Alliant’s Powder for 50-Caliber Applications
In 2009 Alliant unveiled Reloder 50, a new powder designed for long-range, 50-caliber rifle shooters. According to Alliant, the burn rate is “a little slower than Winchester 860″ and the powder is showing excellent lot-to-lot consistency. Load density is optimized for the 50 BMG and similar cases. Like Reloder 17, Reloder 50 employs a process which penetrates the kernels with the burn-rate-controlling chemical. This should allow a longer, flatter pressure curve, yielding more velocity than conventional powders can deliver. Alliant says that Reloder 50 offers “superior velocity and the ability to burn cleaner (with less residue).” Reloder 50 comes in both 1-lb (#150527) and 8-lb (#150528) containers.
Giraud 50 BMG Case/Bullet Comparator Giraud Tool makes a comparator for 50-Cal cartridges. The double-ended comparator is quite versatile. In one orientation you can measure base-to-ogive bullet length and also measure cartridge OAL from rim to bullet ogive. When reversed, you can use the comparator to measure cartridge headspace. The $30.00 Giraud 50 BMG Comparator gauge is constructed of 303 stainless and fits most any vernier, dial, or digital caliper. CLICK HERE for more info.
Lyman 50 BMG AccuTrimmer and Forster 50 BMG Trimmer
50 BMG enthusiasts asked for a reasonably-priced 50 BMG case trimmer and Lyman responded with an Accutrimmer designed specifically for that cartridge. Easy-to-use course and fine cut-length adjusters are positioned on the right side (by the handle). The shell head fits into a special holder which centers the case. The unit comes complete the 50-Caliber neck pilot. This case trimmer, including pilot, costs $59.99 at MidwayUSA.com.
Forster Products also makes a dedicated 50 BMG trimmer. Forster’s cutter tip is much sharper than the cutter on the Lyman AccuTrimmer. However, with the Forster tool you will pay more for that superior cutting ability — Forster’s 50 BMG trimmer costs $92.95 at Sinclair International.
Share the post "Specialized Products for 50 BMG Shooters"
The regular, monthly 600-yard benchrest match at the Piedmont Gun Club in Rutherfordton, NC rivals a National event in terms of the quality of the shooters and the rifles. And just yesterday, a pending new IBS 600-yard, four-target Light Gun Group Aggregate Record was shot. Chad Jenkins put together a stunning 1.495″ Aggregate shooting a Light Gun with Shehane Tracker stock and Krieger barrel. Chad’s smallest group was a 1.033″. The caliber was a ‘Plain Jane’ 6mmBR. Chad’s 1.495″ Agg breaks the existing 1.6068″ record set by Sam Hall in 2011.
Sam Hall reports: “Congratulations goes out to Chad Jenkins today at Piedmont Gun Range, Rutherfordton, NC. Chad shot a 1.495″ four-target aggregate in LG this morning! The old record (1.6068″) was shot by yours truly last July. That is some kind of great shooting! Chad has been shooting great and kicking our tails for two years now. You will probabbly be hearing more from him. What I know is: he was shooting 105gr Berger VLDs (with Varget and CCI Primers) in a standard 6BR, with BAT action, ST-1000 stock, and 1:8″-twist Krieger barrel. I think it is safe to say it is a ‘hummer’!”
Share the post "Chad Jenkins Sets IBS 600-Yard LG Record with 1.495″ Aggregate"
We’re excited when major barrel-makers offer new technologies that promise worthwhile performance benefits for hunters or match shooters. Lothar Walther (LW) has developed a new bi-metal barrel system that cuts weight dramatically while promising significantly-enhanced heat dissipation.
