OK guys — check your powder stashes. Here’s an important notice regarding Accurate 2520 powder. There is one lot of Accurate 2520 that is dangerous, so you should not load with it. If you have some of this powder from Lot 0913192116, stop using it, and contact Western Powders at 406-234-0422. Western Powders issued this notice on 7/1/2020:
ACCURATE 2520 RECALL — 2520 Powder — LOT 0913192116
Western Powders is issuing a recall of Accurate 2520 1 lb. bottles with lot number 0913192116. The lot number is stamped on the back of the bottle. This is a limited recall and ONLY applies to this lot number of Accurate 2520. USE OF THIS POWDER MAY RESULT IN HIGH PRESSURE LOADS AND SUBSEQUENT GUN DAMAGE OR SERIOUS PERSONAL INJURY. If you are in possession of this propellant, please discontinue use immediately and contact Western Powders at 406-234-0422. We will replace your powder and instruct you how to dispose of this powder.
Product innovation is all about “building a better mousetrap”, or in this case, building a better bore-cleaning patch. A real smart guy, Shane Smith, has invented a triangular patch that earned a patent. The U.S. Patent Office has awarded a utility patent for BoreSmith’s Triangle Patch™. This unique cleaning patch was designed by Shane Smith, a mathematician/physicist who employed his scientific and firearms knowledge to create innovative bore-cleaning products.
BoreSmith’s clever Triangle Patch™ (aka Pyramid Patch) presents more cleaning surface area to the bore wall than does a conventional square or round patch (of equivalent size). At the same time, the unique geometry makes Triangle Patches much less likely to jam in the barrel. This is because the notches in the sides of the triangle allow the patch to sit more uniformly on the jag (without bunching up). In addition, the Pyramid patch is must less likely to jam due to pleating. One reason conventional patches get stuck is unwanted 5-layer pleating. The special notches in the Pyramid patch remove all or most 5-layer pleating. As a result the patch does not bunch up and this also reduces rod bowing. SEE Triangle Patches HERE.
Triangle Patch Function and Geometry Explained (See 1:18 time-mark):
NOTE: Despite what you may see in this video, you should ALWAYS insert brushes and patches from the chamber end first, using a fitted cleaning rod bore guide. With bolt-action rifles, NEVER insert a cleaning rod (with brush or jag) in through the muzzle. This may damage the delicate crown of your barrel.
The Triangle Patches work great with Boresmith’s patented dual-diameter bore brushes:
With the COVID-19 Pandemic, many shooting ranges remain closed or severely restricted. And in some cities there are still stay-at-home orders in place. If you’re an avid rifleman who enjoys shooting regularly, the Pandemic lock-down can bring withdrawal pains. The closure of outdoor ranges can mean months of forced inactivity, unless you have indoor shooting solution — such as this indoor airgun target backer system from Creedmoor Sports.
If you cannot practice at a nearby public range, Creedmoor Sports offers a great solution for those who want to shoot indoors — even in your own basement or garage.
Creedmoor’s patented 10m Air Gun Range provides a target holder and a curtain-type backstop capable of stopping pellets with a muzzle velocity up to 600 fps. The target boxes can be positioned at various heights for prone, kneeling, and standing. Creedmoor says the hardened steel target boxes provide 100% containment for any pellet passing through the target.
Creedmoor’s Air Gun Range is a proven, heavy duty product — the only Air Rifle target system ever tested and approved by the U.S. Military. This system is now being used in more than 800 schools nationwide, as well as the CMP shooting facility in Alabama. The 3-station range easily dis-assembles for transport and storage, fitting inside a 34″ x 10″ x 8″ carry duffle. The one-station range measures 84″ high x 30″ wide when assembled.
The Portable Air Gun Range comes with a durable curtain/ backstop that sets up quickly and easily. Velcro edging allows multiple curtains to be joined together. The curtain provides ample stopping power for air pellets. However, this is NEVER to be used with rimfire or centerfire rounds, or even high-energy pneumatic hunting rifles. This is for standard airguns only. That could be a $100 Crosman, or a $3600.00 Model 9003 S2 Anschutz:
Important news for 1000-yard benchrest competitors! The 2020 IBS 1000-yard National Championships will be held September 5 and 6, 2020 at the Vapor Trail Valley Range in Missouri. Take note — the IBS 1K Nationals were originally going to be held at the Hawks Ridge Range in North Carolina. So the event has moved from NC to Missouri, and will be held later in the year. This change was done because of uncertainties over COVID-19 public health policies/retrictions in North Carolina. Also, moving the Nationals to early fall gives more time to organizers to plan the event.
