For years we have touted the advantages of Burris Signature rings, with polymer Pos-Align Inserts. PRS/NRL shooters take note — this technology is available in a beefier, heavy-duty ring system for tactical rifles. The impressive Burris XTR Signature Rings offer six (6) clamping bolts per ring plus strong, dual steel base-clamps that self-center on Weaver or Picatinny rails. These aluminum XTR Signature Rings provide strength and holding power, plus the key benefits of Pos-Align inserts. As impressive as XTR rings are — they aren’t that expensive, with 1″-diameter XTRs starting at about $90.00 per pair (30mm and 34mm XTRs cost a bit more).
The polymer inserts in Signature rings perform three key functions. First, the inserts provide full, uniform scope-to-ring contact, with no need for lapping. You get a very secure “grip” on your scope without ring marks. Second, the Pos-Align inserts can provide elevation “pre-load”. With eccentric (offset) inserts, you can raise the back of the scope relative to the front, gaining up to 54 MOA of built-in elevation, without the need for expensive tapered bases. Third, the offset inserts can be rotated clockwise or counter-clockwise to shift point of impact. This lets you zero your rifle easily while keeping the turrets in the center of their travel.
Burris XTR Signature Rings are offered in 1″, 30mm, and 34mm diameters, and three (3) different heights: 1″, 1.25″, and 1.5″. Each ring set includes two sets of concentric inserts and one set each of the following offset inserts: +/-5 MOA, +/-10 MOA, +/-20 MOA. These allow you to “pre-load” elevation and/or center up your cross-hairs.
– Pre-load Elevation. No need for expensive tapered bases for long-range shooting.
– Correct misalignment caused by off-center receiver holes.
– Correct for bases or rings being slightly off-center.
How to Pre-load Elevation
To add elevation, set the Pos-Align Offset Inserts to raise the rear of the scope and lower the front. As long as there remains sufficient clearance between the front objective bell and the barrel, Burris recommends lowering the front of the scope the most and raising the rear of the scope the least. The amount of actual elevation “pre-load” will depend on the ring spacing (see chart). In the illustration, with 4.75 inches between ring centers, a +/- 20 MOA pair in the front combined with a -/+ 5 MOA pair in the rear will yield +25 MOA of total elevation. (If the rings are positioned further apart, you’ll get less elevation pre-load.)
Using Inserts to Adjust Point of Impact in Any Direction
Although it is convenient and most understandable to refer to the ring inserts as a “bottom” or “top” insert, the inserts may be rotated to any angle within the scope rings. This allows the shooter to correct the point-of-impact in any direction. The drawings below show how the inserts can be rotated to induce both elevation and windage changes at the same time.
Product tip from Boyd Allen. We welcome reader submissions.
This week, Shooting USA TV spotlights the 2022 GAP Grind, the largest PRS Pro-Am Tactical match with nearly 400 competitors. The 10th Annual GA Precision/Elite Tactical GAP Grind PRO-AM was held September 30 through October 2, 2022 at the K&M Shooting Complex in Tennessee. The GAP Grind, the largest, most popular PRS match in the world, drew nearly 400 amateur and pro shooters. Recognized as the premier PRO-AM precision rifle match with both individual and team competition, the GAP Grind has introduced thousands of new shooters to the sport since its inception. It was great to see the GAP Grind successfully mark its 10th Anniversary.
SHOW TIMES: This Shooting USA Episode airs Wednesday, April 12, 2023 at 9:00 PM Eastern and Pacific; 8:00 PM Central. If you miss the regular broadcast, you can stream the show at any time on Vimeo for $0.99 per episode.
In this video Eagle Eye Shooting Shares Highlights from the 2022 GAP Grind
Big Prize Table at 10th Annual GAP Grind Event
The year’s largest PRS match drew hundreds of attendees, and more than 80,000 rounds were fired throughout the three-day event. Bushnell gave out $5,000 to the top place finishers and added over $5,000 worth of product to the prize table. Trophies were awarded to the top 5 teams, top 5 professionals, and to the top 5 amateurs.