Walther’s new Ultra-Lightweight Barrels combine steel with lightweight alloys. This results in a significant weight reduction without the use of carbon fiber, epoxy binders, or other heat-retaining materials. Beginning as an LW50 stainless blank, the barrel is precision-machined to remove excess weight. An outer casing of light-weight alloys is machined and the two are fitted together without adhesives. Basically you end up with the steel inner barrel inside a larger-diameter fluted aluminum outer barrel (see diagram). This gives you the ‘best of both worlds’ — light weight for ease of carry, and thick diameter for rigidity and enhanced heat dissipation. Near the action, the barrel remains all-steel.
We haven’t tested one of these bi-metal composite barrels, but the potential for significant weight savings is obvious — aluminum is a lot lighter than steel. What’s more, a metals expert we contacted said that a bi-metal system employing fluted aluminum over steel, if assembled properly, could dissipate heat much better than steel alone (given the same diameter). Stainless steel has a thermal conductivity factor of 16. Aluminum has a thermal conductivity factor of 250.*
Our expert also pointed out that some other composite barrel systems on the market actually increase heat retention because they place insulating materials next to the inner steel barrel. (Carbon, Fiberglass, and Epoxy are all considered “insulating substances” as they have very low thermal conductivity*.) The LW system of aluminum over metal should avoid this mistake, our expert said. Lothar Walther says: “Unlike solid steel barrels, this barrel sheds heat fast. VERY FAST!”
Half the Weight of Conventional Barrels
How much weight can you save? With a 1.200″ shank diameter (except Savage) and a muzzle diameter of 0.850″, the LW Ultra-Lightweight Barrel is less than half the weight of a standard varmint barrel of the same size. Walther claims its UltraLight Barrel can be “carried for long distances and stand up to heavy firing.” This, LW says, makes these barrels “perfect… for varmint and tactical uses”.
Pre-Chambered Ultra-Lightweight Barrels Available in .22 to .338 Calibers
Lothar Walther offers Ultra-Lightweight barrels in a full range of calibers from .22LR to .338. Each Ultra-Lightweight Barrel comes complete with chamber, crown, and breech threads. These barrels are fluted by the factory. If you order a LW Ultra-Lightweight barrel, Lothar Walter provides the services of a specialist trained in building guns with these barrels. To order one of Lothar Walther’s bi-metal barrels, CLICK HERE or contact Lothar Walthar at the address below:
*Thermal conductivity is the quantity of heat transmitted through a unit thickness in a direction normal to a surface of unit area, due to a unit temperature gradient under steady state conditions. The factor values are based on this formula: W/(m.K) = 0.85984 kcal/(hr.m. °C). Here are thermal conductivty values for common materials: Aluminum, 250; Brass, 109; Steel (Carbon 1%), 45; Stainless Steel, 16; Carbon, 1.7; Brick dense, 1.3; Concrete (medium) 0.7; Epoxy, 0.35; Fiberglass, .04.
Story tip from EdLongRange. We welcome reader submissions.
Share the post "Lothar Walther UltraLight Barrels — Less Heat, Half the Weight"
Readers in the Rockies region should head to the Colorado Rifle Club (CRC) range on Saturday June 2, 2012, from 9:00 am to 4:00 pm. There you can try out a variety of Savage rifles from 17 HMR all the way up to a big magnum. All Rimfire ammo is free, and your first five (5) Centerfire rounds per gun are free (except for .338 Lapua Magnum, $5 per round). Can’t beat that. This June 2 “rifle test-ride” at CRC is part of Savage’s Arms Club Program, which lets potential rifle buyers try out target and hunting rifles, both centerfire and rimfire, at no cost.
Savage Arms provides the rifles, Nikon supplies the optics, and Hornady provides free ammo for testing. Caliber options include .17 HMR, .223 Rem, 6.5 Creedmoor, .308 Win, .300 Win Mag and .338 Lapua Magnum. (For the .338 Lapua Magnum, premium Lapua ammo is $5.00 per round). If you have not shot Savage’s F-T/R or Law Enforcement Series rifles, now is your chance. We also recommend Savage’s model 93R17 TR, a .17 HMR rimfire with the look and feel of full-size centerfire rifle. The 93R17 we tested last year was very accurate and we liked the look and feel of the matte-black tactical-style stock.