Forum member David 0306 from North Carolina observed: “As many of you have probably already heard, the 2020 1000-yard IBS Nationals has been cancelled for Hawks Ridge Gun Club in North Carolina. [Due to] uncertainty of what phase the NC Governor will have the state in, and the possibilities of going back into a stay-at-home order, the board at Hawks Ridge decided it was in the best interest of the shooters to cancel and allow another club to host the Nationals if possible. This will also help with travel plans, and getting time off from work. What I do know is Vapor Trail Valley has stepped up to the plate and has agreed to host the Nationals. Thank You Vapor Trail Valley and IBS shooters for your help and support through these difficult times.”
This site is for and about accurate shooters. So today we feature the short-range group Benchrest game, where it’s all about shooting tiny groups in the ones and even “zeros”. Seeing the tiny groups 6 PPC aces produce, it’s easy to think the precision is all about the equipment. But there is a lot more involved. A talented human still has to watch the flags, run the gun properly, and tune his loads for the conditions. Here are some tips from one of the world’s best benchresters, Charles Huckeba.
Texan Charles Huckeba was the top individual shooter at the 2013 World Benchrest Championships (WBC) held near Sydney Australia in October 2013. In this video, 2013 WBC Two-Gun Overall winner Charles shoots a 1/8th MOA group at 200 yards — “a little bitty dot” as a fellow Team USA shooter observes. That’s impressive. If you can describe Huckeba’s style in a nutshell it would be “smooth, consistent, and rapid but not hurried”.
Charles also employed some unusual hardware. In the video, take a close look at the joystick on the Farley Coaxial front rest. There’s no knob at the end. In its place is a small, wood ammo caddy. Charles removed the standard knob from the handle of his Farley rest and replaced it with a home-made wood block that holds cartridges for the record target. The 10.5-lb Light Varmint rifle is chambered in 6PPC with a BAT Machine Action and a composite wood and carbon-fiber stock.
Watch Charles Huckeba Shoot 1/8 MOA, 200-yard group at World Benchrest Championships
Here is the actual 200-yard, 5-shot group Charles shot in the video. Photo (by Stuart Elliot) taken through the lens of Huckeba’s 50X March scope (reticle has 1/16th MOA Dot).
Analyzing the Fine Points — What Makes Huckeba So Good
Short-range benchrest shooter Boyd Allen saw some interesting things in Huckeba’s WBC performance, as captured on video. Boyd noticed Huckeba’s smooth gun-handling and efficient loading. But Boyd also spied some interesting equipment, including an innovative joystick “handle-caddy”.
1. Low Friction Bags — When Huckeba slid his rifle, there was very little apparent friction. The front bag features the new 3M material (ScotchLite) on the sliding surfaces. The rear Protektor bag has ears of the same low-friction material.
2. Pause Before Chambering — While he was watching the flags and deciding when to start firing, Charles kept his first round in the action, but out of the barrel’s chamber, probably so as not to heat the cartridge and change the round’s point of impact.
3. Ammo Caddy on Joystick Arm – Charles shoots a Right Bolt/Left Port action, so he pulls his rounds with his left hand. Note that Huckeba’s record rounds rest in a small, wood ammo caddy attached to the end of the joystick shaft. Look carefully, you’ll see the wood ammo block in place of the normal black ball at the end of the joystick. That allows Charles to pull shots with the absolute minimum of hand movement. Ingenious! Huckeba is very fast, with a great economy of motion. I believe that because his ammo was literally at hand, Charles was better able to keep his focus on aiming and the flags.
4. Smooth-Cycling BAT Action — Note how smoothly Huckeba’s action operates. When Charles lifts the bolt handle (to extract a round and cock the firing pin), this does not disturb the rifle. Likewise, as he closes the bolt, the gun doesn’t wobble. The smooth action allows Charles to hold point of aim even when shooting relatively quickly. Huckeba’s BAT action is chrome-moly steel. Some shooters believe this metal makes for a smoother action than stainless steel or aluminum.