Lots of Action, with 20+ Stages
The GAP Grind is a challenging, “high tempo” match with minimal down-time between stages. Over the course of 20+ stages, competitors will fire 200+ shots at a variety of steel, paper, moving, and reactive targets out to 1,200 yards. Targets vary in size/difficulty based on the shooter’s position, distance, and time allotted. Most stages include “stressors” — i.e. time limits or required movement(s).
This extensive, 45-minute video shows many of the 2022 GAP Grind Stages
GAP Grind Pro-Am Format — Seasoned Shooters Help Newcomers
The GAP Grind typically attracts nearly 400 competitors — half experienced shooters and the other half newcomers to the sport. The key to growing the shooting sports is attracting new shooters. The best way to bring in “new blood” seems to be the Pro-Am type format. At the GAP Grind, experienced shooters share their knowledge and guide the new shooters through the competition.
GAP Grind Hardware
You’ll find the latest and greatest PRS hardware at the GAP Grind. Over the past few seasons, most top competitors have “stepped down” from the 6.5/6mm Creedmoor to the smaller, more efficient 6mm Dasher, 6BRA, 6 GT and other 6mm cartridges. The Dasher offers excellent accuracy with less recoil than the 6.5 Creedmoor. Also, many competitors will be switching to the impressive new Zeiss FFP LRP S3 and S5 scopes in the months ahead.
The new Tunable Ultimate Recoil Device from MDT allows you to shoot smaller calibers with nearly 3.14 times more recoil. This is a big deal for tactical competitors who want to cross-train with rimfire rifles that use much more affordable .22 LR ammo. (Good .22 LR ammo can be purchased for under $0.15/round.)
With this new MDT reverse-pulse muzzle brake, a .22 LR rig will feel like a .223 Rem, and a .223 Rem can feel like a .308 Win. The added recoil provides realistic training, stressing perfect body position while allowing you to save money on ammo.
Watch Video to See Tunable Ultimate Recoil Device in Action
With very large calibers (.338 and above), the MDT-TURD can increase felt recoil up to 900%. This heavier recoil pulse can help a shooter build muscle strength during training.
Built with marine-grade submarine steel and reverse baffles, the MDT-TURD creates parabolic concussion forward and to the side. The unique patent-pending design removes the need for hearing protection for the shooter while creating disorientation for competitors at your match.
The above image shows a .22 LR tactical rifle on recoil-measuring slide platform. (See Video at 1:15 time-mark). With the MDT-TURD fitted, the rimfire rifle shows significantly greater recoil — 314% more compared to the same rig with bare muzzle. This allows more effective cross-training, as the device-equipped rimfire rifle will have a recoil pulse more similar to a centerfire PRS/NRL rig.
This image show how the forward-angle brake ports INCREASE the felt recoil by venting the explosive energy FORWARD. This effectively pushes the rifle backward, increasing felt recoil. This way a .223 Rem can recoil like a .308 Win, and a .22 LR rimfire rifle can recoil like a .223 Rem.
About MDT ▬▬▬▬▬▬▬▬▬▬▬▬
MDT was born with a single purpose — to provide better value and better accuracy for precision rifles. The first MDT chassis was developed from the ground up based on the needs of shooters. Our engineers verified every function and feature based on the input from competitive shooters. The end result was a game-changing product called the TAC21 that continues to perform at the range, in the field and in competitions around the world.
Today, MDT chassis systems, magazines, and accessories are still developed the same way. We collaborate, question and verify our concepts with precision shooters from around the globe to ensure that every MDT product is designed with the same single purpose — to provide our customers with the absolute best product possible.
The National Rifle League (NRL) started off sponsoring major centerfire tactical matches, similar to PRS competitions. That proved successful so the NRL added a .22 LR Rimfire series, called NRL22. The NRL22 rimfire discipline has been a major success, as rimfire guns are fun to shoot and ammo is very affordable. The most popular NRL22 matches have drawn up to 200 rimfire competitors. And now there is a companion rimfire long-range series, NRL22X. Learn more about NRL22 and NRL22X at NRL22.com.
