|
|
August 12th, 2009
Virginia Gunsmith Richard Franklin sold his stock-making business to Greg West, but Richard is still making stunning, one-off custom rifles using laminated fancy woods such as Crotch Claro Walnut, Turkish Walnut, Curly Maple, Bloodwood, and burls. One of Richard’s favorite sources for fancy woods is Northwest Timber, based in Oregon. NW Timber has one of the largest collections of highly-figured Claro Walnut and fancy Maple blanks in the country, including many “book-matched” sets that are ideal for a three-layer laminated stock. The two, mirror-image, book-matched pieces form the outer layers, with a central spine of contrasting wood.
When shopping for fancy wood for a laminated stock application, be sure to consider the length and thickness required. For a tri-laminated benchrest stock with a 3″ forearm, you’ll need a block at least 2.5″ wide and 32″ to 35″ long (depending on overall stock length). After sawing that will give you two 1 1/8″-wide slabs, so that a contrasting 3/4″-wide section of wood can be placed in the middle. Thinner blocks of fancy wood can be used in a 5-layer laminate. If you can’t find a block at least 32″ long, a contrasting end cap could be placed on the fore-end. However, Richard prefers to work with blanks that are long enough for the whole stock.
Above is a book-matched set from Northwest Timber in Crotch Claro Walnut. Note how there are two matching pieces, top and bottom.
This above photo shows how spectacular Quilted Maple can look when stained and finished with contrasting highlights. A popular material for fine musical instruments, Quilted Maple can look just as good on a gunstock (below).
For more information, contact:
Northwest Timber
3229 Jefferson-Scio Drive
Jefferson, OR 97352
(541) 327-1000
August 11th, 2009
This time of year, many of our readers are traveling far and wide to shooting events, including the National Championships at Camp Perry. Security is vital on those long trips when you’re hauling lots of guns and shooting gear. A custom, high-end Benchrest, F-Class, or High Power rifle can cost upwards of $4000.00. And that’s without optics, which can run another $2000.00 per rifle. If you’re transporting three or four match rifles with premium scopes, you could be hauling $16,000 worth of firearms. Bring along a rangefinder, Co-Axial rest, spotting scope, and chronograph, and that could push the total closer to $20,000.
 How do you safeguard that kind of investment? One of the best storage systems available is the TruckVault, built in Washington state. TruckVaults are custom-fitted, locking storage cabinets that fit in a pickup truck bed, SUV, or station wagon. Various designs are available, including a waterproof “Extreme Series”. Both single-drawer and multi-draw layouts are offered with lengths up to 60″ overall, and top-load capacity of 2000 pounds. A variety of interior configurations are available.
For transporting scoped match rifles, we suggest TruckVault’s “Magnum Line”, which has two drawers with 10.5″ of vertical clearance. This offers two primary sliding compartments (on roller casters), plus smaller storage boxes where you can keep valuable gear securely out of sight.
TruckVaults carry a big price-tag. SUV models start at $1485, but expect to pay closer to $2000.00 for a unit with all the bells and whistles. That’s serious money, but you have to balance that against the cost of the firearms and accessories you are transporting. If you spend much time on the road with a pricey collection of guns, optics, and accessories, a TruckVault may be a wise investment. This editor first saw a TruckVault on a Chevy Suburban belonging to an Arizona gunsmith who does work for the military. It was not unusual for him to haul $50,000 worth of Class III weapons. For him, the TruckVault was an essential security feature. For more info, visit TruckVault.com or call (800) 967-8107.
August 8th, 2009
Sam’s Club is offering one of the best deals in gun safes right now — a 60″ H x 30″ W x 22″ L Liberty Centurian safe for $688.00. That is the store pick-up price. The safe weighs 520 lbs. and has 23 cubic feet of exterior volume. Walls are 12 gauge steel and the safe is fire-rated for 30 minutes at 1200° F. The lock is a Sargent & Greenleaf electronic, one of the best units in its price range. This very same safe is sold by Liberty Dealers for $999-$1099.00. If you’re able to get this safe home on your own, this is an excellent value from a respected safe-builder. I’ve got a friend who purchased one of these safes and I helped him install it and set up this interior. I can assure you that you’ll have trouble finding more safe for the money. I consider it better than a $1000.00 Canon I used to own.
