21st Century Shooting produces a high quality powder funnel, that is very “user-friendly”. The top section is precision ground and polished for a smooth flow. The center has a see-through tube so you can watch the progress of your powder dropping into the case. At the bottom of each funnel is a black case adapter that seats securely yet won’t get stuck on the case. There are five different adapter sizes — the smallest fits .17 Rem to .223 Rem, while the largest fits big magnum calibers. We use the mid-sized, #3 adapter most often. This fits 6mmBR, 6.5×47 Lapua, and .308 Win family of cases (.243 Win, .260 Rem, 7mm-08, .308 Win). Additional adapters are $6.99 each. There are three tube lengths available: 3″, 6″, and 10″. So, if you need an extra-long drop tube (to help fill PPC and other small cases), 21st Century has you covered.
The funnels are priced by size. The 3″-long model is $24.00, the 6″-long model is $27.00, and the big 10″-long model is $31.00. Prices include one (1) adapter. These high-grade funnels will help you load faster and easier, with fewer spilled kernels. We use these funnels and they do work well. The appropriate collars fit your .223 Rem, 6PPC, 6mmBR, Dasher, 6XC, .260 Rem, .284 Win, and .308 case necks just right — not too loose, not too tight. Kernels flow smoothly through the tube without sticking to the sides. The aluminum top section does not seem to attract a static charge so you don’t have to waste time brushing kernels off the funnel after use. We like this product. For high-volume precision reloaders, these funnels are worth the money.
Want smoother chamfers on your case-mouths? Here’s a simple tip that can: 1) remove the sharp edge left by chamfering blades; and, 2) create a smoother entry for your bullets. Smoothing the inside chamfer can avoid nicks on your bullet jackets, and can also make bullet seating more consistent.
If you are using a 45° rocket tool on newly-trimmed brass, start your inside chamfer with two or three turns in the normal cutting direction. Keep the tool centered, and use light-to-moderate pressure — you don’t need to remove a lot of brass. After your cutting turns (which should reveal a shiny chamfer line), take out the tool, inspect the neck and remove any small brass chips or shavings.
Now here’s the secret — put your tool back in the neck and go in the reverse direction for a couple partial turns. Again, be sure to keep the tool centered and use a light touch. The reverse rotation of the rocket tool inside the case mouth will burnish and smooth the chamfer. Next you can make a quick spin with some fine steel wool held in your fingers. Don’t grind away — you do NOT want to get rid of all the carbon in the neck. As a last step we run a hand-held nylon brush in the neck for 2-3 quick passes to further smooth out the chamfer and remove any residue from the steel wool.
We think, if you use this procedure, your will find that your bullets seat more smoothly and consistently. That can improve accuracy and help avoid mysterious fliers.
You can use this same technique even if you prefer a sharper angle chamfer tool for your initial inside-neck chamfering operation. Reverse your tool gently a couple turns to burnish and smooth the cut. And always remove brass chips and shavings before you run the tool backwards (in the non-cutting direction).
Don’t Forget to Smooth the Outside Chamfer Too
You can also use the backwards rotation trick on outside chamfers to smooth and soften the sharp edge. A little steel wool, applied judiciously, can help here. If you are chamfering a large number of cases after trimming, you may want to tumble the brass in corn-cob or walnut media after the chamfering procedure. Tumbling further smooths the chamfer. You want a nice, smooth chamfer with no burrs or sharp edges.
How would you like to lower your Extreme Spread (ES) and Standard Deviation (SD) significantly by a simple procedure that takes seconds and costs almost nothing?
Here’s all you need to do. After lubing your cases for full-length sizing, be sure to clean your hands (removing ALL residual lube) before you handle your bullets. As an extra measure to avoid lube contamination, slip on thin Latex gloves before you handle and seat your bullets. Will this make a difference? Let me tell you a story.
Keep Those Greasy Fingers Off Your Bullets
I recently loaded a couple dozen cases for a 6mm Dasher. We were in a hurry to leave for the range so I was loading faster than normal. When we started shooting the ammo I noticed that the 5-shot ES was bad — really bad — 48 fps. I was shocked because this was a known good load that had previously showed ES in the teens. This one had me stumped. What could have resulted in this high ES? What did I do different while reloading this time?