5. Long-Wheelbase Stock — The wood and carbon fiber stock is light, long, and stiff. Yet, importantly, the stock is also well-damped. The longer-than-average stock length (with extended forearm) seems to help the gun track well without jumping or rocking. The longer forearm allows a longer “wheelbase”, effectively shifting the weight distribution rearward (less weight on the front, more weight on the rear). This places a greater share of the gun’s weight on the rear bag, as compared to a more conventional benchrest stock. Huckeba’s stock, built by Bob Scoville, is at the cutting edge of short-range benchrest design. Its light-weight balsa wood and carbon fiber construction provides a combination of stiffness and vibration damping that allows its relatively long fore-end to be fully utilized to increase the weight on the rear bag (always an issue with 10.5-pound rifles).
To learn more about this benchrest stock design, read the comments by stock-builder Bob Scoville in our PPC with Pedigree story in our Gun of the Week Archives. Bob observed:
“There is a lot more to the structure of the stocks than meets the eye. The carbon fiber skin with which I cover the stocks creates a light, tough exterior surface. However, this contributes very little to the overall performance of the stocks. The real strength and stiffness is the result of an internal beam utilizing balsa core/carbon fiber technology.
This type construction can be found in aircraft, race cars, powerboats, and sailboats. It is interesting to note, balsa has the highest strength to weight ratio of all woods and carbon fiber is one of the lowest stretch (modulus of elasticity) relative to weight of all materials. The marriage of these two materials is common in the high-performance world. Additionally, balsa is used commercially for vibration dampening and sound reduction.”
Video find by Boyd Allen. Video by Stuart Elliot of BRT Shooters Supply, Brisbane, Australia.
Kirsten Weiss knows a thing about accuracy. She won the 2012 NRA Three-Position Women’s Smallbore Championship, while finishing as the National Overall Woman Champion. She used to shoot with the American team in top-level World Cup competition. Kirsten started shooting fairly late — at age 16. Despite her relatively late start, she earned a place on the University of Nebraska shooting team. That literally opened up a new world for Kirsten: “During the course of my career, I’ve had a lot of success. I’ve gone to World Cups… in Zagreb, Croatia, in Munich, Germany. I’ve won National Championships, and got on to the U.S. Olympic short list, so it’s been a good career.”
In these three videos, Kirsten offers key tips on accurate shooting. In the first video she explains how to get and maintain the proper cheek weld on your rifle. In the second, Kirsten talks about canting error — how having inconsistent side-to-side tilt on your rifle. In the third video, Kirsten explains the importance of proper trigger placement.
Proper Cheek Weld
No matter what your discipline — smallbore, silhouette, High Power, F-Class, or even PRS — it’s vital to have a consistent cheek weld for every shot. You want your head to be in the same position on the stock each time.
In this video, Kirsten explains how to find the best position for your head on the stock, which may require adjusting the cheekpiece and/or length of pull. Then Kirsten demonstrates how to maintain consistent cheek weld shot after shot.
Consistent Rifle Cant (Tilt from Centerline)
Kirsten says most training manuals don’t explain rifle cant: “You won’t find this shooting technique just anywhere. Most shooters don’t even think about it — and they’re missing out. Proper Rifle Cant or Gun Cant (also known as cant error or even scope cant) is a complicated topic, but I’ll explain it simply — and how to simply avoid cant error.”
Want to know how to actually aim a gun right? This accuracy tip covers a crucial aspect of marksmanship. If you cant your rifle inconsistently from shot to shot, the point of impact will change, even with “perfect aim”. This is another episode in Kirsten’s How to Shoot Awesomely video series.
Proper Trigger Finger Technique
Kirsten tells us: “Finger placement on the trigger might not seem like a big deal, but it actually is. The reason for this is because, depending on where your index finger is placed on the trigger, [this] translates to different muscle interactions with the gun.” Watch this video to see Kirsten demonstrate proper finger placement (and explain problems caused by improper finger positioning).
When you pull the trigger, you only want to engage the last section of your finger, in order to avoid unwanted muscle engagement and to achieve a smooth shot. Remember there is a “sweet spot” between the crease (first joint) and the tip of the finger. If you position the trigger in that “sweet spot”, you should see an increase in your accuracy. Don’t make the mistake of putting the trigger in the crease of your finger, as shown below.