Note, you’ll have to call your local Sam’s Club for availability and exact price. If it’s not available at the closest outlet, try other nearby Sam’s Club stores (you can search for availability on the Sam’s Club website). Typically a Sam’s Club outlet will get a half-dozen of these and they’ll sell out in a few days. Also, we want to caution people that this safe, while far more secure than a typical “security cabinet” with a locking key, is a far cry from a serious 1500-lb commercial-grade safe. On the other hand this safe is just about the biggest size that can be easily handled by a couple non-professional guys working with a furniture dolly. The unit is delivered on a wood pallet — we recommend leaving the pallet on until you get the unit inside and positioned. Then remove the wood and bolt down the safe through the four holes are pre-drilled in the bottom (these are hidden by the carpet).
Here’s a review from a buyer who purchased this Liberty Safe at Sam’s Club: “We really shopped the competition prior to purchasing this safe. For the fire rating and the storage space, this was consistently $200-$600 less than many of the other membership retailers in addition to ALL sporting good stores (even the Mega stores.) The safe is packaged well and the instructions are pretty thorough also. The mechanics are as good as any gun-store-bought safe, better in most cases. The S&G lock is easy to program and use. Just be sure the lock handle is twisted all the way counterclockwise [after you close the door]. The modular interior is great. We store some paperwork, ammunition and of course firearms in the safe and there’s more than enough room. Sam’s Club is untouchable on the price of this safe. Do the homework yourself — it’s the best value for the money anywhere.”
August 3rd, 2009
The August issue of Target Shooter, the excellent UK-based webzine, is now available FREE online. As usual, this edition is chock full of interesting feature articles written “by shooters, for shooters”. You can either read the monthly e-magazine online, OR you can now download the entire August issue to your computer. This lets you peruse multiple articles at your leisure. (For readers with a slow web connection, reading offline may be more convenient, once you’ve downloaded the file.)
 Among the featured articles this month are an authoritative section on rifle maintenance and scope-mounting by Vince Bottomley (p. 13), a user’s guide to the Redding T7 press by Laurie Holland (p. 55), and an excellent guide to Rimfire Ammo selection and sorting by Carl Boswell (p. 40). If you follow Carl’s procedures (including the visual inspections shown at right), you’ll experience fewer unexplained “flyers” — we can guarantee that.
Complete F-Class Worlds Report
Amazingly, Target Shooter’s August issue contains a detailed, 4-page report on the 2009 F-Class World Championships which concluded just a few days ago in England. You’ll enjoy the reports from the field and interviews with top F-Classers from around the world. In addition to the match report, the August Target Shooter profiles Britain’s Gary Costello, the winner of the Individual World F-Class Championship.
Gary’s rifle was built by American gunsmith Alan Warner and is chambered as a 7mm-270 WSM. (The 270 case is used because it has a slightly longer neck and slightly less capacity). The action is an aluminium Stolle Panda with RBLP configuration. The scope is a March 10-60X mounted in Kelbly rings. The stock is an Alex Sitman Master Class laminated long-range thumbhole model. Sadly, the handsome gray/blue stock broke at the thumb-hole during shipping from the USA. However, Pet Walker of Walker Customer Rifles in West Yorkshire restored the stock to better than new condition, providing Gary with a beautiful rig that carried him to victory.
July 29th, 2009
 Here at AccurateShooter.com, we have promoted the “20 Practical”, a great little cartridge created by simply necking down the .223 Remington to 20 caliber. Popularized for bolt guns by Warren B (aka “Fireball”), the 20 Practical is also an excellent choice for an AR-platform varmint rifle. It offers better ballistics than a .223 Rem, with less recoil, and more velocity. Plus the 20 Practical, by all indications, appears to be an inherently accurate cartridge that “wants to shoot”. Our own AR ‘Ultimate Varminter’ project rifle, developed with Robert Whitley, was chambered as a 20 Practical. That gun shot “lights out”, demonstrating how well the little cartridge works.
Forum member ‘Dennis in VA’ recently put together his own 20 Practical AR with all-premium components. Dennis took his impressive new gun to the range yesterday, and it looks to be a tack-driver. Check out the target below, shot with Sierra 39gr BlitzKing bullets. That’s three shots in 0.375″ edge-to-edge, at 100 yards. (NOTE: regarding this H335 load, we advise to start 10% low and work up.)
