Wipe-Out foam bore cleaner is a product we’ve used with great success on many rifles. With sufficient dwell time, it removes both carbon and copper fouling. You can combine it with Wipe-Out Accelerator or Patch-Out liquid to speed up cleaning time. Many shooters, including this editor, find that bore-brushing has been virtually eliminated with the regular use of Wipe-Out. (With some barrels however, you may still have to brush or use a bore paste if you notice stubborn carbon build-up in the throat area.)
CLICK HERE for full official instructions on use of Wipe-Out foam applied from the muzzle or the breech.
Method One: Apply Through Muzzle
Out standard procedure with Wipe-Out is to insert an O-ring-sealed cleaning rod guide into the chamber and then squirt through the muzzle in short puffs. Put a towel or rag on the comb of your stock and watch for a little bit of foam to exit the rod guide. We usually wait 30 minutes for the bubbles to dissipate, then do a second foam application. Be sure to clean off any excess foam before it drips on your stock. It is important to keep the foam off fine wood or paint finishes.
Our actual routine normally starts with 3-4 wet patches with Carb-Out (to get the loose black stuff out), followed by the two foam cycles as explained above. Then we plug both ends of the barrel, drive home from the range and dry-patch out on arrival at the house. If the gun is going to be used again soon, that’s all we do. If there will be long-term storage we’ll run some Eezox down the bore.
Method Two: Apply Wipe-Out from Breech
You can also apply Wipe-Out from the breech. To allow breech-first application, Wipe-Out cans now come with a short plastic tube and a plastic tip that fits in your chamber. These can also be purchased separately for $2.50. However, we’ve found the plastic tip is too big for some chambers and it is not always easy to get a good, secure seal even if it does fit. Jason Baney has come up with a solution. READ Jason’s Wipe-Out Article.
Use Fitted Tubing for Breech-First Applications of Wipe-Out
You can apply Wipe-Out through the breech very effectively if you use fitted, plastic tubing. While this works well for bolt-actions, breech application is particularly handy for the Garand, M1A and other semi-autos. Jason Baney has written a short article describing this process. In a nutshell, you need one piece of tubing that fits the chamber tightly and then connects with a second, smaller diameter tube that attaches to the Wipe-Out can. This avoids any “over-spray” of foam in the action area, providing a clean, simple solution. Just squirt for a second or so, and wait for white foam to come out of the muzzle. Be sure to keep Wipe-Out off fine wood stocks.
At the request of our readers, we provide select “Deals of the Week”. Every Sunday afternoon or Monday morning we offer our Best Bargain selections. Here are some of the best deals on firearms, hardware, reloading components, optics, and shooting accessories. Be aware that sale prices are subject to change, and once clearance inventory is sold, it’s gone for good. You snooze you lose.
NOTE: All listed products are for sale to persons 18 years of age or older. No products are intended for use by minors.
1. EuroOptic — Tikka T3x Rifle Blow-Out Sale — Save 35%
⏺️ » Tikka makes great hunting rifles now offered at major savings
With this Blow-Out Sale at EuroOptic.com, you can save $120-$500 on quality Tikka T3x hunting rifles, starting at just $499.99. Multiple models are on sale including T3x Lite, T3x Lite Compact, T3x Lite Stainless, T3x Hunter, T3x Laminated, and T3x RoughTech. Both right-hand and left-hand versions are offered. The Hunter models feature a handsome wood stock. These rifles can deliver sub-MOA accuracy with good hand-loads.
2. Creedmoor Sports — Berger Bullet Sale, Save up to 20%
⏺️ Good discounts on very large selection of Berger bullets
Now’s the time to get components, with the competition season getting underway. And right now Creedmoor Sports is running a major Berger Bullet Sale with quality Berger bullets from .17 to .30 calibers in a wide variety of hunting and match types. Choose target hybrids, varmint bullets, Elite Hunters or other bullet types for your next match or hunt. Many of the most popular .22-Cal, 6mm, 6.5mm, 7mm, and .30-Cal match bullets are on sale.
