When you make a reloading mistake, you may need to “pull down” assembled ammo. The embedded UltimateReloader.com video demonstrates how to use the Hornady Cam-Lock bullet pulling system.
When Reloading Goes Bad — The Danger of Over-Charging
Our friend Gavin Gear of UltimateReloader.com was recently reloading some 9mm pistol ammo with his Hornady progressive press. As part of his reloading procedure, he visually checks the cases — and he noticed that the charges seemed high. Sure enough, his most recently-produced rounds were about two grains over spec. He diagnosed the issue: “I was using a powder measure without a baffle. What happened was, over the course of the loading session, things settled in, and the charge level increased.”
Not knowing just when his powder measure started delivering too much powder, Gavin decided, for safety’s sake, to pull down all the ammo he had just reloaded. Yes that’s time-consuming, but it’s better than the alternative — having a dangerous Kaboom while shooting. With fast-burning pistol powders, a two-grain over-charge could cause a blown case, damaged firearm, and/or serious injury.
Watch Cam-Lock Bullet Puller Used to Remove Bullets from Loaded Ammo:
Use of Bullet Puller starts 4:00 minutes into video.
Gavin says it is vitally important to perform safety checks during the reloading process: “You’ve got to do it — check every single round to make sure there IS powder, and that there’s not too MUCH powder. Double, Triple, Quadruple check your components… and your powder charges. You can’t be too careful.”
To pull down a loaded round, first place the cartridge in the shellholder on your press ram. Then raise the round up into the bullet puller device installed where a die would go. The Hornady Cam-lock bullet puller works by clamping the bullet in a collet when you flip down the red-coated lever. Then, with the case held by the rim in the shell-holder, the bullet exits the cartridge as the press ram is lowered. It takes time, but it’s pretty fool-proof once you get the hang of it. This entire process is illustrated in Gavin’s video, starting near the four-minute mark.
The Hornady Cam Lock Bullet Puller has four (4) key components: 1. Cam-Lock die body; 2. Cam-Lock lever; 3. Stem; and 4. Collet (Caliber-specific).
NOTE: In order to use this tool, you’ll need the appropriate collet for each diameter range of bullets you intend to pull. For example use collet #3 for 6mm, collect #6 for 7mm, and collet #7 for .308 Caliber.
Share the post "Pulling Bullets Safely and Efficiently with a Collet Puller"
The 2018 CMP competition rules are now approved and posted on the CMP website. The 2018 CMP Highpower Rifle and Pistol Competition Rules and the 2018 CMP Games Rifle and Pistol Competition Rules can be downloaded on the CMP Competition Rules Page.
Evolution of CMP Competition Rules
There are a number of important CMP Rule changes for 2018 that are spelled out below. CMP Competition Rules have undergone major changes in the last few years that were aimed at modernizing the CMP competition program and promoting greater participation in rifle and pistol target shooting. In 2015, rule changes expanded the types of pistols that can be used in EIC and National Match Service Pistol events and introduced the immediately popular CMP 22 Rimfire Pistol Distinguished program. The most significant 2016 change was the authorization for Service Rifle shooters to use optical sights with 4.5X max magnification. 2017 saw the introduction of a new classification system, rules for electronic targets and the addition of rules for “Alternative Rifles” and “Match Rifles”.
Important Rules Changes for 2018
The biggest change in the 2018 Rules is the introduction of a two-track system for conducting CMP-sanctioned Highpower Rifle Matches. Highpower Rifle events can now be conducted as either traditional “National Trophy Rifle Events” where there are no sighting shots and competitors start rapid-fire series from standing or as “CMP Cup Match Events” where sighting shots are allowed before each stage and competitors start rapid-fire series in position. All EIC Rifle Matches and Camp Perry National Trophy Matches will continue to be conducted according to National Trophy rules, with no sighters and rapid-fire starting from standing. The CMP Cup Matches, which are scheduled at the beginning of the 2018 CMP Highpower Rifle Matches at Camp Perry on 23-25 July, and the CMP Cup Matches, which are included in the 2018 CMP Travel Games programs, will be conducted under Cup Match rules with sighters and rapid-fire stages starting in position.