Dennis got his upper from Whitley’s AR-X Enterprises. It features a heavy billet upper receiver (with side charging handle), fitted with a 24″ PacNor SS Super Match 11-twist barrel. Mounted to the upper is a +20 MOA, GS-1 Scope Rail from GG&G. Riding on top is a Nightforce 5.5-22X50 NP-R1 scope in Nightforce ultra-light rings.
The lower is equally exotic. Machined from billet by American Precision Arms, it is fitted with with a RRA LPK and a Geissele trigger. The tan, adjustable stock is a Magpul PRS model (Gen II). An Ergogrip tactical deluxe Suregrip completes the build. Dennis in VA has put together a very nice set-up to say the least. And it definitely shoots.
To learn more about the 20 Practical cartridge for AR rifles, visit Robert Whitley’s 20 Practical Webpage. There you’ll find load data, info on dies and reloading, plus advice on hardware and barrel selection. Robert also has a video showing how to form 20 Practical brass.
July 20th, 2009
We generally don’t put too much stock in awards handed out by print magazines, nor the NRA’s Golden Bullseye awards (which often seem to be the “Golden Ad Revenue Payback Awards”), but we were pleased to see the Sako 85 rifle receive some recognition. The Sako 85 Finnlight stainless model received an “Excellent” rating from Outdoor Life magazine in its annual review of hunting rifles. The Finnlight ST was the only rifle tested to receive an overall rating of 4 Stars, or the classification of “Excellent”. READ Sako 85 Finnlight REVIEW.
Each year Outdoor Life performs tests and offers awards in various product categories. This year 13 new rifle models were tested and more than 3,500 rounds of ammunition were fired. “Our rigorous … testing protocol offers the toughest, most honest comparison of new hunting rifles on the market,” according to John B. Snow, Executive Editor. The Finnlight ST received “A” grades in both Workmanship and Performance. Outdoor Life’s tester wrote: “The proven Sako 85 action is as slick and reliable as they come, and the accuracy of our test sample (in .308 Win.) was impressive, especially in light of the rifle’s unscoped weight of 5 pounds 6 ounces. One of my 5-shot groups using Hornady 168gr A-Max ammo measured a scant .581″. The Finnlight is a rifle you can trust your hunt to, which is about the highest praise of all.”
The complete 2009 Hunting Rifle Test can be read online on the Outdoor Life Website. Guns tested are listed alphabetically below, and you can click the links to read individual reviews:
CLICK HERE to Read 2009 Outdoor Life Hunting Rifle Reviews.
July 11th, 2009
Having a quality funnel can help you get a carefully-measured powder charge in your cases, with no spillage, every time. If you’ve messed around with cheap plastic funnels you know that they can rock on the case mouth. Also, if the fit isn’t good, some kernels can end up on your bench, instead of inside the case.
Thankfully, precision, caliber-specific metal funnels are available to reloaders for about $10-11. Satern Custom Machining funnels feature an aluminum top with a caliber-specific, machined brass base/neck. Dick Saunders makes a simliar, turned-aluminum funnel sized for particular calibers. Both these metal funnels make reloading easier (and they are ideal for blackpowder loading because they do not give off static electricity). As Forum member Wes notes, with a fitted metal funnel: “the possibility of the funnel sliding to the side, and spilling powder all over the place is drastically reduced.”
Satern Aluminum/Brass Funnels
Steve Satern crafts rugged aluminum funnels with brass ends. The caliber-specific sizes offer a snug fit that keeps the funnel tight on the case neck while the powder is flowing. Forum member Danny Reever reports: “If you are tired of the generic ‘fits all’ funnels falling over and powder spraying every where, try one of the Satern funnels. Sinclair Int’l sells them and they are top notch.” SMike308 adds: “I have retired my plastic funnels after buying my first Satern funnel. I now have one for each different caliber that I load for. I especially like that the Satern has the brass weight at the bottom, which adds stability to the funnel.”
Satern funnels are sold by MidwayUSA (6mm $11.29), Satern Machining (6mm $10.49), and Sinclair International (Item 11-9XX, 6mm $11.95). Satern Machining also offers two types of universal funnels, 22-30 caliber and 30-50 caliber.
Saunders Aluminum Funnels
Some of our Forum members prefer the turned aluminum funnels made by Dick Saunders.