NRL22 is a great way to get into competition shooting with minimal expense. There are six (6) classes: Open, Base, Ladies, Young Guns (8-16), Old Guns (OG 60+), and Air Rifle. Base Class is for the budget-minded shooter — the combined MSRP of Rifle and Optic may not exceed $1650.00 in 2026 (so you could spend $950 on a rifle and $700 on a scope for example). That keeps the sport affordable.
Open, Youth, OG, and Ladies Classes have no price limits on rifle and optic. Visit NRL22.com to find an NRL22 match near you. CLICK HERE for a full set of NRL22/NRL22X rules. The NRL also sponsors NRL22X matches. These involve significantly longer distances for greater challenge. Currently, an NRL22 membership costs $60/year for adult classes or $25/year for Young Guns Class.
March 2023 NRL22 Course of Fire
For actual NRL22 competitors, this is a very useful video. It shows how shooting from a variety of positions, and it includes very cool through-the-lens views. This covers the NRL22 March 2023 course of fire.
NRL22 Competition with Base Class ($1200 Max) Rifle
One good thing about NRL22 competition is you don’t need to spend a fortune to compete. Base class is limited to $1200.00 for rifle and optic. You can do very well even at this budget level. This video, complete with through-the-lens imagery, shows an NRL22 match shot with a Base Class Ruger Precision Rimfire rifle.
NRL22 and NRL22X are not just for guys. The ladies enjoy the competition too and do very well. There is a separate Ladies class, but women can also compete in other classes. Photo by Jonathan Ocab.
Interview with NRL22 Founder Travis Ishida
This Vortex Nation video features an 80-minute interview with Travis Ishida, one of the original founders of the NRL22 and NRL22X disciplines. Travis told us that the NRL now runs 7-8 times as many rimfire matches as centerfire matches.
NRL22 Competition Guide — Match Procedures and Equipment
If you want a basic overview about NRL 22 Competition, there is a good NRL22 Competition Guide on the Widener’s website. This covers the classes, the rules, target dimensions, the types of supports used, and match strategies. Here are some samples:
Any rifle system that comes in under a combined MSRP of $1200 shall be eligible to compete in the Base class. This combined MSRP price is for the rifle and scope only. It excludes scope rings and bases, bipods, suppressors, data cardholders, magazines, spare magazine holders, auto bolt releases, aftermarket triggers, and extended magazine releases. Adjustments are also allowed in this division as well as adding rails of any type. If any shooter goes over the MSRP amount of $1200, they get bumped into Open class.
One of the most obvious rules is that all rifles must be chambered in .22 Long Rifle. Magnum and like rimfire cartridges are not allowed. It is recommended that whatever rifle you choose has a removable magazine rather than a fixed, tubular magazine since it’s harder to make safe, but they are allowed.
You can use any equipment in NRL22 unless a specific course of fire rules out using an item specifically. The only exception is tripods are never allowed. The sharing of equipment is allowed as well as slings to assist in unsupported positional shooting.
The steel target dimensions range from .25 inches wide to 6 inches wide. Some stages will require 10 rounds to be shot, while others may have you shoot 12 rounds. Most often, you’ll have 120 seconds to shoot a course of fire.
Ammunition Selection for NRL22 and NRL22X
Our friend F-Class John, a top F-Open competitor, has recently started tactical rimfire matches. He enjoys the challenge. And he admits a big part of the appeal is the MUCH cheaper ammunition. He has seen good results with relatively inexpensive Norma Tac-22 ammo, but he now favors SK ammo which he says offers great performance for the price. In this video, F-Class John tests SK Rifle Match Ammo vs. the premium Lapua Center-X ammo. He tested using a benchrest set-up with his MPA chassis rimfire rifle.