A fire in the home is always to be feared. And a fire in your reloading room can be disastrous. Near your reloading bench you probably have flammable solvents, and maybe gunpowder. What would happen if an electrical fire started in your reloading room? Would you be alerted? Do you have a proper fire extinguisher at hand?
Here’s a true story from Forum Member Joe O. (aka “Joecob”) that provides a valuable safety lesson. After Joe started up his old tumbler, an internal connector worked loose, causing an arc which started a fire in his basement reloading area. Luckily Joe had a functioning smoke detector, and a fire extinguisher.
Very few of us would worry about fire when we plug in a tumbler or other AC-powered reloading tool. But there is always the possibility of a malfunction and a fire. Quick thinking (and a handy extinguisher) prevented serious damage to Joe’s reloading room and house — but things could have been worse (much worse), had Joe not responded quickly.
Fire in the Reloading Room — Report by Joecob
The day before ‘Sandy’ hit I was cleaning brass the way I always have. I set the vibratory tumbler on the back of my reloading bench in the basement. I loaded the media hopper with 40 fired empty brass cases (and walnut media), plugged the cord in, turned the tumbler on and went back upstairs to watch TV. I could hear the tumbler running in the background.
About half an hour later I heard the basement smoke alarm go off. I ran downstairs. Flames were licking from the melting plastic of the tumbler.
I grabbed the nearby ABC cannister extinguisher and squirted out the fire and soaked the charred bench areas with water. Good thing I had the extinguisher! And I was glad I religiously store powder and primers properly — away from the bench (and everything else).
What caused the fire? It looks like an internal AC connector finally vibrated loose enough to arc and ignite the plastic. WHEH! I had been using that thing for 25 years the same way without mishap. Guess I should have known to periodically check the guts of a thing that plugs in and vibrates for a living?
Today I went out and bought a new even bigger ‘Pro’ ABC extinguisher, plus a dual-detector smoke alarm, and an ultrasonic cleaner. That experience was scarier than the storm. I hope this true account might help someone else to avoid a bad experience.
In his account, Joe refers to an “ABC” cannister fire extinguisher. The “ABC” refers to the fire classification rating: Class A (trash, wood, and paper), Class B (liquids and gases), and Class C (energized electrical equipment) fires. There are many brands of ABC-rated extinguishers.
The rechargeable Kidde 210 unit (sku 21005779) contains four pounds of a multipurpose monoammonium phosphate dry chemical extinguishing agent. It has a discharge time of 13 to 15 seconds, a discharge range of 10 to 15 feet, and an operating pressure of 100 PSI. The seamless aluminum cylinder measures 4.5 inches in diameter and 15.7 inches tall. The Kidde 210 has a 6-year limited warranty. This is Amazon’s #1 Best Seller among Fire Extinguishers.
At the request of our readers, we provide select “Deals of the Week”. Every Sunday afternoon or Monday morning we offer our Best Bargain selections. Here are some of the best deals on firearms, hardware, reloading components, optics, and shooting accessories. Be aware that sale prices are subject to change, and once clearance inventory is sold, it’s gone for good. You snooze you lose.
1. Cabela’s — Bergara B-14 HMR, $949.99
⏺ Good Ergonomics, Works for Hunting plus PRS Factory Class
Bergara rifles offer excellent value for the money. They combine accuracy, good ergonomics, and smooth function at a lower costs than many other brands. If you’re looking for a new rifle that’s capable of hunting, PRS competition, or target shooting, check out the Bergara B-14 HMR now on sale. Available in 6.5 Creedmoor or .308 Win for $949.99, the B-14 HMR features a quality synthetic stock with adjustable cheek-piece. The 24″ barrel has a threaded muzzle, so you can add a muzzle brake or suppressor.
2. Amazon — Frankford Arsenal Perfect Seat Priming Tool, $69.79
⏺ Precise Depth Control, 12 Shell Holders, Quick-Change, Carry Case
Seating primers to a consistent depth helps deliver enhanced accuracy and low ES/SD. However, most priming systems don’t allow precise depth control. If you’re looking for a priming tool that allows you to adjust primer seating depth, check out the Frankford Arsenal Perfect Seat Hand Primer. This tool comes in a protective case along with a full set of case holders and primer flip tray. A quick thumb release system allows you to switch from small to large primers quickly.