The rules for CMP As-Issued Military Rifle and Pistol events and Rimfire Sporter Matches remain unchanged in this regard. These events typically allow sighters at the beginning of each course of fire. Competitors start rapid-fire series from standing, but any competitors who are 70 or over or who have physical limitations that prevent them from readily standing and getting back into position are allowed to start rapid-fire series in position.
Otherwise the 2018 CMP Games Rifle and Pistol Rules, which include Rimfire Sporter Rifle Rules, have only minor changes from the 2017 edition.
National Records — Rules providing for the official recognition of National Records in open and junior categories in CMP-recognized events were added for 2018. The CMP is compiling its first list of official records and will post it on the CMP website as soon as it is ready. To be recognized as National Records, scores must be fired in the National Matches or in competitions conducted by the CMP staff such as CMP Travel Games or National Range Matches.
CMP Smallbore Matches Coming to Camp Perry
Traditional smallbore rifle championships are returning to Camp Perry in 2018 and rules for those events are being drafted now. The 2018 National Matches Calendar features six days of CMP Smallbore Rifle shooting on 17-22 July. There will be two days of smallbore position and four days of smallbore prone shooting, along with one full day of Rimfire Sporter Rifle competition on 22 July. Provisional CMP Smallbore Rifle Rules will be released in the next few weeks.
Electronic Targets — A new section has been added to the CMP Rulebooks to help explain and clarify the CMP’s Electronic Scoring Target Rules. See Rule 7.0 in the CMP Competition Highpower Rifle and Pistol Competition Rules or Rule 9.0 in the CMP Games Rifle and Pistol Competition Rules.
Tired of hauling around an old-fashioned Score Book and making entries with pencil and paper? Well now you can go digital — Creedmoor Sports has released a full-featured Scoring Book App that lets you plot your shot locations using an iPhone, iPod, or iPad (Apple tablet). The price is right — just visit the iTunes store to download the App for FREE.
Record Match and Practice Data
This new App, available for free in the Apple App Store, and the Google Play Store provides all the same functions and capabilities of the traditional Creedmoor print Data Book, but with the convenience and ease of recording your match and practice information with your iPhone or tablet. With this App you can break your 20 shot slow-fire segments into either 10- or 20-shot targets, and also opt for sighting shots. All the specific event data can also be recorded, such as location, wind, light etc., along with wind and elevation adjustments.
COMMUNICATIONS Restrictions: In some matches you are not allowed to have electronic communication ability, so you may have to set your iPhone to “Airplane Mode”, or use this only with an iPod (which does not have two-way communication capability).
Share the post "FREE Creedmoor Scoring Book App for iOS and Android"
Does your Black Rifle have a sloppy upper/lower fit? That can be annoying; what’s more, loose fit can limit accuracy potential. Here’s a clever solution for poor-fitting AR-15 and AR-10 upper and lower receivers. The new JP MicroFit takedown pins can improve even the sloppiest ARs, providing a rock-solid upper/lower receiver fit.
MicroFit pins come in three sizes and two types: standard (“mean”), oversized, and undersized, with types for both front and rear of the receivers. The mean pins match standard takedown pin sizes while the over- and under-sized vary by slightly more than .001″ (+/-) from the standard diameter. NOTE: Although most poor-fitting receivers are loose, some are too tight. Very tight receivers, such as post-Cerakote, can be remedied with the undersized pins.
Shown is JP Enterprises’ PSC-12™ upper assembly with LRP-07™ lower assembly.
“An AR with a loose upper/lower receiver… will not reach its accuracy potential. That was the goal with our original JP Tension Pin, but MicroFit™ pins provide the same result without tool-assisted takedown. The MicroFit pins require no modification to the receiver. They simply replace your current pins”, stated JP Enterprises founder John Paul.
JP’s MicroFit pins feature a polished black finish with a hard, durable QPQ coating. This provides smooth insertion/removal plus excellent corrosion resistance. All pins feature a two-faceted punch or bullet capturing recess. This allows the user to apply force to the pins safely without risking scratching the receiver. JP’s MicroFit pins are sold as both as individual pins and as replacement sets.
Share the post "JP MicroFit Takedown Pins for AR15s and AR10s"
In our Shooters’ Forum, there was an discussion about a range that was threatened with closure because rifle over-shoots were hitting a farm building over two miles from the firing line. One reader was skeptical of this, asking “how’s that possible — were these guys aiming at the stars?” Actually, you may be surprised. It doesn’t take much up-angle on a rifle to have a bullet land miles down-range. That’s why it’s so important that hunters and target shooters always orient their barrels in a safe direction (and angle). Shooters may not realize how much a small tilt of the barrel (above horizontal) can alter a bullet’s trajectory.