3. Sportsman’s WH — Springfield Armory XD-M Elite, $379.99
⏺️ Great deal on excellent 9mm pistol complete with Crimson Trace optic
Here’s a great deal on a high-quality Springfield Armory XD-M Elite 9x19mm pistol complete with a Crimson Trace 1500 Red Dot sight. With this current $379.99 sale price you save $220 (37%). That’s a terrific deal on a pistol with excellent owner reviews: “Great value and a great pistol. 100% reliable and accurate”; “Very happy with this purchase”.
4. Sportsman’s WH: SIGnature Event Optics Sale, Save 20-40%
⏺️ Discounts on scopes, rangefinders, red dots, plus FREE Gift Cards
Head over to Sportsman’s Warehouse for major savings on SIG Sauer scopes, rangefinders, and Red Dot optics. And now through 4/20/2025, you’ll receive a $10 Sportsman’s Warehouse Gift Card for every $100 spent on SIG Sauer items. The eGift Card will be sent once SIG Sauer items are shipped. This eGift Card offer applies to SIG Sauer firearm sales as well as SIG Sauer optics. And with many products Sportsman’s Warehouse is currently offering Free Shipping with orders over $49.00.
5. Midway USA — Walker’s Electronic EarMuffs on Sale
⏺️ Major savings on popular electronic hearing protection
6. Midsouth — Lyman Gen 6 Powder Scale/Dispenser, $219.99
⏺️ Good advanced powder dispenser now $40 Off plus FREE Shipping
Here’s a good, modern powder scale/dispenser offered with a HUGE discount. At Midsouth, the Lyman Gen 6 Compact Powder Dispenser System is now $40 Off with FREE Shipping. So your total price, delivered, is $219.99 — a great deal. This unit is accurate to +/- 0.1 grains and can use any type of smokeless powder. It has a fast warm-up, anti-static/anti-drift technology, with sophisticated electronic shielding to resist interference from other electronic devices. This unit comes with calibration weight, powder tray, and cleaning brush.
⏺️ » Incredibly low price on a good home defense shotgun
If you’re looking for a rugged 12ga shotgun for home defense — here is the deal of the decade. CDNN Sports is now selling a Dickinson XX2T 12ga Pump Shotgun for just $139.99, an amazingly low price. This pistol-grip shotgun works with 2 3/4″ or 3″ shells and has an 18.5″ barrel with factory muzzle brake. This XX2T, with shielded tactical iron sights, is $110 off the regular $249.99 price.
8. Midsouth — Aguila .22 LR ammo, 2000-rd case, $114.99
⏺️ Great 2000-round .22 LR bulk pack, super-low price
Modern .22 LR rimfire ammo is way cheaper than centerfire ammo, which can cost $1.30 or more per round for your own handloads, given the high costs of bullets, powder, and primers. Here’s a great deal — Midsouth offers 2000 rounds of Aguila .22 LR for only $114.99. This 38gr High Velocity Copper Plated Hollow Point is sold in a 2000-rd case. The $114.99 price works out to just $.06 (six cents) per round.
9. Amazon — Tactical Shooting Mat & Rest Bags, $29.99
⏺️ Handy shooting mat with two bags — all for under $30
Shooting prone requires a good shooting mat. And it helps to have front and rear bags when not sling-shooting. One budget-priced option is this DGVR Tactical Shooting Mat (#ad) set that comes with both front and rear bags. Get the mat and both bags for just $29.99 on Amazon (#ad). The bags are made of 600D oxford but do NOT come filled. The 1000D Nylon shooting mat is waterproof, and boasts a non-slip, wear-resistant coating plus a handy carry strap.