Directions to Range:
The Colorado Rifle Club range is located at 76099 East 96th Ave., Byers, CO 80103. Byers is 40 miles east of Denver on l-70 at exit 316. To get to the range, travel 8 miles east of Byers on U.S. 36, then about 9 miles north on Leader Road (52N), then one mile west on 96th Ave. to the range gate, then one mile north to the ranges. CLICK HERE for map to CRC range.
Latitude and Longitude: 39° 52′ 12.58″ N, 104° 05′ 39.47″ W
Story Tip by EdLongRange. We welcome reader submissions.
Share the post "Savage Days in Colorado (Free Gun Tests, Free Hornady Ammo)"
Sebastian Lambang, creator of the original SEB Coaxial Rest and the SEB NEO Rest, has a new product in the works. Seb has modified and upgraded his superb NEO rest, so that it can handle heavy, long-range benchrest rifles with ultra-wide forearms. Seb calls his super-sized front rest the SEB “MAX”. As you can see in the photo below, the MAX looks like a NEO but with a wider stance and more substantial rest top. Spring rates are optimized to handle rifle weights up to 45kg (99 pounds), using appropriate counterweights. Seb hopes to complete production of fifty (50) SEB MAX rests by late August 2012.
MAX Rests Use Counter-Weights to Handle Very Heavy Rifles
When configured for use with true Heavy Guns, SEB MAX rests will be supplied with adjustable counter-balance weights in load-specific sizes. For example, a 1.8-lb counter-weight is used for a 40-lb gun, a 2.3-lb counter-weight is used for a a 60-lb gun, while a 2.6-lb counter-weight is fitted for a 70-lb gun. The basic counter-weight can be augmented with additional steel sections. Seb tells us: “The basic ‘default’ counter-weight is a 1″-diameter shaft, about 7″ long. Additional 2.5″-diameter SS ‘rings’ can be fitted on the main shaft to balance the action. When people order the MAX, they must provide the weight of their gun. I will then craft the appropriate ‘rings’ in various sizes to properly balance the weight of the customer’s particular gun and thereby make the action smooth to operate.”
Watch SEB MAX Prototype Used by Stuart Elliot
In this video, Aussie Stuart Elliot uses a prototype SEB MAX with his .300 Win Mag Heavy Gun at a 1K benchrest match in Brisbane, Australia. Stuart, who runs BRT Shooters Supply, recently won the Australian 500m Fly Shoot Nationals shooting a .300 Win Mag.
New SEB MAX Rest Based on Successful NEO Rest Design
Below is the standard SEB NEO rest. The MAX is wider and will hold a rig up to 45kg. The MAX represents an evolution of the original NEO design. As anyone who has had the pleasure of using one knows, the NEO is very smooth to operate and has a huge range of vertical and horizontal travel. In addition, the NEO can be quickly dis-assembled to store flat. The new SEB MAX can likewise be dis-assembled for easier storage and transport. Photo by R.J.Hamilton.
Sebastian Lambang has a website at www.SebCoax.com, but you won’t find info on the SEB MAX there yet. If you have specific questions, send email to: sebastianlambang [at] yahoo.com.
For USA price list and to place orders, please contact:
Ernie Bishop
306 West Flying Circle Drive
Gillette, WY 82716
ernieemily [at] yahoo.com
Phone: (307) 257-7431
Share the post "New Ultra-Wide SEB MAX Front Joystick Rest Revealed"
Danny Biggs is one of the nation’s most successful F-Class shooters. A two-time (back to back) National Champion in F-TR Class, Danny also finished third in Open Class at the 2010 National Championships. Notably, Danny’s X-count of 67Xs, the highest of all competitors, was 10 Xs higher than 2010 F-Open winner Derek Rogers.