How many degrees of muzzle elevation do you think it would take to hit a barn at 3000 yards? Ten Degrees? Twenty Degrees? Actually the answer is much less — for a typical hunting cartridge, five to seven degrees of up-angle on the rifle is enough to create a trajectory that will have your bullet impacting at 3000 yards — that’s 1.7 miles away!
Five degrees isn’t much at all. Look at the diagram above. The angle actually displayed for the up-tilted rifle is a true 5.07 degrees (above horizontal). Using JBM Ballistics, we calculated 5.07° as the angle that would produce a 3000-yard impact with a 185gr .30-caliber bullet launched at 2850 fps MV. That would be a moderate “book load” for a .300 Win Mag deer rifle.
Here’s how we derived the angle value. Using Litz-derived BCs for a 185gr Berger Hunting VLD launched at 2850 fps, the drop at 3000 yards is 304.1 MOA (Minutes of Angle), assuming a 100-yard zero. This was calculated using a G7 BC with the JBM Ballistics Program. There are 60 MOA for each 1 degree of Angle. Thus, 304.1 MOA equals 5.068 degrees. So, that means that if you tilt up your muzzle just slightly over five degrees, your 185gr bullet (2850 fps MV) will impact 3000 yards down-range.
Figuring Trajectories with Different Bullets and MVs
If the bullet travels slower, or if you shoot a bullet with a lower BC, the angle elevation required for a 3000-yard impact goes up, but the principle is the same. Let’s say you have a 168gr HPBT MatchKing launched at 2750 fps MV from a .308 Winchester. (That’s a typical tactical load.) With a 100-yard zero, the total drop is 440.1 MOA, or 7.335 degrees. That’s more up-tilt than our example above, but seven degrees is still not that much, when you consider how a rifle might be handled during a negligent discharge. Think about a hunter getting into position for a prone shot. If careless, he could easily touch off the trigger with a muzzle up-angle of 10 degrees or more. Even when shooting from the bench, there is the possibility of discharging a rifle before the gun is leveled, sending the shot over the berm and, potentially, thousands of yards down-range.
Hopefully this article has shown folks that a very small amount of barrel elevation can make a huge difference in your bullet’s trajectory, and where it eventually lands. Nobody wants to put holes in a distant neighbor’s house, or worse yet, have the shot cause injury. Let’s go back to our original example of a 185gr bullet with a MV of 2850 fps. According to JBM, this projectile will still be traveling 687 fps at 3000 yards, with 193.7 ft/lbs of retained energy at that distance. That’s more than enough energy to be deadly.
Share the post "5 Degrees of Doom — The Danger of Over-Shooting the Berm"
RCBS has announced the successor to the venerable RCBS Trim Mate. The New-for-2018 RCBS Brass Boss features six rotating stations that handle all your brass neck-brushing, chamfering, deburring, and pocket uniforming chores. The new Brass Boss includes tools for all six stations: inside VLD chamfering tool, outside deburring tool, primer pocket cleaners (small/large), military crimp removers (small/large), primer pocket uniformers (small/large), case neck brushes (four diameters), and a tub of dry case neck lubricant. MSRP for the Brass Boss, RCBS SKU 90390, is $189.95. We expect “street price” to be around $155.00.
This machine has two different rotation speeds for the toolheads. Four stations run at 350 rpm, while the two other stations run 57% faster, at 550 rpm. That give you a choice of spin speeds. You can work fast for tougher chores like military crimp removal, and slow down for inside-neck chamfering, which should be done carefully.
Larger and taller than the older RCBS Trim Mate, the new Brass Boss has one more station (six vs. five), plus a more powerful motor. This should make the Brass Boxx more competitive with the popular Lyman Case Prep Express.
Share the post "RCBS Has New Brass Work Station with Six Powered Toolheads"
Want to learn long-range benchrest skills from the best in the business? Then head to Williamsport, PA this June. The registration period for the 2018 PA 1000 Yard Benchrest School is now open. This year’s session will be held Saturday and Sunday, June 16-17, 2018, with a “Meet and Greet” on Friday Night. Classes, taught by top 1K shooters, are held at the Original Pennsylvania 1000-Yard Benchrest Club Range, one of the best 1000-yard ranges in the country. The school will be limited to 25-30 students with one instructor for every two students.