10. MidwayUSA — Tipton Jag Kit Brass or Nickel 15-20% Off
⏺️ Very useful kit with 13 different size jags
If you shoot a variety of calibers, you need one of these Jag Kits, now 25% Off. You get 13 different diameter jags in a fitted case for under $17.00. We like the Nickel-Plated Ultra Brass Jags (20% off price $19.99) because you don’t get “false positive” blue from your solvent interacting with the jag itself. But the regular Solid Brass Jags (15% Off price $16.99) also work great and some folks think they are more durable. We own these Jag kits and use them for everything from a .17 HMR up to a 45/70. Both kits contain 13 jags covering these calibers: .17, .20, .22, .243/6mm, .25/6.5mm, .270/7mm, .30, .338/8mm, .35/9mm, .375, .40, .44 and .45.
As an Amazon affiliate, this site can earn revenues through sales commissions.
The National Shooting Sports Foundation (NSSF) has prepared tips for gun owners transporting firearms in their vehicles. Whenever you are driving with guns (of any kind), the firearms should be transported securely. In some states, the firearms must be in locked cases inside the vehicle. And, with the rise of break-ins on parked vehicles, it’s important to keep gun cases out of sight if possible. This article has tips on safe and secure gun transport.
HERE Are Key Guidelines for Safe, Secure Handling of Firearms in Vehicles:
• Take note of and safely control the muzzle direction of firearms in vehicles. This is one of the main rules of gun safety and applies to the inside of vehicles as well as any other location.
• When finished using your firearm outside your vehicle, unload it before you re-enter your vehicle.
• Even after a long hunt or a day in the sun at the range, always check, and then double check, that guns are unloaded before placing them in a car or truck.
• Be very careful if you must unload a firearm in the confined space of a vehicle so as not to have an accidental discharge. If your location allows, it is safer and easier to unload the firearm outside the vehicle.
• Never leave firearms in parts of the vehicle accessible to children or pets.
• Keep firearms and ammunition out of sight to avoid tempting thieves.
• Use secure temporary storage for firearms in vehicles.
• A lockable gun case or a lock box may be the most practical choice to securely store a gun in a vehicle. These come in a range of prices and models.
• If you’re concerned about quick access to your firearm, many types of lockable safes allow for extremely fast access of your gun while at the same time helping to prevent unauthorized access.
• Secure the lock box to the vehicle, if possible. Some companies make custom concealed compartments for specific model vehicles.
Storing Firearms in Vehicles to Prevent Theft and Misuse
We travel with our firearms all the time, taking them to the range, on hunting trips or carrying them on our person, as permitted by law. When you are transporting guns, the last thing you want is to have your gun stolen and potentially misused by a criminal. In some states, you could even be subject under the law to serious penalties and fines for failure to properly secure a firearm. Unfortunately, thefts of firearms from vehicles are on the rise. Thieves commonly steal cars and trucks even when they don’t obviously contain firearms — a reminder that vehicle door locks are not totally secure.
When you are not in your vehicle, all firearms should be placed in locked storage and out of sight. Locking the doors on your vehicle does not constitute secure firearm storage. As one writer put it: As one writer put it: “Cars and trucks aren’t safes. And they’re not holsters. They’re not storage containers.”
The glove compartment or console of your vehicle, even if lockable, should not be considered a secure storage device either, as it can be pried open quickly and is the first place a thief might look. If you need to leave a handgun in a vehicle, we recommend putting the guns in secure case, preferably out of sight. Many vehicles have a compartment, above the spare tire storage recess, which can be secured.
For our readers who are stuck at home under government orders, we are reprising a video feature about hunting in Norway. For those whose horizons have been limited due to the “shelter at home” response to the Coronavirus pandemic, we offer this getaway to scenic Vesterålen in northern Norway…
This is one of the finest shooting videos we’ve ever seen. Set in the scenic Vesterålen archipelago of northern Norway, this high-quality 15-minute video is part National Geograhic travelog, part ballistics lesson, part gear review. Given the current COVID-19 lockdowns, we wish we had the opportunity to join Ulf Lindroth and Thomas Haugland on their remarkable shooting adventure. This video was originally created for Great Britain’s Fieldsports TV Channel.
This is an outstanding video, recommended for anyone interested in long-range hunting.