Then a lightbulb went off. I realized I had been seating bullets (round by round) immediately after lubing and sizing each case. My fingers still had some greasy lube on them which obviously got on some of the bullets, “polluting” them. My normal reloading procedure is to lube and size all cases, clean them off, then place the brass in a loading tray. Then I would clean my hands BEFORE adding powder and seating bullets. This time, in my rush, I sized a case, wiped it off, then immediately added powder and projectile. I did not take the time to clean off my fingers carefully before handling the bullets.
Big Drop in ES When I Avoided Bullet Contamination with Case Lube
The next day I went back to the loading room. I loaded the same brass with the same powder, same primer, same bullet type, same bushing — same everything. But this time, I washed my hands thoroughly with a hand cleaner, dried them with a clean paper towel, and I even put on thin latex gloves before handling the bullets. I loaded 10 rounds and fired them over the chronograph again in the same rifle. The 5-shot ES was 14 fps and the 10-shot ES was 22 fps (That’s normal for this load/rifle). Compare that to a 5-shot ES of 48 the day before. I had reduced my 5-shot ES by 70%! We were back in business. (By the way, the groups were also very small).
Lesson Learned — Keep Case Lube Off Your Bullets Your results may vary of course, but now I always make sure to remove ALL residual lube from my fingers before handling bullets or doing anything that can get unwanted lube inside the necks.
What about gloves? I don’t think the Latex gloves are essential (if your hands are dry and clean), but they just cost a few pennies when bought in bulk. You can buy a box of 100 latex gloves for under $7.00 on Amazon.com. I suggest the non-powdered type.
Use Your Common Sense
Before the critics launch a tirade, let me be the first to acknowledge that many champions have loaded perfectly good ammo (and shot great groups) without paying much attention to greasy fingers. We’ve all seen short-range benchresters loading ammo between relays. They work fast and may not take the time to clean all lube off their fingers before seating bullets. And we’ve seen some of those guys go out and shoot itty-bitty groups in the ones and zeros. So I am NOT claiming that careful “reloading bench hygiene” is essential to shooting small!
All I am saying is that I observed and recorded a significant drop in my ES when I made sure to avoid contaminating bullet jackets with case lube. This is a simple precaution that is easy to follow when loading at home. It may help you cut your ES/SD. It may help avoid that one “mystery flyer” that ruins a group. Cleaning your hands before seating bullets may seem obsessive. But the smart reloader knows that paying attention to the small details, in all respects, is the key to making ultra-accurate ammo that exhibits low ES/SD on the chronograph.
The 6mm Dasher is based on the 6mm BR cartridge with the shoulder blown forward about 0.100″ and “improved” to 40°. Case capacity is raised to about 41.0 grains. This allows the Dasher to drive 105-108gr bullets comfortably at 2970-3000 fps without over-stressing the brass. A popular load used by many successful Dasher shooters is 32.5 to 33.0 grains of Reloder 15, CCI 450 primers, with 105gr Berger VLDs, .010″ in the lands, or Berger 105gr Hybrids .015-.020″ off the lands (jumping). At the upper end this is a “warm load” and should only be used with fire-formed brass. Norma 203B is very, very similar to Reloder 15, and may be more readily available in the near future. As with any load, start 10% low and work up.
You may also have good luck with Hodgon Varget powder. Forum Member Rodney Wagner recently shot a spectacular IBS-record-setting 0.349″ five-shot group at 600 yards. Rodney was loading 32.5 Grains of Varget with CCI 450 primers and Berger 108gr BTs seated about .020″ off the lands (jumping). In preparation for fire-forming his Dasher cases, Rodney used a .257 expander to create a false shoulder on his case necks. This helps stabilizes the case with a good “crush fit” when fire-forming, but other methods of forming Dasher cases (including hydro-forming) can work well also.
