We had a chance to try out the new power case trimmer head from Little Crow Gunworks. Dubbed the “World’s Finest Trimmer” (WFT) by its inventor, Dale Hegstrom, this device proved fast, precise, and easy to use. When compared to a Hornady Lock ‘N Load hand-crank trimmer, the WFT processed cases twice as fast, and delivered a more uniform cut length with our test brass.
The WFT features a steel shell-holder, aluminum body, and steel drive shank. You can chuck it into any electric drill or power device that can handle the 3/8″ shank. Unlike most case trimming tools, the WFT indexes off the shoulder datum. This permits you to trim cases very quickly, without fiddling around with rim-grabbing collets, or shell-holders. Watch the videos to see the WFT in action.
WFT is Fast and User-Friendly
Mark LaFevers, our tester, was easily able to trim five (5) cases in under 30 seconds. It took quite a bit longer to trim five cases with the Hornady trimmer he used for comparison. Mark noted that, after just a 20 or so manually-trimmed cases, his arm would start to fatigue. By contrast, he could effortlessly trim 100 or more cases with the WFT. For older folks with a bit of arthritis, the WFT makes life easier. Mark observed that the WFT produces a “nice, square, clean cut”, while offering a “very fast cycle rate”. He tells us, “once you get the hang of it, you probably can trim your brass two, if not three times as fast.”
Mark really liked the WFT tool, and a WFT will be replacing his hand trimmer for big jobs. One downside is that, currently, the WFT is cartridge specific — you normally need to have a different tool for each cartridge type you trim. And there are no swappable inserts allowing you to trim different cartridge types with the same tool. However some WFT versions WILL trim different cartridge types within the same “family”, such as .270 Win and .30-06.*
Hi-Rez Video Shows “Trim-Off” Challenge between WFT and Hornady Trimmer
You should definitely watch the five-minute video below. Mark trims five cases with the WFT, and then five more with the Hornady tool. He times the operation of each device and then measures the trimmed cases. The total variation (in length) of the WFT-trimmed cases was .001. With the Hornady tool, there was a much larger spread: .007″ (seven thousandths). Mark cautioned: “Normally the Hornady tool does a bit better than this — the variance won’t be so large. But getting better results (with the Hornady) might require trimming, measuring, then trimming again. In the video I was trying to move pretty quickly and the measurements were all taken after the initial trim. Possibly, if I slowed down when using the Hornady trimmer, the OAL measurements would have been more consistent. But that just further reinforces the point that the WFT is faster.”
NOTE: If you have a fast connection, we suggest you select 720p (HiRez) and expand to full screen.
In the video below, WFT creator Dale Hegstrom demos his device and shows how quickly it can trim a large quantity of brass. Note how the WFT is attached to a common rechargeable power drill.
“World’s Finest Trimmer” Costs $69.95
The Little Crow Gunworks “World’s Finest Trimmer is available for $69.95 from various vendors including Creedmoor Sports. WFTs index off the shoulder, not the base. The case fits tightly into a steel bearing which has been machined to a specific caliber. This decouples the stationary case from the spinning cutting blade and body, giving you a smooth, exact cut each time. While the WFT makes a nice, square cut, we do recommend chamfering inside and outside after the brass is trimmed to length.
*Most WFTs are cartridge specific. Available sizes include: .204 Ruger, .223 Rem, 22-250, 6mmBR, 6.5 Grendel, 6.5×47 Lapua, 6.5 Creedmoor, 6.5-284 (and 6mm-284), 6.8 SPC, 270 WSM, 7mm Rem Mag (and 300 Win Mag), .308 Win, 300 WSM, .338 Lapua Magnum. There is a ‘5 in 1′ WFT unit that will handle .17 Rem, .221 Fireball, .222, .223 Rem, and .222 Mag. The 6mmRem unit also works with .257 Roberts and 7×57 Mauser. The .30-06 WFT will trim .270 Win, .280 Rem, and .25-06 as well. And the WFT for Ultramags works with 7mm, 300, and .338 Ultramags.
Share the post "Gear Review: ‘World’s Finest Trimmer’ from Little Crow Gunworks"
We are organizing our crew for the 2013 SHOT Show, which runs January 15-18 in Las Vegas, at the Sands Expo Center. To whet your appetite, here is a product report from SHOT Show 2010 that you may have missed the first time around. In this video Robert Ruch, CFO of Forster Products, shows off the Forster’s 3-in-1 Case Trimming Tool. This is a very smart tool that can dramatically speed up your case prep operations.