Long range shooters Lindroth and Haugland traveled to the Arctic Circle to field test a new .338 LM Blaser R8 (in GRS stock) fitted with a Zeiss Victory V8 4.8-35x60mm scope. (Ammo is Norma-brand .338 Lapua Magnum). The video shows how they confirm the ballistics of the Norma factory ammo in the Blaser R8 rifle system.
Ulf and Thomas initially test out the system confirming drop at multiple yardages, and then use the rifle for practical accuracy. Ulf says: “If you know your hunting will demand a long shot, and you want to push the limit but still be sure to make the first-shot kill… If you want to do an ethical hunt, if you want to push that limit, you have to do [this kind of testing].”
Ulf Lindroth (above) observed: “We shot [at 808 meters] observed the misses, clicked our way into the target, and now we have the true drop at that distance… in this air pressure, in this temperature. From there we can start working to find our TRUE trajectory. And when we have THAT… we can get serious about some target shooting.”
.338 Lapua Magnum — Big-Bore High-Performance Cartridge
From WikiPedia: The .338 Lapua Magnum (aka 8.6×70mm) is a rimless, bottlenecked, centerfire rifle cartridge. It was developed during the 1980s as a high-powered, long-range cartridge for military snipers. Due to its use in the War in Afghanistan and the Iraq War, the cartridge has become widely available. The loaded .338 LM cartridge is 8.6 mm (0.34″) in diameter and 93.5 mm (3.68″) long. Muzzle velocity is dependent on barrel length, seating depth, and powder charge, and varies 2,890 fps to 3,000 fps for commercial loads with 250gr bullets.
Our friend Jim See of Elite Accuracy LLC tested the depth-adjustable hand priming tool from Frankford Arsenal. This product, called the Platinum Series Perfect Seat Hand Primer has some unique features. Primer seating depth can be adjusted with a handy wheel in the tool’s center handgrip. Each “click” of the wheel moves the primer post .001″ (one one-thousandth of an inch). Additionally, the design of the case-holder allows quick and easy removal of a primed case. The unit ships with a full set of shell-holders to match all types of cases. Like many other hand priming units, the primers are loaded into a flip tray that attaches to the head of the tool.
Here is Jim See’s quick review of the Frankford priming tool:
“The Frankford Arsenal perfect hand-priming tool is legit. The tool is built heavy and strong. The only plastic parts in it are the tray and lid. The [primer] seating depth adjustment… is simple and accurate. Easy to operate. I primed 1000 cases, averaging 23 per minute. I adjusted the depth of seating between two different lots of brass in seconds. The system seats primers easily with one hand operation. The cases slide out on their own after seating. Insert, seat, reach for a new case at the same time as you are operating the lever, case slides out and you are inserting the next piece.”
Overall, Jim was “Super impressed with the quality and the results. This thing is super smooth — way less pressure needed than my Lee or RCBS. It’s a lot faster too.” Jim add that one can switch from small to large primer posts in 10-15 seconds.
This Video Shows the Frankford Priming Tool in Operation:
Even with premium brass you may want to adjust your primer seating depth: “Every thing has a tolerance that is acceptable in manufacturing. If primer pocket depth has a .005″ tolerance and the primers themselves have a .002″ tolerance you can see why adjustments would be needed. In this case the two lots were manufactured on year apart. Could you expect them to be identical?”
The digital archives of Shooting Sports USA magazine (SSUSA) features an Expert Forum on Wind Reading. This outstanding article on wind reading starts off with a section by ballistics guru Bryan Litz, author of Applied Ballistics for Long-Range Shooting. Then four of the greatest American shooters in history share their personal wind wisdom. Lanny Basham (Olympic Gold Medalist, author, Winning in the Wind), Nancy Tompkins (Past National HP Champion, author, Prone and Long-Range Rifle Shooting), David Tubb (11-Time Camp Perry National Champion), and Lones Wigger (Olympic Hall of Fame) all offer practical wind-reading lessons learned during their shooting careers.