How to Register for NRL22 Competitions
Looking to get started in NRL22 or NRL22X (long range) competition? CLICK HERE to visit the NRL22 home page. The NRL22/NRL22X website has a registration page along with information on equipment rules, match locations, match rules, and the 2023 Match Schedule. CLICK HERE for NRL22 rules and CLICK HERE for NRL22X-specific Rules.
BONUS — Rimfire Practice Targets
SPECIAL BONUS–Rimfire Tactical Precision Targets
These FREE targets by DesertFrog are offered in Adobe Acrobat format for easy printing. CLICK HERE to download all six targets as a .ZIP archive.
This article Copyright 2025 AccurateShooter.com. Any reproduction without authorization gives rise to penalties under 17 U.S. Code § 501.
Many guys getting started in long range shooting are confused about what kind of scope they should buy — specifically whether it should have MIL-based clicks or MOA-based clicks. Before you can make that decision, you need to understand the terminology. This article, with a video by Bryan Litz, explains MILS and MOA so you can choose the right type of scope for your intended application.
You probably know that MOA stands for “Minute of Angle” (or more precisely “minute of arc”), but could you define the terms “Milrad” or “MIL”? In a helpful video, Bryan Litz of Applied Ballitics explains MOA and MILs (short for “milliradians”). Bryan defines those terms and explains how they are used. One MOA is an angular measurement (1/60th of one degree) that subtends 1.047″ at 100 yards. One MIL (i.e. one milliradian) subtends 1/10th meter at 100 meters; that means that 0.1 Mil is one centimeter (1 cm) at 100 meters. Is one angular measurement system better than another? Not necessarily… Bryan explains that Mildot scopes may be handy for ranging, but scopes with MOA-based clicks work just fine for precision work at known distances. Also because one MOA is almost exactly one inch at 100 yards, the MOA system is convenient for expressing a rifle’s accuracy. By common parlance, a “half-MOA” rifle can shoot groups that are 1/2-inch (or smaller) at 100 yards.
What is a “Minute” of Angle?
When talking about angular degrees, a “minute” is simply 1/60th. So a “Minute of Angle” is simply 1/60th of one degree of a central angle, measured either up and down (for elevation) or side to side (for windage). At 100 yards, 1 MOA equals 1.047″ on the target. This is often rounded to one inch for simplicity. Say, for example, you click up 1 MOA (four clicks on a 1/4-MOA scope). That is roughly 1 inch at 100 yards, or roughly 4 inches at 400 yards, since the target area measured by an MOA subtension increases with the distance.
MIL vs. MOA for Target Ranging
MIL or MOA — which angular measuring system is better for target ranging (and hold-offs)? In a recent article on his PrecisionRifleBlog.com website, Cal Zant tackles that question. Analyzing the pros and cons of each, Zant concludes that both systems work well, provided you have compatible click values on your scope. Zant does note that a 1/4 MOA division is “slightly more precise” than 1/10th mil, but that’s really not a big deal: “Technically, 1/4 MOA clicks provide a little finer adjustments than 1/10 MIL. This difference is very slight… it only equates to 0.1″ difference in adjustments at 100 yards or 1″ at 1,000 yards[.]” Zant adds that, in practical terms, both 1/4-MOA clicks and 1/10th-MIL clicks work well in the field: “Most shooters agree that 1/4 MOA or 1/10 MIL are both right around that sweet spot.”
Doug Koenig is one of the best action shooters in history — both with rifle and pistol. In a recent video from SHOT Show Range Day, Doug, a 19-time Bianchi Cup Champion and a PRS Production Division Champion, talks about the disciplines he shoots, both rifle and pistol. He notes he has moved to Florida and he will be starting his own shooting school, which will open at the end of the year.
In this video, Doug is interviewed by Shooting Sports USA Editor John Parker. Koenig talks about his namesake Precision Rifle Series competition held in Colorado, the revitalized U.S. Steel Nationals and more.