Mat with ‘Donut-Hole’ Cut-Out for Rear Bag
Danny is a very savvy competitor, to say the least, and he brought some innovative gear with him to the Nationals. Along with his height-adjustable Sinclair wide-base bipod, Danny used a cleverly modified shooting pad and Edgewood rear sandbag. Danny’s “donut-hole” mat featured a cut-out in the middle, allowing him to place his rear sandbag directly on the ground. This helps stabilize the bag no matter what the ground surface or slope. With the bag sitting directly on the ground, it’s less likely to slide or rotate.
In addition, Danny’s rear bag is raised up via a thick rubber base or “foot”. The fat base, which appeared to be hard rubber, is secured via metal tabs that clamp on to the hard leather bottom of Danny’s Edgewood rear bag. The Edgewood bag has a lip around the bottom that provides a natural attachment point for the metal tabs.
Inexpensive MidwayUSA Shooting Mat
Danny uses an affordable shooting mat — the basic 67″ L x 26.75″ W MidwayUSA shooting pad that retails for $49.99. FYI, MidwayUSA’s larger Pro Series Competition Shooting Mat is on sale right now for the same $49.99 (sale price through May 31, 2012). Sized 73.5″ long x 35.5″ wide, this deluxe, khaki-colored mat rolls up into an 8.5″ Diameter “sausage” for transport or storage. The mat has rubberized elbow and knee pads; the mat is about .535″ thick at the knee and elbow pads. By comparison, the standard MidwayUSA Shooting Mat is only 0.335″ thick on the pads. Both standard and Pro Series mats have corner grommets allowing the mat to be staked down in high winds. These mats both have a carry handle and a shoulder strap.
Share the post "Danny’s ‘Donut-Hole’ Modified Shooting Mat for F-Class"
ZCORR Products has introduced a new Anti-Corrosion Softcase with a built-in, vacuum-sealable VCI corrosion-barrier bag providing airtight and waterproof protection for firearms. The 42″-long main gun compartment houses a VCI storage bag that clips into the softcase. ZCORR’s clip-in system lets you secure a second long-gun bag when two-gun transport is needed. Double-gun capacity is a plus because these cases are expensive — MSRP is $249.00. That’s ten times the cost of some basic soft-skin (fabric and foam) rifle carriers.
ZCORR’s reinforced VCI bags are sturdy, being made from the same tough VCI material used in the popular ZCORR long-term storage bags. The clip-in VIC bags are designed to withstand frequent inserting/removing of firearms. ZCORR claims: “With repeated use, such as one to two shooting sessions per week, the VCI vacuum bag will last at least five years and longer with less use. After five to ten years of use customers can simply replace the VCI bag by unclipping it from the softcase and installing a replacement.”
While we like the idea of a soft guncase with serious built-in corrosion protection, it’s too bad that the case is only 42″ long. That size will hold ARs, and some short tactical bolt-guns, but it’s way too short for typical precision match rifles. At least the ZCORR Softcase offers additional compartments for handguns and accessories. There is an 11”x35” front compartment for handguns and magazines. Other shooting accessories can be stowed in two extra pockets measuring 9″×12” and 9″×9″ respectively.
COMMENT: For $249.00 one can get a quality, full-length hard-case and three or four 54″-long vacuum-sealable Vapor Phase Corrosion Inhibitor (VpCI) bags, big enough to hold a long match rifle with room to spare. A hard case with 54″ bags woud be a better solution for most precision rifle shooters than this first-generation ZCORR Softcase. Hopefully ZCORR will get the message that its current Anti-Corrosion Softcase is undersized (for bolt guns) and over-priced.
Share the post "New ZCORR Anti-Corrosion Softcase"
Results from a recent international air rifle competition bode well for Team USA’s prospects at the 2012 London Olympic Games. In the women’s 10m Air Rifle event, a talented trio of young American lady shooters won the team silver medal at the International Shooting Competition of Hanover (Germany). Congrats to the three Hanover Silver Medalists: Amanda Furrer (393), Emily Holsopple (389), and Amy Sowash (393).