Whether you shoot paper at Perry or prairie dogs in the Dakotas, this is a certified “must-read” resource on reading the wind. Here is a sample selection from the article:
Shooting Sports USA magazine (SSUSA) has a modern, mobile-friendly website with tons of great content. Log on to www.ssusa.org. There you’ll find current news stories as well as popular articles from the SSUSA archives. The SSUSA website also includes match reports, gear reviews, reloading advice, plus expert marksmanship tips from the USAMU.
The question of barrel break-in is controversial. Some folks advocate an elaborate, lengthy cycle of shooting and brushing, repeated many times — one shot and clean, two shots and clean and so on. This, it is argued, helps barrels foul less and shoot more accurately. Others say minimal break-in, with patching and brushing after 10-15 rounds, is all you need. Still others contend that break-in procedures are a total waste of time and ammo — you should just load and shoot, and clean as you would normally.
We doubt if there will ever be real agreement among shooters concerning barrel break-in procedures. And one must remember that the appropriate break-in procedure might be quite different for a factory barrel vs. a custom hand-lapped barrel. This Editor has found that his very best custom barrels shot great right from the start, with no special break-in, other than wet patches at 5, 10, and 15 rounds. That said, I’ve seen some factory barrels that seemed to benefit from more elaborate break-in rituals.
What’s the best barrel break-in procedure? Eric Mayer of Varminter.com decided to ask the experts. Eric interviewed representatives of three leading barrel manufacturers: Krieger, Lothar-Walther, and Shilen. He recorded their responses on this video. In order of appearance, the three experts are:
Shilen, Krieger, and Walther Experts Talk about Barrel Break-in
Do I Need to Break-In a New Rifle Barrel?
Eric Mayer of Varminter.com says: “That is a simple question, [but it] does not necessarily have a simple answer. Instead of me repeating my own beliefs, and practices, on breaking-in a new rifle barrel, I decided to answer this one a bit differently. While we were at the 2016 SHOT Show, we tracked down three of the biggest, and most popular, custom barrel makers in the world, and asked them what they recommend to anyone buying their barrels, and why they recommend those procedures. We asked the question, and let the camera run!” Launch the video above to hear the answers — some of which may surprise you.
Barrel Break-in — Initial Inspection and Cleaning
This video explains that you should always inspect and clean the bore of your barrel before sending rounds through it. There may be remnants of the production process, such as lapping residues, that you’ll want to get out of the bore. We’ve even seen a few tiny metal pieces in some factory barrels. And it’s always wise to borescope a new barrel to see if there are visible defects in the rifling such as lands that have flawed edges — we’ve seen that on some cheaper barrels.
Barrel Break-In — Ian Klemm’s Surprising Observations
Here’s a 10-minute Vortex Nation interview with Ian Klemm. Ian, a 4-Time F-TR National Champion is one of America’s best long-range shooters. In this video, Ian explains his approach to barrel break-in, which may surprise you. Does barrel break-in even matter? Conventional wisdom says “Yes” and perhaps there’s some truth to that, but Ian argues that break-in is NOT nearly as important as the internet wants you to believe. Ian believes that you don’t need to waste a ton of time/ammo to get your barrel ready to shoot extremely accurately. This may be particularly true with premium hand-lapped custom barrels.
Barrel Break-In Procedures with Keith Glasscock
Keith Glasscock is also one of America’s greatest F-Class shooters who has finished second at the Nationals multiple times. Keith is also a highly-respected wind coach who has a popular YouTube video channel, Winning in the Wind. In this video, Keith explains his procedure for breaking-in his match barrels. He starts by bore-scoping the barrel and cleaning it. If he finds some burrs he may use some JB Bore Paste, a patch, and a worn brush and “give that throat a little scrub” (See 1:30 time-mark). He used different stroke lengths to avoid putting a “step” in the throat. When he’s satisfied he goes to the range. He fires the first five rounds, then cleans. He then fires quite a few rounds before cleaning the barrel again and beginning load development (See 8:25 time-mark).