You can see more Doug Koenig PRS/NRL videos on the Pursuit Channel, including coverage of precision rifle matches in Pennsylvania, Colorado, and Wyoming. The videos are worth watching for the scenery as well as the rifle action.
Doug Koenig — Action Pistol Master
Doug Koenig has won the Bianchi Cup a remarkable 19 times. No one else, man or woman, is even close to that achievement. After his Bianchi victory in 2021, Doug said: “Winning the Bianchi Cup title for the 19th time in my career is very special on its own. But to do so after the difficult year we’ve all faced, and to do so wearing a Team Ruger jersey, has made this win that much more meaningful for me.”
What skills does it take to win a Bianchi Cup? You need speed, accuracy, control, and discipline. Koenig explains some of these techniques in the video below. You’ll find 30 more Doug Koenig videos on the NSSF YouTube Channel:
The ZEISS LRP S5 525-56 rifle scope has won a prestigious honor from Outdoor Life magazine. This advanced 5-25x56mm First Focal Plane (FFP) optic was named “Best Overall” in the article entitled The Best Long Range Rifle Scopes of 2023. This ZEISS scope won overall top honors for its exceptionally good lenses and its best-in-class elevation adjustment. Outdoor Life’s award article summarized: “Why It Made The Cut: Built around premium glass and a reticle designed for Precision Rifle Series steel-target competitions, the [ZEISS LRP S5 525-56] has the best turrets and most adjustment range in the class.”
The review continued: “The LRP S5 … easily won the top award in this year’s Outdoor Life optics test, taking top spots in both the resolution and low-light portions of the test. But what wowed testers were the features built for both dialing and holding for distant targets.
The illuminated ZF reticle is available in either MOA or MRAD versions. The MRAD version incorporates a tree-style structure with abundant elevation and windage references without seeming cluttered. The MOA version is more of a hash-style, with references on the main stadia. Both are fast, precise, and simple. In keeping with those superlatives, the [ZEISS LRP S5] scope has a crazy amount of internal adjustment in the 34mm tube, 40.7 MRAD (140 MOA) of elevation travel and 24 MRAD (60 MOA) of windage adjustment. That means you can engage targets from inside 100 yards out to 1,500 yards simply by holding on the reticle’s center aiming point and dialing your aiming solution.”
Advanced Optical Technology — ZEISS LRP S5 Features
The ZEISS LRP S5 525-56 has many notable features, including a lockable windage turret, adjustable reticle illumination, and a HUGE amount of elevation travel — 40.7 Mils in the MIL model and 140 MOA in the MOA version. That gives this optic the ability to shoot at extreme range without requiring holdovers.
Every year the NRA Publications group announces Golden Bullseye Award winners for various product categories (rifle, handgun, shotgun, optics, gear etc.). These awards are like the Oscars for the shooting industry. There are many Golden Bullseyes given out each year because there are separate awards given by different NRA Magazines — including American Rifleman, Shooting Illustrated, and American Hunter. Here are the 2023 Rifles of the Year (Golden Bullseye Winners) as chosen by each of those three publications.
American Rifleman 2023 Golden Bullseye Award Winner
Rifle of the Year — Marlin 1895 SBL by Ruger
In late 2020, Ruger acquired the assets of the Marlin Firearms, as part of the Remington bankruptcy sale. After acquiring the Marlin assets from Remington, Ruger put its engineers to work producing one of the best-machined Marlins ever, the impressive Marlin 1895 SBL. The first new-generation model 1895 SBL rifles were chambered for the .45-70 Gov’t cartridge.
Ruger President/CEO, Chris Killoy explained how the Model 1895 SBL was developed: “Since the move of over 100 truckloads of equipment and inventory back in November 2020, our engineering team took the 1895 through a complete design and production review, focused on achieving the highest quality, accuracy, and performance standards. The end result is a quality rifle, produced using modern manufacturing methods[.] From the quality of the firearm, to clear ways for consumers to differentiate Ruger-made Marlins, we focused on getting every detail right.”