Good luck ladies on your quest for Gold in London this summer! The Olympic Games kick off Friday, July 27, 2012. Olympic shooting matches will be held 28 July through 5 August at the Royal Artillery Barracks in Woolwich. 390 shooter-athletes will take part. Rifle events will include 10m air rifle (men, women), 50m three-position rifle (men, women), and 50m rifle prone (men only).
Share the post "American Ladies Win Silver in Pre-Olympic Air Rifle Competition"
Story based on report by Lars Dalseide for the NRA Blog
The NRA National Firearms Museum will soon showcase the historic Theodore Roosevelt collection in a major exhibit. One highlight of the upcoming exhibit will be a high-grade 1886 Winchester rifle owned and used by Roosevelt before, during, and after his presidency.
Teddy Roosevelt loved Winchester lever guns. In his book Hunting Trips of a Ranchman, Roosevelt wrote: “The Winchester stocked and sighted to suit myself is by all odds the best weapon I ever had, and I now use it almost exclusively[.]”
According to Senior Curator Phil Schreier, this Winchester was highly customized and upgraded for its famous owner. Notable custom features include Monte Carlo cheek piece, checkered pistol grip, flat metal buttstock, and deluxe color case-hardening. Given its beauty, one might doubt that President Roosevelt actually hunted with this rifle — it looks too shiny and new. There’s a reason for that — he kept sending it back.
Records show that Roosevelt’s rifle went back to the Winchester plant on five separate occasions. Each time to be refit and refinished to the President’s specifications. That’s why the rifle remains so pristine more than a century after it was crafted. For more information on this rifle and the Roosevelt Collection, tune in to Curator’s Corner on NRANews.com and Sirius/XM Patriot Satellite Radio.
Share the post "Teddy Roosevelt Guns to Be Displayed at NRA National Museum"
NOTE: This article was released in May 2012. That is over TEN YEARS AGO. The items are no longer offered with such pricing.
M1 Garand barreled receivers (item RM1SABRWB) are now available from the CMP for $350.00 plus $12.95 shipping. Combine one of these with an $82.00 walnut M1 Garand replacement stock from Boyds’ Gunstocks and you’ll have a handsome and affordable rig. (But sights, trigger group, op rod, gas system, and other key components must still be acquired.) These are Grade B receivers with “service grade” or “high quality service grade” barrels. The CMP notes that: “Receiver may have minor pitting / frosting above and below below the wood line and has been refinished. Bolt includes: extractor, extractor spring & plunger, ejector, ejector spring and firing pin.”
Share the post "CMP Now Selling M1 Garand Barreled Receivers for $350.00"
With information on over 55,000 firearms, the Firearms Guide is the most comprehensive resource on guns ever created. And now it’s bigger and better than ever. The updated 3rd Edition of the Firearms Guide is now available on DVD for $39.95 from Impressum Media.
Think of this as a digital encyclopedia of guns — the mother of all gun reference guides. The sheer amount of information is mind-boggling. The Firearms Guide covers over 55,000 models of firearms, airguns, and ammo from 500 manufacturers. Products are illustrated with 36,000 high-res color photos, plus 3,000+ schematics with parts lists for 268 gun-makers. If you’re a gunsmith or armorer, you’ll want to buy this DVD, just to have the searchable schematics with part numbers handy.
If you are a gun collector, or just an information junkie, you’ll find this DVD to be an invaluable resource. The DVD’s scope is truly worldwide, with coverage of gun makers in Western Europe, Eastern Europe, South America, South Africa and Asia as well as North America. With the DVD’s search capability you can search by gun caliber, manufacturer, and key features (e.g. “.223 Rem, Colt, folding stock”). There are 14 different search criteria — this allows you to “drill down” precisely to find the gun you want in seconds. Shown below are typical profiles of listed products:
There are some cool bonus features that significantly enhance the $39.95 DVD:
3,000+ detailed, zoomable schematics from 268 manufacturers.