General Barrel Break-in Procedures Recommended by Brownells
Brownells Gun Techs Steve Ostrem and Caleb Savant tackle a thorny topic: breaking in a new barrel. What IS breaking-in a barrel? And WHY do it? The rifling of a freshly machined barrel has microscopic burrs and sharp edges. “Breaking-in” is the process of putting bullets down the bore to smooth out those rough spots. The goal is to round down the sharp edges so they’re not stripping copper off a bullet as it travels the bore, which leads to fouling that leads to reduced accuracy and inconsistent groups. In a very minor way, you’re actually lapping the barrel. The breaking-in process works best on cut-rifled and button-rifled barrels. Cold hammer-forged, chrome-lined, or nitrided barrels — such as commonly found on AR-15s — may not benefit much from the process. Pistol barrels really don’t need to be broken in because larger-diameter bullets are not so much affected by tiny variations in the bore. Likewise, break-in is more helpful for a .17, .20, or .22 caliber rifle than a .45 caliber rifle.
George Gardner of G.A. Precision Talks About Barrel Break-In
G.A. Precision’s George Gardner is a leading figure in the PRS/NRL world. In this video, George makes the valid point that not all barrels require the same amount of break-in. George says some barrels require very little break-in, while others benefit from a more elaborate break-in process that helps reduce future copper and powder fouling. He calls this “seasoning” the barrel so it fouls less. For a typical barrel, George’s recommended process (4:25 time-mark) starts with one shot, then clean for three one-round cycles. This is followed by three shots then clean, with repeat 3-shot cycles if need. For cleaning George prefers nylon brushes (5:50 time-mark). NOTE: George also makes a very important point — you MUST swab the chamber and get it dry between cleaning cycles (5:30 time-mark).
Mark your calendars for the return of the Civilian Marksmanship Program’s Bianchi Cup International Pistol Tournament. The second longest-running pistol championship in the world, the 2025 CMP Bianchi Cup is set to run May 20-23, 2025 at the Green Valley Rifle & Pistol Club in Hallsville, Missouri.
About the CMP Bianchi Cup
The Bianchi Cup International Pistol Tournament was first held in 1979, making it the second longest running pistol championship in the world. This year, it will be hosted by the CMP May 20-23, 2025, at the Green Valley Rifle & Pistol Club in Missouri. The Bianchi Cup has been called the most prestigious pistol tournament in the world. Due to the high accuracy required in each stage of the Bianchi Cup, the tournament is considered one of the most difficult handgun championships on the planet.
The Bianchi Cup is Comprised of Four Events:
Practical Event: Competitors fire at distances from 10 yards to 50 yards under varying time limits from the shooting line.
Barricade Event: Competitors fire at targets on either side of the barricade at different distances and under varying time limits from within shooting boxes and behind barricades.
Falling Plate Event: Competitors fire at eight-inch round steel plates arranged in banks of six at distances from 10 to 25 yards under varying time limits.
Moving Target Event: Competitors fire from within shooting boxes at distances ranging from 10 to 25 yards at a target moving from left to right, with the target exposed for six seconds.
Bianchi Cup Open Class Pistol — Features in Review
Above an Australian lady competitor shoots Open Class pistol. Note the large flared grip extension, ported muzzle compensator, and elevated optic. Open pistols may also have special custom fittings: wings for barricades, mover base for leads, and prone pad for stability. Open Class pistols rule at the Bianchi Cup: “Unlike USPSA, all divisions compete heads up at Bianchi. While Bianchi recognizes wins in other divisions, only the absolute top score can win the Cup. Since Bianchi is typically won only with a perfect score, and often by X count, guns other than open are not really competitive.” See Pistol-Training.com.
Position Shooting with Pistols at Bianchi Cup
Competitors shoot from both standing and prone positions and are also required to shoot with both strong and weak hands at various stages. There are no make-up shots in the Bianchi Cup, adding to the difficulty.
Bianchi Cup 1911 Pistol Giveaway
Looking for a 1911 pistol? The Civilian Marksmanship Program (CMP) is giving away a vintage 1911 pistol (plus mags, holster, and ammo) for competitors who register for the upcoming 2025 CMP Bianchi Cup.