Ruger-made Marlin 1985 SBL rifles bear an “RM” (Ruger-Made) serial number prefix, have the Marlin Horse/Rider logo laser-engraved on the grip, and include a red and white bullseye on the buttstock.
American Hunter 2023 Golden Bullseye Award Winner
Rifle of the Year — Nosler Model 21
The new Nosler Model 21 rifle has many advanced features. Along with a lightweight McMillan carbon fiber stock, the Model 21 boasts a wire EDM-machined receiver, nitride-coated fluted bolt, and TriggerTech trigger. Excellent accuracy is delivered with a Shilen match-grade stainless barrel, threaded at the muzzle for brake or suppressor. The Model 21 is offered in a wide variety of chamberings from .22 to .375 calibers: 22 Nosler, 26 Nosler, 6.5 Creedmoor, 6.5 PRC, 27 Nosler, 280 Ackley Improved, 28 Nosler, .308 Win, .300 Win Mag, 30 Nosler, 33 Nosler, and .375 H&H Magnum.
The heart of the rifle is Nosler’s new Model 21 action, designed in collaboration with the Mack Brothers from South Dakota, creators of the advanced EVO action popular with precision shooters. Nosler’s newly-designed Model 21 blends the best features of the EVO action with unique Nosler-engineered customizations, delivering an ultra-reliable, smooth cycling action, well suited for hunting applications.
Nosler Model 21 with McMillan Carbon Fiber Stock
Shooting Illustrated 2023 Golden Bullseye Award Winner
Rifle of the Year — Springfield Armory Saint Edge ATC
Springfield Armory’s new SAINT Edge ATC is built around a patented “Accurized Tactical Chassis”, an advanced evolution of the AR platform. Featuring a monolithic lower/handguard system, the SAINT Edge ATC delivers a 100% free-floated barrel. This ensures that the barrel, barrel nut and gas system are totally free from any contact with the lower chassis.
Chambered in .223 Wylde, the SAINT Edge ATC is offered in a standard black model as well as an Elite version finished in Cerakote® Coyote Brown, paired with an upgraded LaRue 2-Stage trigger and B5 Systems’ Precision Stock. For those that demand sub-moa precision from their AR-style rifle, the SAINT Edge ATC series is guaranteed to deliver.
About the Golden Bullseye Awards
Now in their 21st year, the NRA Publications Golden Bullseye Awards acknowledge top products available in the shooting sports. The winners are selected by a committee of editors, graphic designers, and NRA Publications staffers, representing more than a century of collective experience in the shooting/hunting industry. This year’s Golden Bullseye Awards are noteworthy as American Rifleman magazine is celebrating its 100th anniversary, while American Hunter magazine marks its 50th year of publication. Golden Bullseyes are also awarded by the NRA’s Shooting Illustrated magazine, and NRAWomen.com website.
To qualify for consideration for a Golden Bullseye Award, a product must have been:
— Recently introduced and available to consumers.
— Used/tested by a staff member or magazine contributor.
— Reliable in the field, meeting or exceeding the evaluator’s expectations
— Innovative in design and function.
— Readily perceived as a value to the purchaser.
— Styled in a manner befitting the shooting and hunting industry.
NRA Publications Executive Director Doug Hamlin stated: “The NRA Golden Bullseye Awards epitomize what NRA members seek in their shooting and hunting equipment—outstanding performance, innovation and value. These are the best new products, truly worthy of NRA Members’ attention, and I extend my heartfelt congratulations to all this year’s winners.”
Precision Rifle Series (PRS) 22 Finale on Shooting USA
This week Shooting USA showcases the first-ever PRS Rimfire Finale. This new rimfire discipline is akin to Precision Rifle Series (PRS) centerfire tactical competition, but shot with .22 LR rimfire rifles. The inaugural PRS Rimfire Finale drew nearly 150 competitors to Texas, where shooters could compete without the cost of expensive centerfire ammo and without the need for a 1000-yard range. SEE: PRS Rimfire Series Info.
