This story first ran ten years ago. But to mark our long-standing friendships with shooter Joe Friedrich and chassis builder Gary Eliseo, we wanted to reprise the article for a new decade. Joe’s Eliseo-chassis 6BR rifle delivered some of the most stunning factory ammo accuracy we’ve ever seen, in any rifle, in any caliber.
Amazing Accuracy from 6mmBR Tubegun
What kind of accuracy do you think a tubegun can deliver with factory ammo — during barrel break-in? Perhaps 0.6″ at 100 yards, half-MOA if the conditions are perfect? Well you may want to change your preconceptions about tubeguns — and factory ammo. This Eliseo R5 repeater, smithed by John Pierce with a Pierce CM action and Broughton 5C barrel, shot the Lapua 90gr factory ammo into flat ONEs during the break-in session. A day later, in tricky 8-14 mph winds, the gun nailed a witnessed and software-measured 0.174″ 5-shot group using the 105gr factory ammo. That would be impressive for a “full-race” benchgun with precision handloads. For an across-the-course rifle shooting factory ammo, it’s pretty amazing.
Eliseo Tubegun Shoots in the Ones
This accurate rifle belongs to our friend (and designated expert trigger-puller) Joe Friedrich. During the initial break-in session, since his reloading dies had not yet arrived, Joe decided to start with some Lapua factory-loaded 6BR ammo he had on hand. After doing a few two-shot-and-clean cycles (with patches and nylon brush), Joe decided to try a 3-round group just to see if the Broughton barrel had some potential. To his astonishment, the Eliseo R5 put three rounds in 0.100″ (photo below left). Joe then cleaned the barrel again, shot a couple foulers and tried a 4-shot group. The results were just as stunning — 4 shots in a mere 0.104″ but three in virtually one hole (photo below right).
You Can’t Believe How This Gun Shoots
Joe called your Editor and said “You can’t believe how this gun shoots with factory ammo!”. So we arranged a photo session for the next afternoon, where I could verify the rifle’s accuracy. Well it turned out the conditions were way more challenging than when Joe broke in the barrel the day before. Winds were running 8-14 mph and were swinging through 180 degrees half-way down the range. Joe fired a few 90s through the Oehler chronograph at my request, then opened a box of Lapua 105gr factory ammo. It took about four rounds for the barrel to settle in after being cleaned the night before. Then Joe got serious, and with your Editor looking over his shoulder, he drilled a 0.174″ five-shot group in switching winds, doping every shot. Joe felt the gun could have shot tighter but he missed one wind call.
Serious Accuracy with a Multi-Purpose Rifle
So there you have it — a tubegun that shoots in the ones with factory ammo. Joe says that, at least with the 90s, the Elesio R5 shoots as well as his 6 PPC. Joe stressed that “steering the tubegun is hard work. You really have to concentrate compared to a purpose-built bench gun like my PPC. With the tubegun, everything has to be perfect on every shot — hand position, cheek position, stock position in the bag. If you’re off just a little bit, it’s easy to steer the gun the wrong way and send a shot out of the group.”
Accuracy Great But Fouling Heavy and ES Could Be Better
Have there been any negatives to Joe’s 6BR tubegun experiment so far? Well, the Broughton 5C barrel, while phenomenally accurate, shows signs of being a bad fouler. Copper built up pretty quickly over the first 25 rounds or so. We saw best accuracy with a recently-cleaned barrel. Hopefully the fouling will lessen as the barrel polishes in with use. And the canted land barrel is slower than average with the factory ammo. Lapua rates its 90gr naked-bullet ammo at 2950 fps with a 26″ tube. In Joe’s 27.5″ barrel we only averaged 2901 fps. With the 105gr factory ammo, which is rated at 2790 fps, we averaged just 2694 fps. That’s quite disappointing. Also the ES on the factory ammo, slightly over 50 fps for both bullet types, wasn’t particularly good. Still, the overall results were stunning. This gun shoots better than many long-range benchrest rifles running carefully-developed handloads — and it does that with factory ammo, right out of the box.
Joe Friedrich is a superb benchrest shooter, who has won many matches and set National Records in ARA rimfire benchrest competition. Here is Joe with “Sweet Pea”, his favorite .22 LR rimfire rig. With over 100,000 rounds through the Benchmark barrel, this well-worn rifle set an ARA 4-target Aggregate record! READ about Sweat Pea Record HERE.