Praise from a 1K Benchrest School Grad
Here’s a testimonial from a recent graduate: “I can attest to the knowledge that you gain. I went last year and loved it. Have renewed my membership in the Club and would love to go this year. I would love to take the course again. In the photo above I am in the back row, fourth from the right — sunglasses and blue shirt.” — Bob, Class of 2016
Participants will learn all aspects of long-range benchrest shooting from some of the most skilled marksmen in the country. Much time is spent at the loading bench and on the firing line. Classes cover load development, precision reloading, bench skills, and target analysis. You don’t even need guns and ammo — all equipment and ammunition will be provided.
School instructors tell us: “This year’s benchrest school will be a 2-day weekend event. (There is also an optional ‘Meet and Greet’ gathering Friday evening). The school is a beginner class designed to teach the fundamental skills needed to be competitive at at 600 and 1000 yards. Saturday will be spent in class covering a range of topics including reloading ‘dos and don’ts’, load development and equipment handling. Sunday we will shoot an actual match to see what you’ve learned.”
Cost for the class is $425.00 including lunches on Sat/Sun and dinner on Saturday. Act soon if you want to attend the 2018 school — the school fills quickly. NOTE: To secure your placement, payment must be made in full prior to May 25th, 2018.
Watch Williamsport Benchrest School Slideshow: Please enable Javascript and Flash to view this VideoPress video.
This slideshow was produced by Sebastian Reist an alumnus of the 2009 Williamsport 1000-yard BR school. SEE: www.sreistphotography.com.
Share the post "Williamsport Benchrest School 2018 Registration Opens"
If you want smoother bullet seating, inside neck lube can help. Forum member Ackleyman II likes to add a little Mica powder inside his case necks before seating bullets. This is easily done with the Forster three-brush neck lube kit. Ackleyman tells us: “Many loads that I have will not shoot well with a dry neck compared to a neck that is cleaned and lubed with this [Forster Dry Lubricator] — the best $15 you have ever spent.”
The Forster Case Neck Lubricator features three brushes attached to a tough, impact-resistant case with holes for bench mounting. The brushes accommodate all calibers from 22 to 35 caliber. The kit includes enough “motor mica” to process 2000 to 3000 cases and has a cover to keep dust and grit from contaminating the mica. By moving the case neck up and down on the correct mica-covered brush, the neck can be cleaned and lubricated at the same time.
Function: Lubricate case necks for easier resizing
Contents: Kit with base, lid, and three nylon brushes
Lubricant: Includes 1/10 oz. of Motor Mica, enough to process 2000-3000 cases
Share the post "For Smoother Bullet Seating — Try Dry Lube Inside Case Necks"
Savage Arms will launch more than two dozen new products at the 2018 SHOT Show, January 23-26 at the Sands Expo Center in Las Vegas, Nevada. The big news is the AccuFit stock system for the Model 110 rifle line. “Our new AccuFit System is designed to allow shooters to quickly adjust comb height and length-of-pull for a customized fit. This results in more consistent, more comfortable shooting”, says Beth Shimanski, Savage Senior Marketing Manager. These new Savages also feature the Accustock internal chassis with bedding block (see second video below).
AccuFit Adjustment System
Accustock Embedded Chassis System
CLICK HERE for more videos showing new Savage Design and Engineering features.
More Chambering Options for Savage AR-Platform Rifles
Savage has added new chamberings for its MSR black rifle line-up. MSR 15 models will be newly offered in 224 Valkyrie, 22 Nosler, and 6.8 SPC. A 6mm Creedmoor version of the AR-10 platform MSR 10 Long Range has been added, and Savage will offer the hard-hitting .338 Federal chambering in the MSR Hunter rifle (along with 6.5 Creedmoor and .308 Win).
Savage 2018 New Product Highlights
Model 110 Storm with AccuFit: Features stainless steel action and barrel for adverse weather and conditions. Sixteen caliber and left-hand options.
Model 110 Long Range Hunter with AccuFit: Engineered for long-range shooting with a 26-inch barrel and muzzle brake. Nine caliber options, including 338 Lapua Magnum.
