ve ever seen, in any rifle, in any caliber.
Amazing Accuracy from 6mmBR Tubegun
What kind of accuracy do you think a tubegun can deliver with factory ammo — during barrel break-in? Perhaps 0.6″ at 100 yards, half-MOA if the conditions are perfect? Well you may want to change your preconceptions about tubeguns — and factory ammo. This Eliseo R5 repeater, smithed by John Pierce with a Pierce CM action and Broughton 5C barrel, shot the Lapua 90gr factory ammo into flat ONEs during the break-in session. A day later, in tricky 8-14 mph winds, the gun nailed a witnessed and software-measured 0.174″ 5-shot group using the 105gr factory ammo. That would be impressive for a “full-race” benchgun with precision handloads. For an across-the-course rifle shooting factory ammo, it’s pretty amazing.
Eliseo Tubegun Shoots in the Ones
This accurate rifle belongs to our friend (and designated expert trigger-puller) Joe Friedrich. During the initial break-in session, since his reloading dies had not yet arrived, Joe decided to start with some Lapua factory-loaded 6BR ammo he had on hand. After doing a few two-shot-and-clean cycles (with patches and nylon brush), Joe decided to try a 3-round group just to see if the Broughton barrel had some potential. To his astonishment, the Eliseo R5 put three rounds in 0.100″ (photo below left). Joe then cleaned the barrel again, shot a couple foulers and tried a 4-shot group. The results were just as stunning — 4 shots in a mere 0.104″ but three in virtually one hole (photo below right).
You Can’t Believe How This Gun Shoots
Joe called your Editor and said “You can’t believe how this gun shoots with factory ammo!”. So we arranged a photo session for the next afternoon, where I could verify the rifle’s accuracy. Well it turned out the conditions were way more challenging than when Joe broke in the barrel the day before. Winds were running 8-14 mph and were swinging through 180 degrees half-way down the range. Joe fired a few 90s through the Oehler chronograph at my request, then opened a box of Lapua 105gr factory ammo. It took about four rounds for the barrel to settle in after being cleaned the night before. Then Joe got serious, and with your Editor looking over his shoulder, he drilled a 0.174″ five-shot group in switching winds, doping every shot. Joe felt the gun could have shot tighter but he missed one wind call.
Serious Accuracy with a Multi-Purpose Rifle
So there you have it — a tubegun that shoots in the ones with factory ammo. Joe says that, at least with the 90s, the Elesio R5 shoots as well as his 6 PPC. Joe stressed that “steering the tubegun is hard work. You really have to concentrate compared to a purpose-built bench gun like my PPC. With the tubegun, everything has to be perfect on every shot — hand position, cheek position, stock position in the bag. If you’re off just a little bit, it’s easy to steer the gun the wrong way and send a shot out of the group.”
Accuracy Great But Fouling Heavy and ES Could Be Better
Have there been any negatives to Joe’s 6BR tubegun experiment so far? Well, the Broughton 5C barrel, while phenomenally accurate, shows signs of being a bad fouler. Copper built up pretty quickly over the first 25 rounds or so. We saw best accuracy with a recently-cleaned barrel. Hopefully the fouling will lessen as the barrel polishes in with use. And the canted land barrel is slower than average with the factory ammo. Lapua rates its 90gr naked-bullet ammo at 2950 fps with a 26″ tube. In Joe’s 27.5″ barrel we only averaged 2901 fps. With the 105gr factory ammo, which is rated at 2790 fps, we averaged just 2694 fps. That’s quite disappointing. Also the ES on the factory ammo, slightly over 50 fps for both bullet types, wasn’t particularly good. Still, the overall results were stunning. This gun shoots better than many long-range benchrest rifles running carefully-developed handloads — and it does that with factory ammo, right out of the box.
Joe Friedrich is a superb benchrest shooter, who has won many matches and set National Records in ARA rimfire benchrest competition. Here is Joe with “Sweet Pea”, his favorite .22 LR rimfire rig. With over 100,000 rounds through the Benchmark barrel, this well-worn rifle set an ARA 4-target Aggregate record! READ about Sweat Pea Record HERE.