Robert Hoppe, one of the top 600-yard shooters in the country, was the 2009 NBRSA 600-yard champion. In 2007, shooting a 6 Dasher, Robert nailed a 0.5823″, 5-shot group. At the time it was the smallest group ever shot in 600-yard registered benchrest competition. In 2008, John Lewis shot even smaller with an IBS Heavy Gun, but Robert’s 0.5823″ still remains the NBRSA 600-yard record, and we believe it is the second smallest group ever shot at 600 yards (in registered BR competition) by a 17-lb class rifle. Robert has been very successful in the 600-yard game, and is one of the best 600-yard shooters in the West. He knows how to wring the best accuracy out of the 6mm Dasher cartridge. Here Robert offers some tips on load development and tuning for the 6mm Dasher.
Here’s good news for reloaders. Some large shipments of propellants were delivered in the last week, and we are starting to see supplies of some popular powders start to catch up to demand. Third Generation Shooting Supply received a very large order of Alliant Powders in one-pound containers, including the popular Reloder series. If you need RL15, RL19 or RL22 you may be able to grab some before it’s gone. TGSS has already sold nearly a ton of RL15 this week.
Natchez Shooters Supplies is featuring Vihtavuori powders, and the Natchez inventory system is showing supplies “in stock” for many of the most popular Vihtavuori powders including N320, N133, N135, N540, N150, N160, and N165. All these powders (including 8-lb jugs of N133) are shown “in stock” as of this morning, but we caution that things change quickly!
NOTE FOR LATE READERS: Inventory shown for 10:00 AM April 20, 2013.
Powder Valley Inc. Partial List of In-Stock Powders
Hodgon H380 (1 lb.) — In stock at $18.35/lb
Hodgdon H1000 (8 lbs.) — In stock at $152.00 for 8 lbs.
Hodgdon Retumbo (1 lb.) — In stock at $21.35/lb
Hodgdon Superformance (8 lbs.) — In stock at $152.00 for 8 lbs.
Alliant Reloder 50 (1 lb.) — In stock at $19.15/lb
Alliant Reloder 50 (8 lbs.) — In stock at $137.50 for 8 lbs.
IMR 7828 (8 lbs.) — In stock at $147.80 for 8 lbs.
Norma 203B (1 lb) — In stock at $24.80/lb (this is nearly identical to Reloder 15)
Vihtavuori 3N37 (1 lb) — In stock at $29.95/lb
Vihtavuori N150 (1 lb) — In stock at $29.15/lb
Vihtavuori N160 (1 lb) — In stock at $29.15/lb
Third Generation Shooting Supply Alliant Powders (Partial list)
Power Pro 4000 MR (1 lb.) — 961 lbs. in stock at $19.99/lb
Power Pro Varmint – (1 lb.) — 133 lbs. in stock at $19.99/lb
Reloder 10X – (1 lb.) — out of stock
Reloder 15 (1 lb.) — 733 lbs. in stock at $20.99/lb
Reloder 17 (1 lb.) — out of stock
Reloder 19 (1 lb.) — 2579 lbs. in stock at $20.99/lb
Reloder 22 (1 lb.) — 1797 lbs. in stock at $20.99/lb
Reloder 25 (1 lb.) — 109 lbs. in stock at $20.99/lb
Reloder 50 (1 lb.) — 36 lbs. in stock at $20.99/lb
Natchez Shooters Supplies Vihtavuori Powders (Quantities Limited)
Vihtavuori Oy N3N37 (1 lb.) — In Stock at $31.49/lb
Vihtavuori Oy N320 (1 lb.) — In Stock at $31.49/lb
Vihtavuori Oy N133 (8 lbs.) — In Stock at $197.49 for 8 lbs
Vihtavuori Oy N133 (1 lb.) — In Stock at $30.49/lb
Vihtavuori Oy N135 (1 lb.) — In Stock at $30.49/lb
Vihtavuori Oy N150 (1 lb.) — In Stock at $30.49/lb
Vihtavuori Oy N160 (1 lb.) — In Stock at $30.49/lb
Vihtavuori Oy N165 (1 lb.) — In Stock at $30.49/lb
Vihtavuori Oy N540 (1 lb.) — In Stock at $34.99/lb
Editor’s Note: As with all inventory systems, there can be a variance between actual inventories and listed inventories. We are reporting what is shown “in-stock” this morning. But if the inventories are not updated in “real time” as shipments are made, true supplies may be less than what is shown.