Model 110 Lightweight Storm: Easier to carry in field thanks to a lightweight stainless steel barrel and action. Length-of-pull is easily customized. Six caliber options.
AXIS II XP with New Stock: Popular package rifle with redesigned, ergonomic stock and Bushnell Banner 3-9×40 scope in full-size and compact models. Twenty caliber/configuration options.
MSR 15 Valkyrie: MSR 15 AR-type rifle chambered for the 224 Valkyrie. This new model features an adjustable gas block, furniture upgrades, and Elite Series Flat Dark Earth Cerakote finish.
MSR 15 Recon Long Range Precision: Equipped with alternate furniture options and chambered in all-new 224 Valkyrie, 22 Nosler, and 6.8 SPC.
MSR 10 Long Range in 6mm Creedmoor: AR-10 platform rifle design for long-range precision shooting. Chambered for the flat-shooting, modest-recoil 6mm Creedmoor cartridge.
MSR 10 Hunter in 338 Federal: Built specifically for hunters and chambered in the popular, hard-hitting .338 Federal.
B Series Compact and Left-hand: Extremely accurate bolt-action .22 LR, .22 WMR, and .17 HMR options. Now available in compact and left-hand models.
A Series Pro Varmint: Semi-automatic options in .22 LR, .22 WMR and .17 HMR, all with Boyd’s Pro Varmint stock and 22-inch fluted, heavy barrel.
All of these new rifles, as well as more bolt-action and semi-auto centerfire and rimfire rifles, will be on display at SHOT Show Booth No. 14551. Most will be set up so visitors can handle the rifle and work trigger and bolt. To learn more about the new Savage rifles and their features, visit www.SavageArms.com.
Savage MSR 10 Long Range (6mm Creedmoor, 6.5 Creedmoor, .308 Win)
Share the post "Savage New Products — Adjustable Stocks, More Chamberings"
Need a portable, light-weight target stand? Here’s a clever, minimalist alternative to big, bulky wood-framed or PVC pipe target stands. Those big frames will work, but they take up lots of space in your vehicle and, unless you build a very solid base, they tend to rock back and forth, or even blow over in high winds. With a commercial sign frame (the kind used for real estate signs) you can easily mount cardboard shooting targets.
For under $20.00 you can get a metal sign frame that can be staked directly in the ground. These sign frames, commonly used for real estate signs, are secure in high winds, and they are just about ideal if you need a simple target for zeroing during a varmint hunt. With most of these frames you can secure a cardboard target backer with zip ties or threaded fasteners. With some frames you just slide the cardboard backer into slots, so no fasteners are required. The most common “Empire-style” sign frame has a rectangular section at the top with two pointed ends about 10″ apart at the bottom. Put your foot on the crossbar to drive the frame into the ground. An angle-iron, Empire-style frame (no fasteners required) is offered by the fastrealestatesigns.com for $19.99.
Inexpensive Reinforced-Plastic Sign Frames
Shown at right is a plastic sign frame that requires no fasteners. Simply cut your cardboard target backer to 24″ (w) x 18″ (h) and slide it in from the top. Then stick the frame into the ground using the foot-slot near the bottom. These fiberglass-reinforced plastic sign frames are light yet surprisingly strong. They are also very inexpensive. The sign-holder at right costs $11.95 from Yardsigns.org. There is also an open top model ($10.95). And for $25.70 your can even get FIVE larger 25″-wide polyethylene sign frames that have hammer posts and foot-push tabs. Available in black or white, these are shown below. Buy a set of five, keep a couple, and give the other three to your buddies.
TIP: Sign Frames Are Not Ideal For All Terrain
If you shoot where the ground is very hard or rocky, these stake-in-the-ground frames may not work so well. They need to be seated firmly in the soil. But if you shoot in an area with soft soil or grassy turf, these frames can be a handy solution. Simple, light-weight and easy to set-up, they make a nice “field expedient” target holder.
Share the post "Hold Your Targets with Low-Cost Commercial Sign Frames"
At the request of our readers, we provide select “Deals of the Week”. Every Monday morning we offer our Best Bargain selections. Here are some of the best deals on firearms, hardware, reloading components, optics, and shooting accessories. Be aware that sale prices are subject to change, and once clearance inventory is sold, it’s gone for good. You snooze you lose.