Tool Cuts Brass to Length, and Chamfers Inside and Outside
Forster’s new 3-in-1 Carbide cutting tool works with all existing Forster case trimmers. This unit does three jobs at the same time. It trims the case to length, it puts a 14-degree chamfer on the INSIDE of the neck, AND (last but not least), it cuts a 30-degree chamfer on the OUTSIDE of the neck. It does this all quickly and efficiently — in a matter of a few seconds. We tested the new tool ourselves on a few cases. The tool is solid and well made. The carbide cutting tips do perform a very clean cut. Be aware, however, if you have turned your necks already, you may have to reset the blade positions before you start trimming your brass.
Forster’s CFO, Robert Ruch, demonstrates the 3-in-1 case trimming/chamfering tool in the video below. As you can see, the tool turns very smoothly (no chatter) and the job is finished in a few seconds. The actual cutting time, per case, is just a few second. The tool has an MSRP of $70.00, but we expect it to sell for around $50.00 at major vendors. It can be fitted on Forster trimmers and other hand lathes with a .490″ shaft diameter.
John Whidden Demonstrates Forster Co-Ax Press and Trimmer
In this promo video, produced for the Outdoor Adventure ‘What-the-Stuff’ TV show, John Whidden of Whidden Gunsworks, talks about the benefits of precision case trimming and demonstrates how to use the unique Forster Co-Ax Press.
Share the post "Forster 3-in-1 Case Trimming Tool"
Now through April 6, 2012, Sinclair’s Stainless Micrometer “Ultimate Trimmer” system is on sale for $159.99. That’s a $20.00 savings off the normal $179.00 price. This unit comes complete with micrometer cut-length control, stand, Shark Fin clamp for the case-holder, and a stainless Wilson cutter housing. NOTE: Caliber-specific case-holders are sold separately.
The Sinclair Micrometer head allows reloaders to easily adjust trim length in .001″ increments with an adjustment length of over 2″. The micrometer features easy-to-read, engraved unit markings and may be locked in place. The Ultimate Trimmer can trim cases from 22 Hornet up to 416 Rigby.
The Sinclair Stainless Ultimate Trimmer comes with Sinclair Mounting Stand and handy Shark Fin Clamp. This system makes easy work of installing and removing your trimmer case holder in a smooth “swing-arm” motion. The Shark Fin trimmer clamp secures the case head firmly against the micrometer adjustment head for a quick and accurate, chatter-free trim. NOTE: We have found that you will get the most accurate, repeatable trim lengths if you set the shark fin to a firm tension and do NOT hold the case-holder with your hand — let the Shark Fin clamp do the job. The video below shows how to use a Wilson case trimmer (with micrometer, stand and Shark Fin).
Share the post "Save $20.00 on Sinclair Stainless Ultimate Case Trimmer"
The May digital edition of Shooting Sports USA has a good article on Power Case Trimmers for rifle brass. Trey Tuggle reviews self-powered units from Giraud, Gracey, Hornady, and RCBS, plus a drill-mounted trimmer fitting from Little Crow Gunworks. Tuggle reviews the main features of each unit. Reading this article is recommended for any one in the market for a high-output, powered case prep machine. CLICK HERE to read story.
State Champions Listed by Discipline
The May edition of Shooting Sports USA also dedicates six full pages to 2010’s State Champion shooters, listed discipline by discipline. The recognition give these many shooters is well-deserved. As you’ll find in every edition of Shooting Sports USA, there is a comprehensive calendar of NRA shooting competitions for a vast range of disciplines: Action Pistol, Air Pistol, Pistol Silhouette, Black Powder Target Rifle, Black Powder Silhouette, Lever Rifle Silhouette, Air Rifle, Smallbore Rifle, Smallbore Rifle Silhouette, High Power Rifle, High Power Silhouette, and more. You’ll find match listings for hundreds of shooting clubs around the country.
Share the post "Power Case Trimmers Reviewed in May Shooting Sports USA"
“World’s Finest Trimmer” Costs $69.95
The Sinclair Stainless Ultimate Trimmer comes with Sinclair Mounting Stand and handy Shark Fin Clamp. This system makes easy work of installing and removing your trimmer case holder in a smooth “swing-arm” motion. The Shark Fin trimmer clamp secures the case head firmly against the micrometer adjustment head for a quick and accurate, chatter-free trim. NOTE: We have found that you will get the most accurate, repeatable trim lengths if you set the shark fin to a firm tension and do NOT hold the case-holder with your hand — let the Shark Fin clamp do the job. The video below shows how to use a Wilson case trimmer (with micrometer, stand and Shark Fin).
State Champions Listed by Discipline