Specialty Pistols — Report from Ernie Bishop in Wyoming
For those who know of me in the shooting world, you would probably know me in one of two ways: Dealer for SEB Rests or someone who does most of his competing, varminting, and or hunting with specialty pistols. These are typically bolt-action, single-shot rigs that can be used with a bipod. They can seem very similar to a pistol-grip rifle, but without a conventional buttstock.
My interest in all things specialty pistols (Remington XP-100, TC Contender, MOA Maximum, Pachmayr Dominator, H-S Precision HSP, etc.) goes back to the early 1980s. Most of the specialty pistols listed are no longer made, so when I discovered that Kauger Arms was making two, I was excited. I have not had much time to shoot my new Kauger “Black Widow” chambered in 6.5×47 Lapua. But so far, the experience has been fun, even though I have not taken it prairie dog shooting yet or hunted big game with it. For this report, I went to my friend Dan’s place as one can load in the house, and simply shoot off his back porch.
When thinking of a precision shooting platform, most of you would not consider a wood back porch as ideal. But we managed a 0.179″ 3-shot group at 100 yards using a Harris bipod and a small leather bag. Yes the Black Widow can shoot! My load was Lapua brass, Federal 205M primers, Varget powder, and the Hornady 123gr A-Max, with a MV of 2514 fps. I selected the Hornady 123s with prairie dogs in mind. As shown in the top photo, the scope on the Black Widow is a Sightron S-III 6-24 with a Holland’s scope level. The Black Widow also sports a Holland’s Radial Baffle brake.
Here is the Black Widow with a different scope base and scope, ready to go on Dan’s porch.
The day we planned to shoot prairie dogs was windy, so we headed to public land nearby and set up steel to get ballistics drop info and simply to play at distance. We had 5″ steel at 220 yards, 10″ steel (diamond) at 510 yards, and 10″ steel (square) at 650 yards. Wind was from 8 mph to just over 20 mph, so the little 123 grainer was getting tossed about, while keeping us humble all at the same time. Regardless of the gusty winds, I considered the session a success!
Kauger Arms has been making parts for a number of companies in the firearm industry for over 20 years. In 2014 when things slowed down for them, they decided to start building rifles and decided to make their own actions. Good decision — these actions, which are machined in a single process to keep everything true to the bore, are great. Bolt manipulation with Kauger’s action is the smoothest I have ever experienced.
Tim Kauger explained features of his actions to me. The Kauger cock-on-opening action has a Rem 700 footprint for action holes and trigger shoe. The semi-coned bolt features a floating bolt head which is slightly smaller than the bolt body. The firing pin assembly is 1/4-turn removable. There are user-changeable bolt body and knob options. There is a side bolt release above the stock line. All moving surfaces are nitrided. This can be ordered single shot, feed rails or DBM cut. Also the long action will accept up to a .338 Lapua/.300 Norma Mag if ordered that way (with 1.25″ barrel cylinder).
Kauger Arms offers a right-hand or left-hand grip, which is very comfortable. I shot the Black Widow both right-handed and left-handed with no problems whatsoever. Kauger Arms can build the Black Widow in many more chamberings than the two that are listed on the KaugerArms.com website.
New left-bolt/left port action from Kauger Arms — To the specialty pistol shooters reading and to those considering entering the SP world, Kauger Arms has listened to your requests and is working on a left bolt/left port short action that will be offered either as a single-shot action or with bottom metal. You grip the pistol with your right hand, then run the bolt with your left-hand.
Specialty Pistol 2 — The Camo .223 Remington HSP
Here is another one of Ernie Bishop’s specialty pistols. This eye-catching camo-stocked rig was crafted by H-S Precision. Sadly, H-S Precision is not making these HSP pistols anymore. This .223 Remington features a 1:7″-twist, 15-inch-long H-S barrel fitted with the “H” Brake. On top is a Burris XTR-III 5.5-30x56mm scope with SCR 2 MIL reticle and Burris rings.
Great Results with Varget + 77gr Sierra TMKs
Ernie tells us: “For a load, I have been running Lapua brass, Rem 7.5 primers, Varget, and the 77 grain Sierra TMK. Muzzle Velocity is 2675 FPS. As you can see, it shoots pretty well. Shown at right is a measured 0.265″ 3-shot group at 100 yards, shot from Harris bipod and small field bag.