500 Printable Targets: game animals, silhouettes, crosshairs, sight-ins, fun targets.
FFL Locator – Searchable database of over 62,000 gun dealers in the USA with contact info.
US-EU Ammo Caliber Chart: Cartridge equivalency charts identify the correct domestic equivalent of European ammo.
Share the post "3rd Edition of Firearms Guide DVD — Bigger and Better"
The good news continues for Sturm, Ruger & Co. (Ruger) which has seen huge gains in its stock price over that past couple of years. Ruger recently reported that first-quarter sales were up 49% compared to the same period in the previous year. That announcement has caused Ruger shares to rise over 6% just today! (Many of us now wish we’d bought some Ruger stock in 2010 — Ruger shares are trading today at 49.38, up from 16.93 two years ago.)
New products such as the Ruger 10/22 Takedown rifle, the Ruger SR22 pistol and the Ruger American Rifle are driving sales growth. Said CEO Michael Fifer, “New product introductions were a significant component of our sales growth as new product sales represented $40.8 million or 37% of sales in the first quarter of 2012.” Ruger’s results again beat Wall Street expectations. Ruger has beaten the Zacks Consensus Estimate in each of the last seven quarters.
Share the post "With 49% Increase in Q1 Sales, Ruger Stock Price Jumps"
Alliant’s Powder for 50-Caliber Applications
The regular, monthly 600-yard benchrest match at the Piedmont Gun Club in Rutherfordton, NC rivals a National event in terms of the quality of the shooters and the rifles. And just yesterday, a pending new IBS 600-yard, four-target Light Gun Group Aggregate Record was shot. Chad Jenkins put together a stunning 1.495″ Aggregate shooting a Light Gun with Shehane Tracker stock and Krieger barrel. Chad’s smallest group was a 1.033″. The caliber was a ‘Plain Jane’ 6mmBR. Chad’s 1.495″ Agg breaks the 
We haven’t tested one of these bi-metal composite barrels, but the potential for significant weight savings is obvious — aluminum is a lot lighter than steel. What’s more, a metals expert we contacted said that a bi-metal system employing fluted aluminum over steel, if assembled properly, could dissipate heat much better than steel alone (given the same diameter). Stainless steel has a 
Mat with ‘Donut-Hole’ Cut-Out for Rear Bag
ZCORR’s reinforced VCI bags are sturdy, being made from the same tough VCI material used in the popular ZCORR long-term storage bags. The clip-in VIC bags are designed to withstand frequent inserting/removing of firearms. ZCORR claims: “With repeated use, such as one to two shooting sessions per week, the VCI vacuum bag will last at least five years and longer with less use. After five to ten years of use customers can simply replace the VCI bag by unclipping it from the softcase and installing a replacement.”
Results from a recent international air rifle competition bode well for Team USA’s prospects at the 2012 London Olympic Games. In the women’s 10m Air Rifle event, a talented trio of young American lady shooters won the team silver medal at the International Shooting Competition of Hanover (Germany). Congrats to the three Hanover Silver Medalists: Amanda Furrer (393), Emily Holsopple (389), and Amy Sowash (393).
With information on over 55,000 firearms, the 
There are some cool bonus features that significantly enhance the $39.95 DVD:
The good news continues for Sturm, Ruger & Co. (Ruger) which has seen huge gains in its stock price over that past couple of years. Ruger recently reported that first-quarter sales were up 49% compared to the same period in the previous year. That announcement has caused Ruger shares to rise over 6% just today! (Many of us now wish we’d bought some Ruger stock in 2010 — Ruger shares are trading today at 49.38, up from 16.93 two years ago.)