Readers who have just recently discovered the Daily Bulletin may not realize that AccurateShooter.com has hundreds of reference articles in our archives. These authoritative articles are divided into mutiple categories, so you can easily view stories by topic (such as competition, tactical, rimfire, optics, shooting skills etc.). One of the most popular categories is our Technical Articles Collection. On a handy index page (with thumbnails for every story), you’ll find over 100 articles covering technical and gunsmithing topics. These articles can help you with major projects (such as stock painting), and they can also help you build more accurate ammo. Here are five popular selections from our Technical Articles archive.
Stress-Free Pillar Bedding. Richard Franklin explains how to do a top-quality bedding job, start to finish.
OnTarget Software Review. Our Editors test free software that measures shot groups with great precision. We explain how to use the program and configure advanced features.
Savage Action Tuning. Top F-TR shooter Stan Pate explains how to enhance the performance of your Savage rifle by optimizing the torque settings of the action screws.
Complete Precision Case Prep. Jake Gottfredson covers the complete case prep process, including brass weight sorting, case trimming, primer pocket uniforming, neck-sizing, and, case-neck turning.
Stock Painting Instructions. Step-by-step guide for stock painting by expert Mike Ricklefs. Mike shows both simple coverage and fancy effects.
We all know that reloading components are in very short supply these days — bullets, brass, powder — you name it. Every day we get calls and emails from guys trying to find these items. Here’s a tip for those of you who need high-quality brass: Midsouth Shooters Supply carries Norma Brass, and Midsouth has this brass for many popular cartridge types IN STOCK now. Here’s a partial list of unprimed Norma brass available for purchase at Midsouth as of April 12, 2013:
We had a chance to try out the new power case trimmer head from Little Crow Gunworks. Dubbed the “World’s Finest Trimmer” (WFT) by its inventor, Dale Hegstrom, this device proved fast, precise, and easy to use. When compared to a Hornady Lock ‘N Load hand-crank trimmer, the WFT processed cases twice as fast, and delivered a more uniform cut length with our test brass.
The WFT features a steel shell-holder, aluminum body, and steel drive shank. You can chuck it into any electric drill or power device that can handle the 3/8″ shank. Unlike most case trimming tools, the WFT indexes off the shoulder datum. This permits you to trim cases very quickly, without fiddling around with rim-grabbing collets, or shell-holders. Watch the videos to see the WFT in action.
WFT is Fast and User-Friendly
Mark LaFevers, our tester, was easily able to trim five (5) cases in under 30 seconds. It took quite a bit longer to trim five cases with the Hornady trimmer he used for comparison. Mark noted that, after just a 20 or so manually-trimmed cases, his arm would start to fatigue. By contrast, he could effortlessly trim 100 or more cases with the WFT. For older folks with a bit of arthritis, the WFT makes life easier. Mark observed that the WFT produces a “nice, square, clean cut”, while offering a “very fast cycle rate”. He tells us, “once you get the hang of it, you probably can trim your brass two, if not three times as fast.”
Mark really liked the WFT tool, and a WFT will be replacing his hand trimmer for big jobs. One downside is that, currently, the WFT is cartridge specific — you normally need to have a different tool for each cartridge type you trim. And there are no swappable inserts allowing you to trim different cartridge types with the same tool. However some WFT versions WILL trim different cartridge types within the same “family”, such as .270 Win and .30-06.*
Hi-Rez Video Shows “Trim-Off” Challenge between WFT and Hornady Trimmer
You should definitely watch the five-minute video below. Mark trims five cases with the WFT, and then five more with the Hornady tool. He times the operation of each device and then measures the trimmed cases. The total variation (in length) of the WFT-trimmed cases was .001. With the Hornady tool, there was a much larger spread: .007″ (seven thousandths). Mark cautioned: “Normally the Hornady tool does a bit better than this — the variance won’t be so large. But getting better results (with the Hornady) might require trimming, measuring, then trimming again. In the video I was trying to move pretty quickly and the measurements were all taken after the initial trim. Possibly, if I slowed down when using the Hornady trimmer, the OAL measurements would have been more consistent. But that just further reinforces the point that the WFT is faster.”