The 2025 Bianchi Cup match runs May 20-23 in Hallsville, Missouri. Those who sign up for the CMP Bianchi Cup BEFORE April 27, 2025 will be automatically entered to win.*
To have a chance to win, you must officially register for the 2025 Bianchi Cup. ALL paid registrants will be automatically entered for the raffle. To learn more and REGISTER for the 2023 Bianchi Cup, go to the CMP 2025 Bianchi Cup Web Page.
* The raffle is open to U.S. citizens only. If a non-U.S. citizen is drawn, he or she will receive $500 in place of the 1911 pistol. Those who have already purchased a pistol are still permitted to win.
Team Berger’s Larry Bartholome showcased his shooting prowess by winning the 2025 Western Wildcat Smallbore F-Class Championship. The event, held in March at the Ben Avery Shooting Complex and hosted by the Desert Sharpshooters Rifle Club, brought together the nation’s top smallbore F-Class shooters in a challenging 4-day competition.
Bartholome finished with a 6363 Grand Aggregate score and an impressive 434 Xs, showing remarkable consistency throughout the match. His Western Wildcat win comes on the heels of a strong third-place finish at the NRA Metric Prone National Championship. “The Western Wildcat is one of the most challenging smallbore matches in the country, and I knew I had to bring my absolute best”, said Bartholome. “Thank you to the Lapua group for producing such great .22 ammo. I couldn’t have won without it. The Lapua X-ACT [ammunition] I shot was outstanding.”
Bartholome’s victory at the Western Wildcat highlights not only his personal dedication and skill but also the critical role of precision equipment and top-tier ammunition in elite-level competition. His latest achievement adds to his distinguished career and reinforces his status as one of America’s best F-Class shooters in both centerfire and rimfire disciplines.
Bartholome prepared for the competition by testing ammo lots with his rifle at the Mesa, Arizona, Lapua Rimfire Performance Center. This facility allows testing of of multiple lots at both 50 and 100 meters to identify the best match for a shooter’s rifle. Lapua’s Rimfire Performance Centers, located in Mesa, AZ, and Marengo, OH, provide this ammo-testing service to competitive shooters. Appointments can be scheduled for those looking to refine their ammunition selection.
Want to go to some fun rifle matches in the months ahead? You can access coming events near your location with the interactive NRA SSUSA.org Shooting Sports Coming Events Calendar webpage. You can filter results by shooting discipline (pistol, smallbore rifle, high power rifle etc.) as well as location. You can also view the match locations on a map by clicking on the “View on Map” link on the right side of the page. This alternates with “View as List”.
To see ALL upcoming matches in your area, click on the “Edit Search” button then click the box for the lead category, “All Competition Types”. Or click one or more of these categories:
Action Pistol
Air Rifle
BB Gun
Black Powder Target Rifle
Collegiate Rifle/Pistol
High Power Rifle
International Pistol
Precision Pistol
For example, here are the results of a search for matches within 200 miles of Seattle Washington. First is the list view, then below that is the map view. For any search, you can alternate views by clicking “View on Map” or “View as List” in the right column.
For Summer Travelers, Find Matches Outside Your Home State
If you are planning an out-of-state vacation this summer and you want to combine your travels with a shooting match, simply click the blue “Edit Search” button. Then you can select a different location. Just type in the city and state, or the Zip Code. For example, here are the search results for shooting matches within 75 miles of Las Vegas, Nevada:
Method Two: Apply Wipe-Out from Breech
We doubt if there will ever be real agreement among shooters concerning barrel break-in procedures. And one must remember that the appropriate break-in procedure might be quite different for a factory barrel vs. a custom hand-lapped barrel. This Editor has found that his very best custom barrels shot great right from the start, with no special break-in, other than wet patches at 5, 10, and 15 rounds. That said, I’ve seen some factory barrels that seemed to benefit from more elaborate break-in rituals.