These are sold by Russ Haydon’s Shooters Supply for $9.95 each. Specify .17, .20, .22, 6mm, 6.5mm, .30 caliber or “all-purpose”. If you have questions, you can contact contact Saunders directly:
Dick Saunders
145 Delphi Rd.
Manchester, IA 52057
563-927-4026
July 8th, 2009
Long-range benchresters and varminters seeking extra stability should take a look at the “Big Dawg” MBR Tracker from Bill Shehane (D&B Supply). This features a longer, deeper, and wider fore-end for added stability and more resistance to torque with the heavy calibers. Called the MBR ‘Big Dawg’, this stock is cut 4″ longer than a standard Shehane ST-1000 Tracker. This provides a “longer wheelbase” for better balance with very long (30″+) barrels. (The ST-1000 itself is 3″ longer than most benchrest stocks.) The Big Dawg is available with a 4″-wide or 5″-wide forearm, and will handle barrels up to 40″ in length and 1.5″ in diameter. In the top photo, taken by Forum member Preacher, you see a 4″-wide Big Dawg next to a normal ST-1000 Tracker. (Both stocks are symmetrical; there is distortion caused by wide-angle lens.)
This color pattern is what Bill calls “Prairie Dog Camo”, a Rutland laminate in orange and dark gray, with olive ‘accent’ layers. The price for a ‘Big Dawg’ in Rutland laminate is $525.00. In African Obeche wood (any color choice), the price is $725.00. For more info, contact Bill Shehane at (704) 824-7511, or visit his website, www.ScopeUsOut.com.
July 6th, 2009
 Carl Bernosky, 8-time winner of the Camp Perry National High Power Championships, will be switching back to a bolt gun for the 2009 competition. Last year, Carl shot an AR15-based spacegun built on Smith & Wesson M&P15 components. With that rifle, Carl became the first competitor to win the Camp Perry High Power Championship shooting an AR15-type semi-auto.
But this year Carl will be shooting a 6.5 Creedmoor CSR-1 TubeGun from Creedmoor Sports. Based on a TubeGun Chassis and buttstock by Gary Eliseo (of Competition Shooting Stuff), the CSR-1 features a Pierce Precision Rem 700-clone receiver, and a 28″ Broughton barrel.
Both the buttstock and the handguard are adjustable to suit the shooter. The handguard/float tube can rotate 15 degrees from center in either direction, allowing the shooter to adjust his desired rifle cant. The 4-way buttstock adjusts for length-of-pull, cant, buttpad height and offset. There is an adjustable cheekpiece and even two 4.8-ounce removeable weights to allow precise balancing of the rig.
The CSR-1 is offered in five (5) chamberings: 308 Win, 6.5 Creedmoor, 6.5×47 Lapua, 6XC, and .223 Rem. At Camp Perry, Carl Bernosky will be shooting a 6.5 Creedmoor version of the rifle, using Hornady components.
CLICK HERE to learn more about specs and features of CSR-1 ($3750.00 complete).
June 18th, 2009
 The full line of K&M reloading tools and accessories is now offered by PrecisionReloading.com. The popular K&M Arbor press (with optional seating force measurement gauge) is in stock. The K&M arbor costs $78.00, or $115.00 with the force measurement system. This clever design uses a Belleville washer stack and linkage to show the force required to seat your bullet on a standard dial indicator mounted on the top (dial indicator is $22 extra.) In addition, Precision Reloading offers K&M neck-turning tools, primer seaters, expanders, neck reamers, and flash-hole uniformers.
This editor has tried out many different arbor presses. The K&M is my favorite. For me, the force measurement system acts like a warning light, telling me if something is way off in the bullet seating process. If you see the dial indicator needle jumping around wildly, or spiking too soon, you know that case has excessive neck tension, or perhaps the bullet is oversize in diameter (it happens). Currently, the K&M is the only arbor press with a seating-force gauge. The only down-side to the K&M arbor is that you must adjust multiple bolts to set the ram height. By contrast, the Sinclair Int’l Arbor and some other arbors feature a quick-release lever that lets you adjust ram height quickly and easily.
Based in Mitchell, South Dakota, Precision Reloading is run by active, knowledgeable shooters. In addition to centerfire reloading supplies and tools, Precision Reloading offers a full line of shotshell components and shotgun reloading equipment, plus optics, cleaning supplies, gun cases, and hunting gear. This month Precision Reloading is running an optics sale on Bushnell, Sightron, and Vortex scopes, binoculars, and spotting scopes.
|