Previous to this, I was shooting Federal Match ammo with the 77 grain SMK (MV was 2500 fps), with prairie dog kills past 600 yards, and have played on steel out to 1000 yards. This H-S specialty pistol is great for young or old alike, for novice shooters or experienced shooters. Everyone needs a fast twist .223 Remington!”
Here is my friend Dan shooting the .223 Rem HSP with factory ammo during a prairie dog trip.
Here is the view from 9500 feet ASL. The SRS in 7mm Rem SAUM almost outran the Swarovski laser…
7mm RSAUM in a bolt-action bullpup? Yes it works. A talented shooter, who calls himself “ColdboreMiracle” in social media, has a Desert Tech SRS-A1 rifle chambered for the 7mm RSAUM, and it hammers. The 7mm Remington SAUM (Short Action Ultra Magnum) is popular with F-Open competition shooters. It can also work well for long-range hunting and tactical tasks. Learn more about the 7mm Remington SAUM in our 7mm Cartridge Guide.
ColdboreMiracle owns the SRS-A1 “covert” model, which has a shorter handguard than the standard SRS-A1 model shown below. Desert Tech now offers an SRS-A2 model which has an M-LOK handguard and some refinements to the chassis.
Here is a detailed video review of a Desert Tech SRS chambered in .308 Win. You can see a close-up of a 100-yard 5-shot group at time-mark 6:25:
Here is a review of the newer SRS-A2 Covert (shorter model), after 1000 rounds. The reviewer believe the SRS bullpup’s shorter length offers some advantages for precision shooters:
ColdboreMiracle says the bullpup design has many advantages: “The Stealth Recon Scout (SRS) rifle from Desert Tech is a bullpup-configured precision rifle with a shorter length than many carbines. The SRS has a multitude of barrel options that can be swapped in under a minute — all of them come with a 1/2-MOA accuracy guarantee and return to zero. The SRS’s bullpup design puts the rifle’s COG closer to the shoulder, making the rifle balance better off-hand. The straight-line geometry of the SRS makes recoil seem lighter, and barrel hop is reduced, allowing the shooter to stay on target better. It takes a little getting used to, when converting from a traditionally-configured bolt gun. But once you do, you won’t go back.” To learn more about this rifle (and other Desert Tech arms), visit ColdboreMiracle’s Facebook Page and YouTube Channel.
The 7mm RSAUM — Why It Was Chosen for this SRS
ColdboreMiracle explains how he selected the 7mm Rem SAUM chambering for his Desert Tech SRS Bullpup: “I just did a comparison between barrel life, velocity, brass, etc. and came to the SAUM. I can tell you this, if you go with one for your SRS, make sure you use long bullets like the 183 or 195, and seat them long. That will aid in smooth cycling.”
Mr. ColdboreMiracle tested the new generation 183gr Sierra MatchKings (item # 1983). These impressive projectiles are “tipped” at the factory. Claimed G1 BC is a lofty 0.707 (at 2300 fps and above). We have heard other reports that these bullets “hold waterline” exceptionally well at 1000 yards. That indicates the bullet-to-bullet BC is very consistent. No doubt the factory uniforming/pointing of the bullet tips helps in that regard.
As you can see, these 183-grainers shoot well in ColdboreMiracle’s SRS rifle. Here are five shots at 100 yards. That’s very impressive for a tactical-style rifle shot from a field-type bipod.
ColdboreMiracle says: “This is the only reason I need to shoot Sierra bullets. On the right (above) you can see the results of the 183gr SMK from my 7mm SAUM. Five shots at 100. A huge thanks to Mark at Short Action Customs, LLC for [chambering this barrel] for my Desert Tech SRS.”
7mm Remington SAUM — Key Considerations
In some respects, the 7mm SAUM cartridge may be better than the 7mm WSM. The 7mm SAUM holds less powder — but that’s a good thing, since the capacity is more than adequate to do the job. You can drive the 180s at 3000 fps with a SAUM using less powder than with a WSM. Additionally, the SAUM case has a slightly longer neck. This gives you greater flexibility in bullet seating. With a long neck you can set the throat so the long 180+ graing bullets are above the neck shoulder junction, yet you can still seat shorter hunting bullets close to the lands. Additionally, long case necks, some believe, cause less throat erosion than shorter necks. That’s not “hard science” but it is certainly a view shared by many experienced shooters. The long neck is one reason many varminters favor the 6mm Remington over the .243 Winchester.
