Have inflation (and supply chain shortages) affected the price of powder? You bet. Probably WAY more than you could imagine. Forum member “Two Time HM LR” posted this interesting photo (above) showing Hodgdon powder prices from 1978, as sold by O.K. Weber in Oregon.
Now the prices — $20 to $44 — may not get your attention at first. But take note that these numbers are for EIGHT pound jugs. Yep eight-pounders were all under $45! For example, H4895 was $44 for 8 pounds back in 1978, 45 years ago. And H335 was $20 for eight pounds — that’s just $2.50 per pound!
These days a single pound of a desirable powder such as H4831 might cost $65 at some stores IF you can find it at all. On Hodgdon’s web site, H4831 powder is priced at $62.99 per pound in May 2025. Using that current $62.99/lb figure, H4831 is now over ELEVEN times higher than it was in 1978, when H4831 cost $44 for 8 pounds, i.e. $5.50 per pound.
Here are some comments from our Forum Members:
“Heck those prices are just about the same as current ones, just a little smaller container now.” — Joe
“I’ve got some H4831 in a can marked ‘WWII Surplus Powder’ with a price tag of $2.75. We’ll never see that again either.” Rick in Oregon
“1978 prices and [2025] income would be nice. Unfortunately that doesn’t work. If you compare prices and income, powder cost about the same. You also have to discount the temporary gouging that we are seeing.” — Tmwinds
“So I used to buy gas for 10 cents per gallon and they’d pump it, check the oil, and clean the windshield.” — Pirate Ammo
One comment suggests that the powder price hike actually tracks general U.S. currency inflation over the last four decades. So perhaps powder price increases are not as bad as they seem, when compared to how all prices have risen since 1978:
“Using H4895 [8 lbs.] as a comparison basis at $58.50 (list price) in 1978 calculates it to $287 in today’s money. Looking at … prices it looks like [8 lbs. of H4895 would cost $430] for the same item in today’s money [at Powder Valley], so it really hasn’t gone up [that much as corrected for inflation]. Availability is another issue though[.]” — Drover
Efficient cartridges make excellent use of their available powder and case/bore capacity. They yield good ballistic performance with relatively little recoil and throat erosion.
Cartridge Efficiency: A Primer (pun intended!)by USAMU Staff
The U.S. Army Marksmanship Unit (USAMU) published a series of reloading articles on its Facebook Page. In this article, the USAMU discusses cartridge case efficiency and its benefits. While this is oriented primarily toward NRA High Power Rifle and Long Range (1000-yard) competition, these factors also apply to medium/big game hunters. Assuming one’s rifle and ammunition are accurate, key considerations include ballistic performance (i.e., resistance to wind effects, plus trajectory), recoil, and throat erosion/barrel life.
Efficient cartridges make excellent use of their available powder and case/bore capacity. They yield good ballistic performance with relatively little recoil and throat erosion. A classic example in the author’s experience involved a featherweight 7x57mm hunting/silhouette rifle. When loaded to modern-rifle pressures, just 43-44 grains of powder pushed a 139gr bullet at 2900 fps from its 22″ barrel. Recoil in this light rifle was mild; it was very easy to shoot well, and its performance was superb.
An acquaintance chose a “do everything” 7mm Remington Magnum for use on medium game at short ranges. A larger, heavier rifle, it used ~65 grains of powder to achieve ~3200 fps with similar bullets — from its 26″ barrel. Recoil was higher, and he was sensitive to it, which hampered his shooting ability.
Similarly efficient calibers include the 6mm BR [Norma], and others. Today’s highly-efficient calibers, such as 6mm BR and a host of newer developments might use 28-30 grains of powder to launch a 105-107gr match bullet at speeds approaching the .243 Winchester. The .243 Win needs 40-45 grain charges at the same velocity.
Champion-level Long Range shooters need every ballistic edge feasible. They compete at a level where 1″ more or less drift in a wind change could make the difference between winning and losing. Shooters recognized this early on — the then-new .300 H&H Magnum quickly supplanted the .30-06 at the Wimbledon winner’s circle in the early days.
The .300 Winchester Magnum became popular, but its 190-220gr bullets had their work cut out for them once the 6.5-284 and its streamlined 140-142gr bullets arrived on the scene. The 6.5-284 gives superb accuracy and wind performance with about half the recoil of the big .30 magnums – albeit it is a known barrel-burner.
Currently, the 7mm Remington Short Action Ultra-Magnum (aka 7mm RSAUM), is giving stellar accuracy with cutting-edge, ~180 grain bullets, powder charges in the mid-50 grain range and velocities about 2800+ fps in long barrels. Beyond pure efficiency, the RSAUM’s modern, “short and fat” design helps ensure fine accuracy relative to older, longer cartridge designs of similar performance.
Recent design advances are yielding bullets with here-to-fore unheard-of ballistic efficiency; depending on the cartridge, they can make or break ones decision. Ballistic coefficients (“BC” — a numerical expression of a bullet’s ballistic efficiency) are soaring to new heights, and there are many exciting new avenues to explore.
The ideal choice [involves a] balancing act between bullet BCs, case capacity, velocity, barrel life, and recoil. But, as with new-car decisions, choosing can be half the fun!
Factors to Consider When Evaluating Cartridges
For competitive shooters… pristine accuracy and ballistic performance in the wind are critical. Flat trajectory benefits the hunter who may shoot at long, unknown distances (nowadays, range-finders help). However, this is of much less importance to competitors firing at known distances.
Recoil is an issue, particularly when one fires long strings during competition, and/or multiple strings in a day. Its effects are cumulative; cartridges with medium/heavy recoil can lead to shooter fatigue, disturbance of the shooting position and lower scores.