NOTE: If you have a fast connection, we suggest you select 720p (HiRez) and expand to full screen.
In the video below, WFT creator Dale Hegstrom demos his device and shows how quickly it can trim a large quantity of brass. Note how the WFT is attached to a common rechargeable power drill.
“World’s Finest Trimmer” Costs $69.95
The Little Crow Gunworks “World’s Finest Trimmer is available for $69.95 from various vendors including Creedmoor Sports. WFTs index off the shoulder, not the base. The case fits tightly into a steel bearing which has been machined to a specific caliber. This decouples the stationary case from the spinning cutting blade and body, giving you a smooth, exact cut each time. While the WFT makes a nice, square cut, we do recommend chamfering inside and outside after the brass is trimmed to length.
*Most WFTs are cartridge specific. Available sizes include: .204 Ruger, .223 Rem, 22-250, 6mmBR, 6.5 Grendel, 6.5×47 Lapua, 6.5 Creedmoor, 6.5-284 (and 6mm-284), 6.8 SPC, 270 WSM, 7mm Rem Mag (and 300 Win Mag), .308 Win, 300 WSM, .338 Lapua Magnum. There is a ‘5 in 1′ WFT unit that will handle .17 Rem, .221 Fireball, .222, .223 Rem, and .222 Mag. The 6mmRem unit also works with .257 Roberts and 7×57 Mauser. The .30-06 WFT will trim .270 Win, .280 Rem, and .25-06 as well. And the WFT for Ultramags works with 7mm, 300, and .338 Ultramags.
On our main Accurateshooter.com website, you’ll find a comprehensive review of the STM system for cleaning cartridge brass with stainless media. To clean brass with stainless media, start with five pounds of small stainless pins sold by StainlessTumblingMedia.com. Place these along with a gallon of water, a little liquid cleaner, and two pounds of cartridge brass in a rotary tumbler, and run the machine for one to four hours.
Forum Member Tests STM System
Our reviewer, Forum member Jason Koplin, purchased the STM media and a new Thumler’s Tumbler. He then tested the STM cleaning procedure on his own brass, including some extremely dirty and tarnished “range pick-up” brass. Jason was thoroughly impressed with how well the STM process worked — as you can see from the “before and after” photos below. Brass which looked like it was ready for the scrap heap was restored to “like-new” appearance. The process works equally well on both rifle brass and pistol brass. Jason observed that one surprise benefit of the STM cleaning procedure is a big reduction in noise. Jason said the water-filled rotary tumbler was much quieter than his vibratory tumblers.
You’ll want to read Jason’s full review which shows more before and after images. The full article features a “how-to” video created by Forum member Cory Dickerson, the young man who pioneered the stainless tumbling process and founded STM. The video shows how to load brass, media, and cleaner solutions into the tumbler, and how to separate media from brass once the tumbling is done.
There is a new player in the field of elite die-makers: Whidden Gunworks. John Whidden’s Georgia-based company is producing outstanding full-length sizing dies and micrometer-top seater dies for 7/8-14 thread presses. The dies look great, work great, and produce very straight and accurate ammo. The Whidden dies are finished beautifully inside and out. They are priced competitively and they are available for popular “extreme accuracy” cartridges such as the 6PPC, 6mmBR, 6mmBRX, 6 Dasher, 6XC, 6.5×47, .260 Rem, .284 Win, and .308 Win (and more). If you are looking for a die set for your new precision rifle, you should definitely check out the Whidden dies. Two-die set, FL Sizer and Micrometer-top Seater, costs $184.99. Sizer die alone is $74.99, while Seater die alone is $109.99.