7mm RSAUM Is More Efficient than 7mm WSM
7mm RSAUM shooter Steven Ikeeda tells us: “I decided that some type of 7mm was the ticket for doing well at 1000-yard matches, especially if one could drive the high-BC bullets at 2900+ fps. Looking over various 7mm cartridges that could produce those velocities (and didn’t require case-forming), I was impressed by the 7mm SAUM and the 7mm WSM. According to the load manuals, the 7mm WSM offered a bit more velocity than the 7mm SAUM. However, to achieve its small velocity advantage, the larger 7mm WSM had to burn 7-10% more powder than the 7mm SAUM. (The 7mm WSM has 81.0 grains of capacity vs. 73.6 grains for the 7mm SAUM.) The SAUM is a very efficient case. It looks like a 6.5×47 Lapua on steroids.”
Some of our Shooters’ Forum members have asked for t-shirts with AccurateShooter.com logos. Sorry folks, we don’t offer those for sale, but we have searched the internet and found ten great t-shirts for gun guys and gun gals. Most of these shirts are available is multiple sizes, and many offer color choices. You’ll find over 100 more gun-themed shirts at the Etsy.com online store.
Click on each shirt image for more specs and purchase options:
One of the most popular features of our Shooters’ Forum is the Official ‘Pride & Joy’ Rifle thread. There you’ll find dozens of interesting rifles, with photos and descriptions supplied by proud owners. Today we’re spotlighting one of the more interesting ‘Pride & Joy’ rifles unveiled this year, a Mosin Nagant “senior citizen”. This 72-year-old Russian bolt gun is not like any Mosin Nagant you’ve ever seen before. It has been brought into the 21st Century with a handsome target stock and some first-class upgrades, including Lothar Walther barrel and Timney trigger. Here’s a look at a very nice Russian rifle, belonging to Forum member Ben C. (aka “Grimstod”):
Video Shows Rifle Shooting Sub-Half-MOA from Bipod (in the Snow):
Name of rifle: Smyert Mk3 (Modified Mosin Nagant)
Make: Izhmekh/Izhevsk (“Izzy”) High Wall
Model: 91/30 | Year: 1942
Scope mount: Rock Solid (looks like an action sleeve)
Scope: SWFA 20x42mm MRAD
Gunsmith: Sheppard
Bolt handle: Rock Solid with Surgeon tactical handle
Bipod: Versa Pod
Total Weight: 18.6 lbs
Grimstod’s Mosin Nagant Custom Shoots Under 0.5 MOA From Bipod
Even in harsh winter conditions, the rifle shot well. (I guess we should expect that for a Russian gun). The photo below shows a group shot from bipod. (The video shows Grimstod’s snow-bound range session). Grimstod calculated the group at 0.394 MOA measuring from outside edge to edge. Using our On-Target software, which measures center to center of most distant shots, we came up with 0.428 MOA. Still that’s impressive for an ancient action being shot in the dead of winter with snow falling. To learn more about this rifle (and view photos of the build process), visit the SurplusRifleForum.com.
Here is Tye Sim’s .270 Win Mountain Rifle: “This is off a trued and blue-printed Rem 700 action. I love it.”
For today’s Sunday GunDay feature, we thought we’d present a selection of rifles featuring both cool gear and scenic venues. We’ve got quite a mix — hunting rifles and competition rigs, full customs as well as factory rifles. And there are some interesting calibers including 6.5 Creedmoor, .270 Win, .308 Win, plus a couple WSM variants. Enjoy our Sunday lineup!
To begin, here is the beautiful Blair Atholl range in Scotland. Owner Gary Costello posted: “Great day today, weather was interesting but not as bad as we thought!” Gary, a top F-Class shooter in the UK who often runs a .300 WSM, has been featured in a previous Sunday GunDay spotlight story HERE
Andrew Stone is an F-Class shooter from the Southern USA. Here his F-Open rig is set up for load testing from the bench at his beautiful, tree-lined home range. Targets are at 600 yards. Andrew is using a SEB front coaxial rest and LabRadar chronograph mounted on an aftermarket tripod.