Q: How Good Are These Deals? A: The Savings Are Significant — Get Some Items at Half Price.
Here are two examples. Last week we featured a MidwayUSA Pro Series Shooting Mat at $29.99. The same mat is priced now at $59.99, DOUBLE our Deals price. Likewise, late last year we featured the RCBS Rock Chucker Supreme Reloading Kit for $224.99 after Rebate. That deal sold out and now you’d have to pay $297.69, nearly one-third more! We work hard to find these deals, with savings of 25-50%. Save hundreds of dollars on firearms and big-ticket items.
1. Sportsman’s Guide — Stevens 320 12 GA Shotgun, $179.99
Every ranch, farm, or household can use a defensive 12 Gauge shotgun. We like ghost ring sights on our self-defense scatterguns, and this Stevens 320 Security model has that feature. This shotgun is a steal — get one now for the amazingly low price of $179.99 ($170.99 Buyer’s Club price). You won’t find a quality, American-made, ghost-ring 12 gauge pump for less money. At this price you can afford to buy two or three. This Stevens 320 Security shotgun is made by Savage Arms.
2. Natchez — Up to 63% Off Popular Riflescopes
Natchez is slashing prices on many popular scopes, including the 46x48mm side-focus Weaver favored by many benchrest competitors. The savings are impressive. That 46X Weaver is marked down 63%, while the Weaver 6-24x42mm Classic is 60% off. If you need a fixed-power comp scope or a reliable medium-magnification zoom scope for a varmint rifle, check out these deals. You could pay twice as much and not get better optics. There are also big savings on Nikon and Leupold Scopes.
3. EuroOptic — Sako 85 $1098.00 ($900 Off)
Sako 85 rifles enjoy a reputation for outstanding quality, reliability, and ergonomics. The Sako 85 is a top-tier rifle prized by hunters. Now you can get a handsome, wood-stocked Sako 85 for just $1098.00 — a huge $900.00 savings off the normal price. Chambered in 7mm-08, this “Bavarian” model features a traditional curved-comb stock with nice checkering on grip and fore-arm. This stock shape is quick to mount and works well from a variety of positions in the field. The Bavarian model also comes with back-up iron sights. This is a very nice hunting rig for fans of traditional wood stocks.
Here’s a really good deal on a handy reloading product, the Case Prep Trio. This versatile device features three powered heads and ships with both Inside Chamferer and Outside Chamferer tools. You can add optional accessories such as large/small primer pocket cleaners, primer pocket reamer, case neck brushes, and other 8-32 threaded tools. This $79.99 deal at Natchez is the best price we’ve found (the unit normally sells for $102.00 or more). Plus, this qualifies Hornady’s Get Loaded Promo. But the Case Prep Trio and you get 100 FREE Hornady Bullets. If you figure those 100 bullets are worth thirty dollars or so, that brings your net cost for the Case Prep Trio to around fifty bucks. We have this tool and it definitively saves time and reduces hand fatigue. NOTE: Be sure you follow ALL the directions when submitting your FREE Bullets claim! You MUST submit a sales receipt. You MUST submit the package UPC. And you MUST submit a $6.95 check for shipping. If you don’t pay $6.95 for shipping you won’t get your bullets. Got that?
5. Sportsman’s Guide — Kahr CW9 Pistol, $249.99
This pistol is an excellent carry gun. It weighs just 15 ounces and is 5.9″ overall. The gun is thin and the controls are well recessed so this Kahr is great for discrete carry — it “prints” less than most of the other guns featured here. The striker-fired Kahr CW9 has a nice trigger pull. Take-up is pretty long, but the engagement is smooth without the hitches/spikes you feel on a Glock trigger pull. Many shooters find they can shoot the Kahr more accurately that a similar-sized Glock due to the smoother trigger. The Kahr CW9 is on sale now at Sportsman’s Guide for just $249.99, or $237.49 Member price. SPECS: DAO, 5.9″ OAL, 0.90″ width, 15 oz. weight.
6. MidwayUSA — Norma .22LR Match-22 Ammo 500 Rds $39.99
This Norma Match-22 ammunition is good stuff. In many rifles it shoots as well as $8/box products from other makers. But now you can get Match-22 for the equivalent of $4 per 50-ct box when you buy 500 rounds. MidwayUSA is selling a 500-round case of Norma Match-22 for just $39.99. That works out to just 8 cents per round. We think you’ll be happy with this ammo. It is a good choice for tactical cross-training and fun shooting.