Shooting USA SHOW TIMES: This Shooting USA Episode airs Wednesday, December 21, 2022 at 9:00 PM Eastern and Pacific; 8:00 PM Central. If you miss the regular broadcast, you can stream the show online at any time on Vimeo for $0.99 per episode.
PRS Rimfire Finale — Nearly 150 Shooters in Texas
PRS and NRL tactical matches are among the fastest-growing competitive shooting disciplines. And rimfire tactical disciplines are actually growing even faster (than centerfire PRS/NRL) because .22 LR ammo is much cheaper than centerfire ammo, and there are many more ranges where rimfire matches can be held. PRS Rimfire offers the same kind of fun without the high cost of centerfire ammo and/or countless hours spent hand-loading. Rimfire PRS also offers generally less expensive rifles, and a whole lot less recoil. That’s why PRS Rimfire (as well as NRL22) has become so popular. And in the first year of the PRS Rimfire series, the Finale drew close to 150 competitors. The Finale Match was held at the Triple C Shooting Facility in College Station, Texas.
The Triple C Shooting Facility hosted the First Annual PRS Rimfire Finale. At this excellent Texas venue, match directors set out 20 unique courses of fire. There were the standard props you’d expect to see at any Precision Rifle match — tractor tires, wire spools, concrete culverts, and even cross tie bunkers. And the target placements were certainly challenging. Many of the stages had cross-course target lay-outs. This makes wind-reading much more challenging, especially with the relatively slow, low-BC .22 LR cartridges used in PRS rimfire competition.
Tune in to Shooting USA TV on Wednesday 12/21/22. You’ll enjoy the coverage of this popular PRS rimfire sport that is growing rapidly. Notably, the National Rifle League (NRL) now conducts many more NRL22 matches than NRL centerfire matches. And competitors of course are drawn by the fun/challenge of a tactical match with much lower ammo costs — $0.15-$0.25/rd vs. $1.00/rd or more (counting brass, primer, bullets, powder, and barrel wear). And there are many more viable venues, because you only need a 300-yard (max) range to conduct a rimfire tactical match.
Congratulations to Lapua’s Chris Simmons, who won the 2022 Precision Rifle Series (PRS) Rimfire season with a total score of 689.803.
Simmons was crowned the 2022 Champion this past weekend at the PRS Rimfire Finale hosted by the TX Precision Matches in Navasota, Texas. Competing with Lapua Center-X .22 LR ammunition, Simmons had three podium finishes in the series this year. He took first place at the July-Alabama Precision Rimfire Challenge, first at the Caroline Shooters Group PRS rimfire Series, and second place at the Atlantic Coast Regional Rimfire Finale. In addition to his recent PRS overall rimfire championship, Simmons won the NRLX22 Rimfire National Championship title for the second consecutive year. Having won BOTH both the PRS Rimfire title AND the NRLX22 crown in the same year, Chris is arguably the world’s most successful rimfire tactical competitor.
“The PRS Rimfire Series is a year-long marathon of single matches that comes down to two days of shooting against the best shooters in the country,” commented Simmons. “Consistency wins championships and using Lapua products helps me achieve success with consistency.”
Simmons’ Lapua Center-X .22 LR ammunition is matched to his firearms at Lapua’s Rimfire Performance Center. Specific lots of ammunition are tested at 50 and 100 meters simultaneously, identifying the best performing ammunition in a particular rifle. This service is available to any shooter who wishes to gain a competitive advantage. You can schedule testing at Lapua’s Rimfire Performance Centers. There are two testing facilities — one in Mesa, Arizona, and the other in Marengo, Ohio.
About Lapua
Lapua produces high-quality rimfire and centerfire cartridges and components for civilian and professional use. Lapua is a part of the Capstone Precision Group, exclusive U.S. distributor for Berger, Lapua, Vihtavuori and SK-Rimfire products. For more information, visit Lapua.com.
Every year the 