In the photo above is Brian Harder’s handsome .308 Win F-TR rifle. This features a Kelbly action, McMillan stock, and Vortex scope with level. Up front is a SEB Joystick Bipod (Joy-Pod) with accessory ski-type feet. Note that Brian runs a front scope extension tube (sunshade), and a mirage shield on the barrel. These items do make a difference, particularly on hot summer days!
Here’s another British Beauty. This is the 7mm-270 WSM F-Classer belonging to Forum member Ian B. (aka “Elwood”). It features a Stolle Panda F-Class action, 32″ straight-contour Bartlein barrel, and a custom Joe West stock, modified by Ian and then hydro-dipped in brilliant blue by Hydro Graphics in the UK.
Factory rifles can be interesting too. That’s pretty impressive accuracy shown by Steven Castleman’s Bergara B14 HMR chambered in 6.5 Creedmoor. On this day Steve was shooting Hornady factory ammo loaded with 147-grain ELD Match bullets.
Here’s a stunning silhouette of a Savage 6.5 Creedmoor. Ed Whipple posted: “Borrowing a Savage 10 BA Stealth from my buddy Ron. He wanted a 100-yard head shot on a hog. I’m not listening to Ron any more. Federal Fusion bullet ain’t messing around.”
This would be an amazing group at 100 yards. But this 5-shot bughole was shot at TWO HUNDRED yards in competition by Bart Sauter of Bart’s Custom Bullets. And he did it with a borrowed barrel!
Be amazed. This five-shot group was shot at 200 yards in competition by bullet-maker Bart Sauter. Bart shot this astounding group with his 10.5-lb Light Varmint benchrest rifle at the recent East-West Match in St. Louis, Missouri. Had Bart been shooting an IBS match, this would have been a new IBS World Record, beating the .091″ by David Farrar in 2006. This .088″ group missed the NBRSA 200-yard 5-shot group record by a whisker — .013″ (thirteen thousandths). The listed NBRSA LV 200-yard Group record is 0.075″ shot by Johnnie Stewart a decade ago.
New record or not, this is one remarkably impressive group, shot by one very talented shooter and bullet-maker. Bart tells us he initially “held center” for the first three shots in the group. Then, watching his wind flags he noticed slight increase in the left-to-right condition, so he held 0.200″ to the left on shot 4 and it worked. Before shot 5, Bart detected another slight change, so he held 0.300″ left for the fifth and final shot. He explained: “If I had not held off for those last two shots, this group would have been about a flat four (0.400″).” Well done Bart!
“First three … bang bang bang … all went in one hole. Then I held left on shot 4 and it worked. On the last shot I held a little more, got lucky and it went in.” — Bart Sauter
In our Shooter’s Forum, Bart posted “This is my personal best-ever 5-shot group at 200 yards. I knew it was small, but was shocked to see it was a Zero! This will be a range record and record for the East/West match. Last group of the day! A nice way to end the match!”
Here is the 6PPC LV rifle that shot the .088″ group. Yes that’s a concrete shooting bench inside a pretty nice cabin with hunting trophies on the walls. Bart explained: “We reload and shoot out of the Monkey Hut, especially during the winter. Most of the time we shoot outside at 100/200 from a a three-bench range.
Amazing Group Shot with Borrowed Krieger Barrel!
There’s a very interesting side-note to this story. You see Bart doesn’t even own the Krieger barrel that delivered this amazing .088″ 200-yard group. That’s right this superb barrel was a “loaner” — borrowed from Bart’s buddy Gary Sullivan. [Editor: Oh that we could all be so lucky with borrowed components.] With Sullivan’s blessing, Bart has since loaned the barrel yet again to ace Billy Stevens, who will be using it at the World Benchrest Championship in Canada, July 14-21, 2019.
This photo shots Bart on the right and his good friend Billy Stevens on the left. Bart notes: “Billy is a 2-time Super Shoot Winner and 3-time USA World Benchrest Team member!”
Bart Sauter’s LV 6PPC Rifle Specifications
Chambering/Caliber: 6PPC
Gunsmith: Stevens Accuracy
Action: BAT DS RBLP Right Eject
Trigger: Jewell
Stock: Scarborough Carbon Fiber over Wood Skeleton
Barrel: Krieger — and it was borrowed!