7. Amazon — Jialitte Scope Bubble Level, $10.69
If you shoot long range, you need a scope level. This nicely designed Jialitte Scope Bubble Level is fully CNC-machined to close tolerances for a good fit. It features a 30mm milled inside diameter, plus an inner insert ring so it will also fit 1″-diameter main tubes — that dual-diameter versatility is a nice feature. We also like the way the unit is nicely radiused, and has a low profile in the middle. User reviews have been very positive. You could easily pay $35.00 or more for a 30mm scope level. Purchasers have praised this product: 89% of verified buyers rated this five stars.
You don’t need to spend big bucks for an effective spotting scope to view mirage. You can get the Kowa TSN-501 Angled Spotting Scope is listed at $349.00 from B&H Photo. But, you can actually buy this Spotter for $299.00 — B&H just can’t advertise it that low. They list $349.00 but you get another $50 discount when you put it in the shopping cart: SEE REAL PRICE HERE. That’s a heck of a deal. This is a super-compact scope with 50mm objective and built-in 20-40X eyepiece. Though relatively new, the small, light-weight TSN-501 can perform basic spotting tasks effectively. This doesn’t have the resolution of the $1500+ spotters but this is fine for viewing mirage and shot markers. Put the money you save into barrels and bullets.
9. Bruno Shooters Supply — BAT Actions on Sale
This week, Bruno Shooters Supply is offering significant discounts on In-Stock BAT Machine Actions. Dozens of actions are available right now — no waiting. NOTE: All listed BAT action prices are for check or money order purchase. BAT actions put on a credit card will incur an additional 4% service fee. Additional $40.00 for shipping per action, which can only be shipped to a FFL dealer.
10. Amazon — Top-Rated 43-lb Magnetic Gun Mount, $14.95
This heavy-duty Stamaks Magnet is rated to support a full 43 pounds. That means it can actually hold a shotgun or rifle on a gun cabinet door. For the typical handgun installation, it’s even more secure. An “Amazon Choice”, this magnet has earn 98% Five-Star reviews from customers who say the magnets are powerful and the rubber case is very durable. The magnet installs with four screws. Actual review: “Really good quality! Magnet is an extremely durable and strong. Easy to install, highly recommended.” Very slim, this is a good choice for stowing a handgun in a vehicle interior or under a countertop. NOTE: Before placing in a vehicle, review your state’s laws regarding gun transport. The manufacturer states: “Stamaks Gun Magnet will easily hold an object weighing up to 43 lbs of pulling force.”
Share the post "Bargain Finder 121: AccurateShooter’s Deals of the Week"
Shooting ranges have gone upscale with the development of the “Guntry Club”. This new kind of recreational/social facility combines a shooting range with Country Club style amenities. Imagine a high-tech indoor range with “Pro Shop”, restaurant, and maybe outdoor shooting facilities as well. In the past five years, more and more of these deluxe “Guntry Clubs” have opened nationwide.
This week GunVenture TV takes a look at some of the country’s finest gun clubs. First, join Tom Gresham and RECOIL Magazine’s Iain Harrison at one of the original “Guntry Clubs” — the Scottsdale Gun Club. You’ll tour the exclusive Titanium lounge before heading to the range for some full-auto fun with Sig Sauer’s John Hollister. Then, Tom visits a very high-end facility in Centennial, Colorado. The upscale Centennial Gun Club features a retail store, range, training center, and lounge.
Finally, GunVenture visits the Talladega Super-Speedway, where Ryan Gresham takes a lap on the famous track before visiting at the CMP’s impressive new Talladega Marksmanship Park, which boasts state-of-the-art electronic targets.
Here’s a CBS News report on upscale “Guntry Clubs”, luxurious facilities that target younger, more affluent patrons. Chip Reid reports on a high-end gun club in Manassas, Virginia: “This is not your Grandfather’s shooting range. Elite Shooting Sports is 65000 Square feet of bright lights, polished wood, flat-screen TVs, and state of the art equipment”.
Share the post "Guntry Clubs — Posh, Upscale Facilities for Gun Aficionados"