Many of our Forum members have started using Whidden dies — and they are reporting very positive results. I personally own and use a set of Whidden dies, and I am very, very impressed with them. Here’s my report:
Editor’s Report on Whidden Dies I have a set of Whidden Gunworks dies for my personal 6BRDX (a chambering similar to 6 Dasher but with longer neck). The dies are excellent and they produce very straight ammo. My loaded rounds (made with a Whidden bushing-type FL sizer and Whidden micrometer-top seater) are showing less than .0015″ run-out measured on the bullet, with the majority closer to .001″ run-out. (This is with Lapua Scenar L bullets, which have great jacket uniformity and concentricity.)
One thing I immediately noticed about the Whidden seater die is that there is a very close correspondence between the seater “hash marks” and true changes in seating depth. By this I mean when you dial a value change of 10 on the micrometer scale, you get very close to a .010″ change in seating depth. It is not perfect, but it is definitely more precise than most other micrometer-top seater dies I’ve used (both hand dies and 7/8-14 thread screw-in types).
Cartridges loaded with my Whidden sizer and seater dies have proved very accurate. My 6BRDX is shooting in the mid-ones for five shots at 100 yards. I also have a micrometer-top Wilson inline seater die that was custom-bored with my chamber reamer. As far as I can tell, the ammo loaded with the screw-in Whidden seater is every bit as accurate as rounds loaded with the Wilson die using an arbor press. Additionally, with the Whidden micrometer die, I can hold extremely tight tolerances on base-to-bullet-ogive lengths.
In the past, with my 6mmBR, I favored an inline die because I thought it offered better control over seating depth. But given how well the Whidden seater works, I’m not sure I’d gain anything with my Wilson hand die. At least when used with a quality Harrell’s benchrest press, the Whidden seater gives up little or nothing to the hand die, and that’s big news in my experience.
You will like the look and feel of these Whidden dies. The finish inside and out is very, very good — the dies have a quality feel and run very smoothly. Both the sizer and seater have a fluted section — this offers a better “grip” when you’re screwing in the dies. The outside of the seater has a smooth, gloss-anodized finish — it exudes quality. The markings on the seater’s micrometer ring are crisp and very legible, with large, high-contrast white-on-black lines and numbers.
One other very cool feature of the Whidden sizing dies is that custom-sized tapered expanders will soon be offered. Whidden plans to offer expanders in .0005″ (one-half thousandth) increments. This is great if you have, say, a .265 bushing and a .266 bushing but you want just a little less neck tension than the .265 offers. With the tapered expander, I can use a 0.265 bushing followed by an 0.2655 expander — allowing more precise control of neck “grip”.
Whidden Die Features
Die Dimensions well-matched to PT&G reamers used for match chambers.
Sizing dies spec’d for easy chambering and extraction without overworking brass.
All sizers include shoulder datum collar to measure shoulder “bump” and headspace.
Neck bushing or no-neck bushing configurations.
Bushing dies use standard Redding/Wilson type bushings.
Neck diameter of non-bushing FL sizers can be set to customer specification.
Extended threads on short cartridge sizer dies such as BRs.
Coming soon: custom expander balls (in half-thousandth increments) to adjust neck tension and provide minimum working of the case neck.
Seater: Floating sleeve on micrometer seater enhances concentricity of loaded rounds.
Seater: Large, high-contrast markings for easy adjustment.
Custom Dies for Wildcats or Your Cartridge
Custom-made for your wildcat or standard cartridge.
Can work from fired brass or a chamber drawing to match your chamber exactly.
Neck-bushing die, or no-bushing die with neck diameter bored to customer specification.
Available Die Sets
Here is the current caliber list. Micrometer seaters are available in all calibers listed below except 22BR and 22 BRX.
John Whidden Talks about Sizers, Seaters, and Expanders
There are two sides to our die business. First we are stocking dies in many calibers that are of interest to those who visit this website (such as the 6PPC, 6mm Dasher, 6.5×47 Lapua, .260 Rem, 7mm Shehane, .308 Winchester). These dies are a good fit to the “match chamber” reamers and very few people with these calibers should have to have “Pure Custom” dies made. We have both sizers and micrometer-top seaters ready to go for the many cartridge types listed above. The sizer dies will include a shoulder datum collar that makes it easy to measure shoulder “bump” during the full-length sizing process. This is important to control headspace precisely.