Breaking News April 25, 2020: There is a report that CA’s Attorney General has applied to the Federal 9th Circuit Court of Appeals for an Emergency STAY of the injunction issued by Judge Benitez blocking application of California’s ammunition background check system. We are working now to determine the status of the case.
Currently in California, citizens must go through a state background check to purchase ammunition — any ammunition. And for quite some time, California residents have not been able to purchase ammunition from out of state, unless the ammunition is first shipped to an approved California ammo dealer. All ammo sales must take place in-person through licensed ammunition vendors. This has all resulted in significantly increased ammo costs in California, and failure of the state’s computerized ammo check system has resulted in over 16% of legitimate purchasers being denied the right to obtain ammunition.
Now all that may change. In Rhode v. Becerra, Federal District Court Judge Roger Benitez has determined that the California ammo check system is fatally flawed and unconstitutional. On April 23, 2020, the Judge granted a temporary injunction which halts California’s ammo background check system and lifts California’s blockade of ammo imports from other states. Californians may now again purchase ammo directly from out-of-state vendors. READ Injunction Decision HERE.
Judge Benitez called California’s ammunition background check law “onerous and convoluted” and “constitutionally defective”. The Judge stated that: “The background check experiment defies common sense while unduly and severely burdening the Second Amendment rights of every responsible, gun-owning citizen desiring to lawfully buy ammunition”. Notably, the lead plaintiff in the case, Kim Rhode, is an Olympic Gold Medalist trap shooter, whose ability to obtain competition-grade shotshells was impaired by California’s “onerous” ammo purchase restrictions.
California’s ammo laws blocked sales to legitimate, law-abiding buyers about 16% of the time, the Judge noted. Moreover, in his 120-page Opinion, the Judge held that the state’s ban on importing ammunition from outside California violates federal interstate commerce laws.
As reported by the NRA-ILA: “The [court’s] Thursday’s injunction means the law cannot be enforced while the case is active unless the decision is stayed.”
Judge Benitez slammed California’s Ammo Check law: “The experiment has been tried. The casualties have been counted. California’s new ammunition background check law misfires and the Second Amendment rights of California citizens have been gravely injured.
These new laws are constitutionally defective for several reasons. First, criminals, tyrants, and terrorists don’t do background checks. The background check experiment defies common sense while unduly and severely burdening the Second Amendment rights of every responsible, gun-owning citizen desiring to lawfully buy ammunition. Second, the implementing regulations systematically prohibit or deter an untold number of law-abiding California citizen-residents from undergoing the required background checks. Third, in the seven months since implementation, the standard background check rejected citizen-residents who are NOT prohibited persons approximately 16.4% of the time. Fourth, the ammunition anti-importation laws directly violate the federal dormant Commerce Clause.”
This Video analyzes the decision in Rhode v. Becerra
Constitutional Rights Must Be Preserved Even in Times of Crisis
The Judge stressed that Constitutional rights should not be sacrificed, especially in these challenging times: “Law-abiding citizens are imbued with the unalienable right to keep and bear firearms along with the ammunition to make their firearms work….. Presently, California and many other states sit in isolation under pandemic-inspired stay-at-home orders…. Maintaining Second Amendment rights are especially important in times like these. Keeping vigilant is necessary in both bad times and good, for if we let these rights lapse in the good times, they might never be recovered in time to resist the next appearance of criminals, terrorists, or tyrants.”
How did California politicians react to their defeat in Court? Read comments from CA Attorney General Xavier Becerra and other state officials in Associated Press Report reprinted by NBC Los Angeles.
The Civilian Marksmanship Program (CMP) issued a statement yesterday, April 22, 2020, announcing the complete cancellation of the 2020 National Matches at Camp Perry — all rifle and pistol matches are cancelled. Sadly, due to the Coronavirus Pandemic, and concerns about ongoing stay-at-home and social distancing orders, the CMP declared that there will be no Camp Perry National Matches in 2020:
Official CMP Statement about 2020 National Matches
After thoughtful consideration and reflection, the Board of Directors of the Civilian Marksmanship Program announces the cancellation of the 2020 National Matches at Camp Perry.