Tuner: Bukys TSI Tuner
Optic: 40x45mm IOR-Valdada 30mm tube
Rings: Benchsource Double Rings
Front Rest: Farley Joystick
Rear Bag: Edgewood Bunny Ear, very soft, gray leather — special order from Bruno’s.
Front Bag: Edgewood — same soft gray leather.
Here is Bart’s target with a bullet removed. Bart was shooting his own 6mm 68gr Avenger bullets, a double-radius ogive design. The Avengers were seated about .004″ away from the lands: “I tried going into the lands and that didn’t seem to work, then I backed it off four thousandths [from contact] and the rifle liked that.” Bart drove those 68gr Avengers with a stout load of Accurate LT30 powder running 3407 FPS.
Bart’s Comments on His Components and Accessories
OPTICS — Bart likes his new 40x45mm IOR-Valdada Benchrest Scope. He says that, so far, it has proved very reliable and holds zero exceptionally well. This new design features a worm drive side-focus, oversized ocular with true +/- diopter adjustment, long eye relief, and fast-focusing reticle. The 40X Valdada also boasts superb HD “double-compressed” Schott glass from Germany.
TUNER — Bart says the Bukys TSI Tuner definitely helps. He notes that once he finds the “sweet spot” for his barrel he can normally leave it alone: “With that type of tuner, I have to be in a very dire straight to move it. Normally I will set it for the lifetime of the barrel.”
REAR BAG — Bart’s rear bag is an unusual Edgewood with softer gray leather. He says this was a special order by Bruno Shooters Supply. Bart likes how the rear bag works with his carbon-stocked 10.5-lb rifle: “With PPCs we ‘ride on the ears’ — this older bag just seems to work really well for that style.”
SUPER FEET — Bart told us he uses Benchsource Super Feet for his front rest: “The bench tops at St Louis are very slick. Before I set up I’ll use a spray bottle with water and wet the bench where the Super feet and rear bag will go. This really helps to keep things from sliding around!”
Gary Costello recently won the Great Britain National League 600-yard Championship in F-Open class. Gary managed that impressive win despite Storm Hannah which caused torrential rain and 40 mph winds during the match, held at the Diggle ranges. Gary, a Forum member, reports that conditions were hellacious: “The weather was terrible, with horizontal rain and winds in excess of 40 mph. In fact, some shooters got blown clean off the target and many complete misses occurred.”
There’s a special story here, as Gary had been battling a life-threatening illness for many months. Gary told us: “This was my first National Competition since September 2018. I contracted a serious heart virus in October 2018. I was critically ill until January 2019. After undergoing treatment and 100% rest I recovered slowly, my focus was the 600-Yard Shoot in April. I am now 70% there and hopefully in another 4-6 months I hope to make a full recovery.” [Editor: Gary, we are glad you are on the road to recovery.]
In today’s Sunday GunDay story, we feature Gary’s American-crafted .300 WSM F-Open rifle. Note that Gary’s rifle has a Ezell barrel tuner and a recoil-reduction system in the buttstock. The .300 WSM does generate quite a kick with those big .30-caliber bullets.
Gary Costello’s .300 WSM F-Open Rifle
BAT M Action and Cerus Stock
This rifle was purchased from Jim Fowler (FalconPilot on the AccurateShooter Forum). This SG Rifles gun, crafted by smith Thomas “Speedy” Gonzalez, is a .300 WSM with BAT ‘M’ action (with nitrided bolt) and Cerus riflestock. Gary owns two other Speedy-built rifles.
Gary tells us: “My BAT ‘M’ action is a multi-port so I feed with my left and it ejects on the right. Speedy has worked on the firing control and timing, and I fitted the roller-cocking piece to aid smoothness and speed.” The fluted shroud is Speedy’s signature for fire control work.
Stunning Lenzi Co-Axial Front Rest
Gary tells us this impressive joy-stick rest “is a superb piece of engineering .. made by my good friend Alberto Lenzi.” Note the large stable base, and the deluxe counter-balance weight on the front end. Gary also uses a very nice leather rear sandbag crafted by Lenzi.