On the “Pure Custom” side, we have a huge amount of flexibility. We can make one-of-a-kind sizers and seaters for wildcats in a short period of time and at an excellent price. We can work with the customer to make full-length sizers, neck sizers, shoulder bump dies, small base dies, or most anything else they can need. We can of course provide micrometer-top seaters for these cartridges as well. We can make non-bushing sizers with specific neck inside diameters tailored to customer specifications.
We will also be offering custom-sized expanders. These expanders will fit our dies as well as Redding dies. Our tapered expanders will be available in .0005” (one-half thousandth) increments for the common calibers. In our shop we have had excellent results using expanders in the dies as long as the expanders provided the correct amount of neck tension and didn’t overwork the brass. Expanders have gotten a bad reputation in recent years but we find them to be excellent tools when the same precision is applied to their use that careful handloaders apply to the rest of their process. Expanders can be most valuable for those who choose not to neck-turn their brass (because the expander pushes neckwall variations to the outside).
One last thing — many gunsmiths with their own wildcats (or “specialty” chambers) have asked us to provide dies for their customers. We gladly do batches of custom dies and encourage gunsmiths to contact us. — John Whidden
The funnels are priced by size. The 3″-long model is $24.00, the 6″-long model is $27.00, and the big 10″-long model is $31.00. Prices include one (1) adapter. These high-grade funnels will help you load faster and easier, with fewer spilled kernels. We use these funnels and they do work well. The appropriate collars fit your .223 Rem, 6PPC, 6mmBR, Dasher, 6XC, .260 Rem, .284 Win, and .308 case necks just right — not too loose, not too tight. Kernels flow smoothly through the tube without sticking to the sides. The aluminum top section does not seem to attract a static charge so you don’t have to waste time brushing kernels off the funnel after use. We like this product. For high-volume precision reloaders, these funnels are worth the money.
You can use this same technique even if you prefer a sharper angle chamfer tool for your initial inside-neck chamfering operation. Reverse your tool gently a couple turns to burnish and smooth the cut. And always remove brass chips and shavings before you run the tool backwards (in the non-cutting direction).
How would you like to lower your Extreme Spread (ES) and Standard Deviation (SD) significantly by a simple procedure that takes seconds and costs almost nothing?
The 6mm Dasher is based on the 6mm BR cartridge with the shoulder blown forward about 0.100″ and “improved” to 40°. Case capacity is raised to about 41.0 grains. This allows the Dasher to drive 105-108gr bullets comfortably at 2970-3000 fps without over-stressing the brass. A popular load used by many successful Dasher shooters is 32.5 to 33.0 grains of Reloder 15, CCI 450 primers, with 105gr Berger VLDs, .010″ in the lands, or Berger 105gr Hybrids .015-.020″ off the lands (jumping). At the upper end this is a “warm load” and should only be used with fire-formed brass. Norma 203B is very, very similar to Reloder 15, and may be more readily available in the near future. As with any load, start 10% low and work up.
Here’s good news for reloaders. Some large shipments of propellants were delivered in the last week, and we are starting to see supplies of some popular powders start to catch up to demand. 
“World’s Finest Trimmer” Costs $69.95
On our main 
Available Die Sets
There are two sides to our die business. First we are stocking dies in many calibers that are of interest to those who visit this website (such as the 6PPC, 6mm Dasher, 6.5×47 Lapua, .260 Rem, 7mm Shehane, .308 Winchester). These dies are a good fit to the “match chamber” reamers and very few people with these calibers should have to have “Pure Custom” dies made. We have both sizers and micrometer-top seaters ready to go for the many cartridge types listed above. The sizer dies will include a shoulder datum collar that makes it easy to measure shoulder “bump” during the full-length sizing process. This is important to control headspace precisely.