3. Precision Reloading — H4350 and Reloder 16 in Stock
⏺ Great Temp-Stable, Match-Grade Powders in Stock
The most popular powders, such as H4350 and Reloder 16, can be hard to find. But we’ve located these outstanding temp-stable powders at two leading vendors. Right now Precision Reloading has both Hodgdon H4350 (1-lb and 8-lb) and Alliant Reloder 16 (1-lb) in stock. In addition, Powder Valley has popular H4350 in stock (1-lb and 8-lb). These powders are both great choices for 6.5 Creedmoor, .284 Win, and other match cartridge types.
4. Graf & Sons — 25% Off All Sightron Scopes
⏺ Great 25% Sale! Sightrons Rival Optics Costing Hundreds More
Need a high-quality optic for your match rifle or hunting rig? Looking for a specialized “big wheel” scope for Field Target airgun competition? Sightron offers a wide range of quality scopes at affordable prices. And now the deals are even better. Right now Grafs.com is offering 25% Off ALL Sightron scopes in stock. This sale is good through 11:59 pm CT on July 10, 2020.
5. Amazon — Lyman Xpress Case Trimmer, $114.99
⏺ Great Tool — EZ Length Adjust, Variable Speed, Carbide Cutter, 10 Bushings
Trimming cases to length is a critical for precision reloading. Unfortunately, many trimmers are inefficient and/or clunky. If you want a fast, easy, and precise way to trim brass look no further than the Lyman Xpress Case Trimmer. This boast a super-sharp carbide cutter head plus a variable speed control. The unit ships with 10 shoulder bushings to cover most cartridge types. The carbide cutter trims fast and clean.
6. Amazon — Teslong Rod-Type Digital Borescope, $79.99
⏺ Handy Rod Borescope with Sharp Digital Images and Video
Teslong digital borescopes have been a huge success and earned high praise from our Forum members. First there was the cable-type plug-in model, then a Wifi Teslong that works with all types of mobile devices. The latest Teslong features a metal shaft, with length markings. This makes it easier to inspect your bore with precision. This compact, electro-optical, Rod-type Borescope ($79.99) outputs sharp, high-rez images and VIDEO to desktop computers, laptops, as well as Android tablets and smartphones.
7. Amazon — Frankford Arsenal or Lyman Brass Tumbler Sale
⏺ Great Sale Pricing, Choose Lyman or Frankford with Clear Top
⏺ Huge Discounts on Weaver Tactical, Hunting, and Competition Optics
Weaver scopes have always been a top optics option. Weaver offers models for just about any discipline. If you’re in the market for a new scope check out the amazing Weaver Scope Blowout SALE at Natchez. Natchez has a good assortment of quality Weaver scopes at crazy low prices up to 55% off. NOTE: There may be changes in Weaver scope production. Contact Bushnell for ongoing warranty policies.
9. Brownells — TriggerTech Trigger Sale
⏺ Good Selection for ARs and Rem-Compatible Bolt Guns. Save 25-35%
TriggerTech makes quality trigger with crisp breaks and adjustable pull weights. With a protectice housing, tThese triggers are very resistant to dirt and debris. If you’ve been looking for a new trigger, check out the TriggerTech Trigger Sale at Brownells. There are substantial discounts. For example the AR15 Independence trigger is discounted from $229.99 to just $149.99 — a 35% savings.
10. Midsouth Shooters Supply — Berger Ammo Sale
⏺ True Match-Grade Factory Ammo with Lapua Brass and Berger Bullets
Berger Bullets is a renowned bullet-maker. But did you know Berger makes loaded ammunition as well? Available in many calibers for both hunting and target shooting, Berger ammo is a great choice for those who want quality without hand-loading. Midsouth Shooters is running a Berger Ammo Sale. You’ll find 6.5 Creedmoor, .260 Rem, .308 Win, .300 Win Mag, .338 LM and other popular types. This ammo shoots great — check out this Berger 6.5 Creedmoor Ammo Test.
Looking to acquire a handgun for personal protection of home and family? There are countless options on the market. Your buying decision may be simplified by seeing what other consumers have chosen, as revealed by nationwide sales trends. You can now check firearms sales figures using “Gun Genius”, a new data-crunching service of Gunbroker.com. On GunGenius.com you can select any type of firearm (handgun, rifle, shotgun)* and see the top sellers for that category. Here are the top-selling semi-auto handguns, new and used. There are separate listings for revolvers.