Riflescope — Prototype March 10-60×56 High Master
Gary Costello’s company is the European distributor for March Scopes. Gary was testing this scope as it has a new temperature-tolerant lens system to be released later this year
.300 WSM Load Details — H4350 with Berger 215gr Hybrids
Gary was shooting pointed Berger 215gr Hybrid bullets in Norma .300 WSM cartridge brass. The powder was Hodgdon H4350 with Muron KVB7 primers. Gary say his load runs around 2850 fps, and is very accurate. To demonstrate, here is a three-round, 100-yard test target, with a group measuring in the ones. Pretty impressive for a big bullet and a short magnum cartridge.
The UK has some wonderful places to shoot. This photo was taken at Blair Atholl in the Highlands of Scotland. Gary says “This is one of my favorite ranges and probably the hardest range to shoot in the UK. Due to the topography of the range you have to alter elevation as well as wind for pick-up and let-off. They say ‘Diggle Ranges Bark’ but Blair Atholl Bites!”
Blast from the Past — At Blair Atholl Ranges in Scotland
One of Europe’s very best F-Class competitors, Gary is no stranger to the winner’s circle. Here he is at the Blair Atholl Ranges in Scotland after a major victory a few seasons back. Gary says: “Blair Atholl, in the Estate of Blair Castle, is very scenic. The range is very tricky and is known as the hardest range in the UK to shoot due to the location of the targets cut into the hillside and valley. When the wind is at full value you often have to add one-half MOA elevation to every 1 MOA of wind. So thinking wind and elevation every shot is very difficult. I won this match some time ago and I do not recall the score. However it was a decisive win, and all matches in the competition were held at 1000 yards.” Gary was using a different rifle, but it also was a .300 WSM with a BAT action. His load was Hodgdon H4831 with Berger 215gr Hybrids, Murom primers, and Norma brass.
The event was the first GB National League event of the year, our only short range (600-yard) match. This is actually one month later than usual in hope the weather would be better, sadly that wasn’t the case!
I won the Championship, five points clear of runner-up Ian Boxall. My final score was 241-18V out of a maximum of 250. The course of fire was reduced due to Storm Hannah on Saturday. It was decided by our committee that for safety we should shoot under cover (Diggle has a 600-yard covered firing point). The goal was to get at least one match to allow the competition to continue on the Sunday.
When I saw the condition and the flags I decided I needed to shoot as quick as possible as wind speed and direction were changing in seconds….
So I shot like stink only watching one flag and the other targets and my shot indication on the target screen. My first sighter was a score One left (a FIVE on the U.S F-Class target). But after adjusting, my second sighter was a One right — so there were pick-ups and let offs of about FIVE MOA!
I split the difference and went for score, my first shot was a Four (Nine on USA target) which I then adjusted on and held accordingly for the rest of the string using the other targets as indication and the one flag I had identified, it went pretty well.
Day Two (Sunday) weather was completely different, much better with no rain. We were first up at 0900 and the winds were light with subtle changes. This was a two sighters and 20-shot match, I started well with two V sighters which were converted, my partner Richard Sharman also had a good start and we proceeded through the string shooting Vs and Fives until Richard’s shots started to not register, this happened three times so it was decided I would continue and Richard would shoot again on another target. This caused a lot of delay and disruption. I had lost my path and wind, due to the delay I was allowed a non-convertible sighter which was a Three. It took two further shots to get back into the swing and I then recovered and ended the shoot with a 97-10V.
For the Final Match, the wind had picked up and was causing quite a few lost points and curses. I knew I was three points clear going into this Final Match so I had to play it real safe not to drop shots and lose critical points. I favored a left 4-5 Ring hold so not to get caught on the pick-ups. I use the March MTR-2 reticle, on 40X this reticle is subtended at exactly one-half MOA and brackets the F-class target perfectly. I was not concerned about the V bull at this time, the plan paid off and I dropped two points only.
We know our readers like accurate rifles — the more accurate the better. You guys also love really great craftsmanship and state-of-the art componentry. To satisfy that lust for amazing, accurate rifles, we’re starting a new feature — Sunday GunDay. We’ll try to do this a couple Sundays a month, provided we have some great candidates. For our first Sunday GunDay feature, we are presenting a stunning .284 Win F-Open match rifle owned by David Christian of Team Borden/Brux/Lapua. This impressive rig is as good as it gets in the F-Open game. The write-up is by David’s friend, Forum member F-Class John.
Tips For Competitors from David Christian
1. Tracking is Really Important. I learned this lesson from Bill Brown. Make sure your rifle is tracking exactly on your bags. If you slide the gun back and forth and it does not line up on your original aim point, something is out of alignment with you rear bag or mat and needs to be adjusted.