“This decision was not arrived at lightly, but was prompted by restrictions resulting from the COVID-19 pandemic. These matches date back to 1903 and have been held at Camp Perry since 1906,” said Judith Legerski, CMP Board Chairman.
“The health and safety of our competitors, participants, vendors, military support, volunteers and staff members is of the upmost importance — overriding even the historical imperative of maintaining the continuity of the Matches,” agreed Legerski, with Chief Operating Officer Mark Johnson and Programs Chief Christie Sewell.
“We were unable to come up with a manner in which we could safely produce the Matches. Housing and pit duty were amongst the many insurmountable problems faced by the CMP Board,” Legerski explained.
The CMP looks forward to the 2021 National Matches at Camp Perry as the best marksmanship celebration ever! In the meantime, please stay safe and healthy at home, as we prepare for the new normal ahead of us.
All CMP operations have been shut down since mid-March and a full resumption of business remains undetermined. Full refunds will be made to those who have already registered.
Story based on Report by Dean Weingarten
The NICS numbers for March 2020 established new, all-time records for both the number of projected guns sales as well as the numbers of NICS background checks done in one month. In March 2020, 3,740,688 NICS checks were done, according to official FBI statistics.
The previous one-month NICS record was set in December of 2015, when 3,314,594 NICS background checks were done. In March of 2020, the FBI recorded 3,740,688 NICS background checks, 12% higher than the previous record. The number of NICS checks always exceeds that actual number of gun sales, because some checks are done for other purposes. The estimated number of recorded long gun, handgun, and other gun sales totaled 2,373,193 in March 2020, 7% higher than the previous sales record in December of 2015.
Guns Sales Driven by Pandemic Fears
According to MSN News, “With most of the nation in isolation to halt the spread of coronavirus … the FBI has seen a 41% increase in background checks compared to this time last year.”
Click Image to Go to MSN to Watch Video (then Click Speaker icon for audio).
Most Background Checks Were for Handguns
In March 2020, most of the purchases were for handguns instead of long guns. The numbers for March were: Handguns, 1,392,677 NICS checks, long guns, 758,073 NICS checks, other (mostly receivers, which could be made into either handguns or long guns) 79,129, and multiple 57,328. Multiple checks are multiplied by 2.5 to approximate the number of gun sales. Carry Permit NICS Checks Rising Faster
Notably, there has been significant growth in the number of NICS checks associated with CCW Carry Permit applications. NICS checks for carry permits and carry permit rechecks have been increasing much faster than checks for firearm sales. While states maintain their own databases for Carry Permits, NICS checks are done in connection with permit applications and renewals.
Total Guns in USA Close to 450,000,000
Using the figures available, there were about 430 million private firearms in the United States at the end of 2018. About 18.6 million have been added since then, putting the USA close to 450 million at this point. According to Dean Weingarten, the United States is on track to reach 500 million privately owned firearms by the end of 2024.
I do all my own gunsmithing, including chambering, bedding, and stock work. I’m no Keith Weil, Alex Wheeler, or some of those other guys, but I feel pretty good about the work I do. I know that when there’s a mistake or imperfection, it’s MY mistake and I can live with that. I like to keep things as minimal as possible, so I shoot off a SEB Mini (no mods) and SEB rear bag.
There’s More to the Story…
Amazing Accuracy from 6mmBR Tubegun
You Can’t Believe How This Gun Shoots
Judge Benitez called California’s ammunition background check law “onerous and convoluted” and “constitutionally defective”. The Judge stated that: “The background check experiment defies common sense while unduly and severely burdening the Second Amendment rights of every responsible, gun-owning citizen desiring to lawfully buy ammunition”. Notably, the lead plaintiff in the case, Kim Rhode, is an Olympic Gold Medalist trap shooter, whose ability to obtain competition-grade shotshells was impaired by California’s “onerous” ammo purchase restrictions.