Here are the FIVE (5) top-selling NEW semi-auto handguns for JUNE 2020:
Here are the FIVE (5) top-selling USED semi-auto handguns for JUNE 2020:
It’s notable that three of the top five used handguns are Glocks: G17, G19, and G22. Glocks are rugged and reliable, though we don’t like the ergonomics.
*Chose semi-auto pistols, revolvers, semi-auto rifles, bolt-action rifles, lever-action rifles, single-shot rifles, semi-auto shotguns, pump shotguns, and more. You can also filter for sales trends (upwards and downwards). Drill down to see detailed product specifications and current prices.
This new rifle may interest game hunters. For around $1120 (street price) the new Howa Carbon Kratos rifle combines an excellent Hogue camo stock with a carbon-wrapped barrel. This allows a rifle that is significantly lighter than a conventional hunting rifle. The carbon-wrapped barrel also features a threaded muzzle (with cap), so you can easily fit a suppressor or muzzle brake.
Howa’s new Carbon Hogue Kratos rig will first be offered in .308 Winchester, followed by 6.5 Creedmoor, 6.5 PRC, and 300 PRC chamberings. The new rifle features a 24″ Howa barrel that is carbon fiber-wrapped and threaded for suppressors or muzzle brakes. The Hogue stock is pillar-bedded and dipped in the effective Kratos camo pattern. Also available is a scoped package with a 4-16×44 Nikko Sterling Diamond FFP scope. Although the scope package adds just $220 to the MSRP, we recommend getting the bare rifle and then adding a higher quality optic. You’ll be happier in the long run.
Howa Carbon Fiber Hogue Kratos Features
Howa 1500 Action with 3-Position Safety
Howa 24″ Carbon Wrapped Barrel, threaded with cap
Excellent 2-Stage HACT Trigger
Sub-MOA at 100 yards Guarantee
Optional Scope Package with 4-16×44mm Nikko Stirling Diamond FFP
Lifetime Warranty on Rifle and Optic
COMMENTARY: We’ve shot Howa rifles and can attest that the 1500 action cycles smoothly and the HACT 2-Stage trigger is very good for a factory gun. This is definitely a viable hunting option with a high-quality stock and weight savings via the carbon-wrapped barrel. You can pay significantly more and not get a better hunting rig. Put the savings into a good Laser Range Finder.
MSRP – $1,379 for Howa Hogue Kratos Rifle Only model HGCF308KTS — .308 Win
MSRP – $1,599 for Howa Hogue Kratos Scoped Package option HGCF308KTSP — .308 Win
For more information on all Howa rifle offerings or to request a FREE 2020 catalog, visit LegacySports.com.
With the COVID-19 Pandemic, many shooting ranges remain closed or severely restricted. And in some cities there are still stay-at-home orders in place. If you’re an avid rifleman who enjoys shooting regularly, the Pandemic lock-down can bring withdrawal pains. The closure of outdoor ranges can mean months of forced inactivity, unless you have indoor shooting solution — such as this indoor airgun target backer system from Creedmoor Sports.
3. Ammo Caddy on Joystick Arm – Charles shoots a Right Bolt/Left Port action, so he pulls his rounds with his left hand. Note that Huckeba’s record rounds rest in a small, wood ammo caddy attached to the end of the joystick shaft. Look carefully, you’ll see the wood ammo block in place of the normal black ball at the end of the joystick. That allows Charles to pull shots with the absolute minimum of hand movement. Ingenious! Huckeba is very fast, with a great economy of motion. I believe that because his ammo was literally at hand, Charles was better able to keep his focus on aiming and the flags.
A fire in the home is always to be feared. And a fire in your reloading room can be disastrous. Near your reloading bench you probably have flammable solvents, and maybe gunpowder. What would happen if an electrical fire started in your reloading room? Would you be alerted? Do you have a proper fire extinguisher at hand?
I grabbed the nearby ABC cannister extinguisher and squirted out the fire and soaked the charred bench areas with water. Good thing I had the extinguisher! And I was glad I religiously store powder and primers properly — away from the bench (and everything else).