2. Wind Calls — Be Brave. Don’t be timid with your wind calls. It is better to err with a slight over-correction, rather than miss a change entirely.
3. More Data is Good. Keep track of as much data as you can so that you can learn from it. For example I shoot as much as I can with my chrono and track my load speeds so that I can tell if I am drifting out of my node.
David Christian’s .284 Win F-Open Rig
Report by F-Class John
Here’s match rifle that’s as handsome as it is effective (and accurate!). In its first-ever tournament, this impressive rig took 8th place overall in F-Open at the 2019 Berger Southwest Nationals. This .284 Win hammer was wielded by David Christian, the newest member of Team Borden/Brux/Lapua. David built this .284 Winchester around a Borden BRMXD action with black PVD coating and a Jewell BR trigger. What I found fascinating is that David had built all of this before ever being approached for the team. When I asked him how that worked out, he simply said he picked the components he liked the best and knew would do the job. It was just the universe in action that he’s now on the team that matches his gear and he’s certainly not complaining that he gets to represent them now.
David uses a custom-contour 32″-long Brux 1:8.5″-twist barrel that tapers from 1.35” to 1.25” because he likes the extra stability and weight it brings. It’s all mounted in an amazingly-crafted Cerus Stock (Speedy Gonzales “Spear of Destiny” design). While Will McCloskey built the stock, it was finished to perfection by Devin Wiggett and mounted by Terry Wright of Right Rifle in Oregon. You might also notice that the buttstock features a R.A.D. recoil system which adds the final touch to the system.
Stunning Laminated Maple/Cherry/Walnut/Wenge Cerus Stock
When asked what people comment on when they see his gun, David says it’s the stock, hands down. Having handled this gun myself, I have to agree and believe me when I say the pictures don’t do it justice. The exterior forearms are torrified Maple while the core is made up of Brazilian Cherry, Walnut, and African Wenge wood. It makes for an ultra-strong stock with stunning beauty to match.
David currently tops this beauty with a Kahles K1050 10-50x56mm scope featuring the MOAK reticle. David really likes the 20 MOA per revolution dial as well as the top-mounted parallax adjustment. This is especially helpful for him as David shoots left-handed. Most scopes have a left-side parallax knob which is difficult for him to use during a match.
You can’t have a rifle this good-looking and functional without riding on the right gear. David uses a Protektor DR Bag and a SEB Special Edition NEO coaxial front rest. All told it took nearly six months to get all the parts delivered and assembled but he looks at that as a short term loss and a long term gain. Using Erik Cortina’s load development methods with Berger 180gr Hybrid Target or 184gr Hybrid Target bullets and quality Lapua brass, David has achieved some amazing results. Here’s a representative target from a recent match. That’s mighty fine shooting!
If you want to “hit the ground running” in the F-Open game, this wouldn’t be bad setup to emulate and if you see David at a match, he’s always more than happy to talk to you about it.
Amazing Accuracy from 6mmBR Tubegun
You Can’t Believe How This Gun Shoots
The day we planned to shoot prairie dogs was windy, so we headed to public land nearby and set up steel to get ballistics drop info and simply to play at distance. We had 5″ steel at 220 yards, 10″ steel (diamond) at 510 yards, and 10″ steel (square) at 650 yards. Wind was from 8 mph to just over 20 mph, so the little 123 grainer was getting tossed about, while keeping us humble all at the same time. Regardless of the gusty winds, I considered the session a success!
Great Results with Varget + 77gr Sierra TMKs
In some respects, the 7mm SAUM cartridge may be better than the 7mm WSM. The 7mm SAUM holds less powder — but that’s a good thing, since the capacity is more than adequate to do the job. You can drive the 180s at 3000 fps with a SAUM using less powder than with a WSM. Additionally, the SAUM case has a slightly longer neck. This gives you greater flexibility in bullet seating. With a long neck you can set the throat so the long 180+ graing bullets are above the neck shoulder junction, yet you can still seat shorter hunting bullets close to the lands. Additionally, long case necks, some believe, cause less throat erosion than shorter necks. That’s not “hard science” but it is certainly a view shared by many experienced shooters. The long neck is one reason many varminters favor the 6mm Remington over the .243 Winchester.
