PMA Micro Die Adjuster — User Reports
Wouldn’t it be great if you could quickly and easily adjust shoulder bump during the full-length sizing process, without struggling to move die lock-rings by trial and error (or fiddle with shims). Well you can. The PMA Micro Die Adjuster is a brilliant little device that replaces the lock ring on your FL sizing die. It allows you to move the die up and down in precise, tiny increments. The tool has .001″ index marks, but you can easily set your die between the marks to achieve .0005″ (half-thousandth) adjustments.
The affordable PMA Micro Die Adjuster is offered in two versions, an upgraded model with a handy thumb screw for $69.95 (photo above), as well as the original with set screw for $65.95 (photo below).
To see how the PMA Micro-Die Adjuster works, watch this video by our friend Boyd Allen:
Many of our Forum members now use the PMA Micro Die Adjuster, and they give this specialty tool high praise. Here are actual reviews by Forum members and other verified tool buyers. Read more comments in this AccurateShooter Forum Thread.
PMA Micro Die Adjuster User Reviews
“No more ‘close enough’ for headspace[.] With this tool set-up it’s easy to put headspace exactly where you want it, then repeat it exactly for subsequent batches for the same cartridge.” — JohnF
“I have four of these Micro Adjuster rings and all I can say is that it works and it is repeatable. I bump my brass .0005″-.001″ and this die lock ring will do it without issue.” — TrapperT
“I size brass for four different 6.5×47 rifles (chambered with three different reamers) using a single die, set in the PMA Adjuster. I have to say… I should have bought one sooner. Adjusting it is very quick and repeatable to well under .001.” — /VH
“Great product. Shims used to drive me crazy, put a .002 in and get .0035 of change. With this if you want .0015 set it and that’s what you get.” — John B
“I’ve been using PMA’s lock ring for some time now and find it to be very easy to adjust to within .0005″ on a single piece of brass. Very quick to do as well. One thing I have found is that if you still need that half-thou adjustment I will run the brass once more at the same setting before I make that .0005″ adjustment and 50 percent of the time that does the trick. The marked increments are in .001″ scale so if you go half way in between there’s your half-thousandth.
PMA Micro-Adjuster vs. Shims: With respect to using shims, that requires you to completely remove the die. That gets old rather quickly after having used the PMA adjustable lock ring.” — Patch 700
“I like mine — adjustments are easy and it will adjust very fine. I used to use .001″ shims. Now can adjust my bump as fine as I want.” — Joe139
“The PMA adjuster works just like they say it does and is very simple to use and adjust. I use JLC inserts as well … as nice as they are you’re still hobbled by a click. However with the PMA you can go between what would be clicks. And you can use them … with any die.” — Dusty Stevens
Product Description from PMA Tool
The PMA Tool Micro Die Adjuster (MDA) replaces your existing lock ring and can be used with nearly any 7/8-14 full length sizing die. We successfully used this tool with sizing dies from Redding, RCBS, Hornady, Lee, Harrells Precision and those made from Newlon Precision die blanks. It allows you to easily make adjustments to your “shoulder bump” as fine as .0005″. The engraved marks on the MDA are equal to approximately .001 inches (true adjustment .000992″) of adjustment to the shoulder bump. Splitting the engraved marks is therefore approximately equal to .0005″. The design of the MDA does not allow it to work with the Forster Co-Ax press. Some custom dies for very short cartridges may require the use of an extended shellholder. Micro Die Adjuster shown in use installed on Custom Newlon/Scott 6mm PPC Die and Harrells Precision Compact Press.
Similar Posts:
- PMA Micro-Die Adjuster — Try One And You’ll Be Spoiled
- PMA Micro-Die Adjuster and Whidden Click-Adjustable FL Dies
- Click-Adjust FL Die Systems from PMA Tool & Whidden Gunworks
- Click-Adjust Die Options from PMA Tool and Whidden Gunworks
- Forster Accu-Ring — Laser-Marked Die Lock Ring
Tags: Bump, Case Sizing, Die, FL Sizing, Micro Adjuster, PMA Tool, Reloading, Shoulder Bump
Nice. Was getting excited until I saw the comment about not able to be used in a Forster press. Suppose I have to continue with a marker pen.
Nice option for someone using several different dies.
Well, I’ll throw in my .02. I bought one of these to switch between all of my non micro top dies to effectively make them micro tops. That part works great.
I then discovered that once finding the sweet spot for bumping shoulders, you REALLY don’t want to move it to a different die and start over.
Since these have spoiled me so much, I refuse to go without one and have bought several more since.
In my opinion, to buy a non micro top die, then buy the lock ring, you’re better off just buying a micro top die. However, if you already have non micro top dies, this is a no brainer! Buy one for every sizer and seater that you have! You’ll thank me later.
This is the only time i have not been 1000% happy with the forester press
When are you making one that suits forester presses ?
Tim