For hunters, who may only fire a few shots a year, recoil that does not induce flinching during sight-in, practice and hunting is a deciding factor. Depending on their game and ranges, etc., they may accept more recoil than the high-volume High Power or Long Range competitor.
Likewise, throat erosion/barrel life is important to competitive shooters, who fire thousands of rounds in practice and matches, vs. the medium/big game hunter. A cartridge that performs well ballistically with great accuracy, has long barrel life and low recoil is the competitive shooter’s ideal. For the hunter, other factors may weigh more heavily.
Cartridge Efficiency and Energy — Another Perspective
Former Lapua staffer Kevin Thomas explains that efficiency can be evaluated in terms of energy:
“Cartridge efficiency is pretty straight forward — energy in vs. energy out. Most modern single-based propellants run around 178-215 ft/lbs of energy per grain. These figures give the energy potential that you’re loading into the rifle. The resulting kinetic energy transferred to the bullet will give you the efficiency of the round. Most cases operate at around 20-25% efficiency. This is just another way to evaluate the potential of a given cartridge. There’s a big difference between this and simply looking at max velocities produced by various cartridges.”
This story is about a great shooter, Joe Hendricks Jr., and his Eliseo RTS Tubegun, chambered in 6mm Competition Match. With this versatile rifle, Joe Hendricks Jr. won the 2019 CMP Cup Aggregate Title for Match Rifles. Joe comes from a long line of talented marksmen. His father AND his grandfather are elite competitive shooters. His dad has been a National Champion, and all three generations have shot together, shoulder to shoulder, on the Remington Rifle Team. Like grandfather, like father, like son.
Joe says: “I think it’s pretty cool that there have now been two major Across the Course Championships won by a Hendricks using a Gary Eliseo chassis, one by me this year, and one in 2014 when my father (Joe Hendricks Sr.) won the NRA National Championship.”
Photography by Meghan Hendricks.
Joe Hendricks Jr.’s Rifle — Eliseo RTS Chassis, Rem 40X Action, Krieger Barrel
Joe’s rifle is built on a Competition Machine RTS Target Model chassis. This Tubegun features a Remington 40X action with Pacific Tool & Gauge Bolt and Jewell trigger. The scope is a Leupold 6-18x40mm. The barrel is a Krieger chambered in 6mm Competition Match. Joe explains: “The 6mm Competition Match is a cartridge that my dad came up with. It is basically a .243 Winchester with a 31° shoulder.”
If you look carefully in the photo below, you’ll note the silver-toned, adjustable butt-plate. That’s an upgrade Joe added: “I did a small modification to the stock, where I put on an Anschutz buttplate instead of the standard one Gary Eliseo uses. This Anschutz hardware provides a little bit more adjustability.”
Here Joe Hendricks Jr. fires at 200 yards from the standing position.
The Standing Position — Why It’s Critical to Match Success
Joe told us: “As far as shooting strategies and training methods go, I shoot a lot of standing practice — at least 50 shots per session. I still train the other positions of course, but I believe if you start your day off with a great standing score, it really makes the rest of the day easy because then you don’t feel like you’re playing catch-up the whole time.”
Joe explains: “When I’m shooting standing, I shoot in a manner very similar to the way that Carl Bernosky does. He’s written a few articles about the standing position. He always talks about making sure the shot goes off inside his hold, and I’m the same way. I don’t try to do too much. I just let the gun do its thing and when/if it stops in the Ten Ring, I shoot the shot. If it doesn’t, I don’t.”
About the CMP Cup Two-Day Course of Fire
The CMP Cup is a two-day match comprised of two, 1000-point Aggregates, for a 2000-point Grand Agg. Each day, the competitors fire 100 shots total from the 200, 300, and 600 yard lines. The match starts with 20 shots slow fire standing at 200 yards. Next are two, 10-shot, rapid fire strings in 60 seconds from the sitting position. Next are two, 10-shot strings in 70 seconds prone at 300 yards (rapid fire prone). Each day’s course of fire concludes with two, 20-shot sequences of slow-fire prone at 600 yards.
6mm Competition Match Cartridge — Slower Powder Yields Better Barrel Life
My dad was shooting a 6XC for a while and was getting tired of going through almost two barrels a year. So, he came up with the 6mm Competition Match. Like I said, it is a .243 Winchester with a 31-degree shoulder. This delivers the same (if not better) velocity as the other popular 6mm cartridges, but we get almost double the barrel life because we increased the case capacity, so we can shoot a slower burning powder. The barrel I took to Camp Perry that won the CMP Cup had over 3700 rounds on it when I was finished. [EDITOR: Take note readers! Most 6mm barrels are toast after 2500 rounds.] Granted it definitely needed to come off at that point, but it obviously was still shooting well enough to win!
Accurate Load with Peterson Brass, Berger Bullets, and Vihtavuori N165
The two loads I shot all week were Berger 108gr BT behind Vihtavuori N165 in Peterson Cartridge Company brass for 200 and 300 yards, and then Berger 115 VLD behind N165 in Peterson brass for 600 yards. Both loads are easily going over 3000 FPS. I try to only use the best components for reloading, so that’s why I go with Berger, Vihtavuori, and Peterson. Obviously Berger and Vihtavuori quality are pretty known, but I believe Peterson is right up there with Lapua[.] I’ve visited the Petersen factory many times. I’m always blown away by the time and effort Peterson puts into everything.
Winning Marksmanship — the Mental Game
The other big thing I’ve been focusing on lately is my mental game. In order to be at the top of a sport, regardless of the sport, the athlete has to have a solid mental approach. For me, I’ve learned that my key is confidence. A good shooting buddy, who was with me the first day of the CMP Cup, suggested I was arrogant because I kept telling him I was going to win. Then I told him it was confidence not arrogance. If I was confident in my ability, I did not think there was any way I could lose. [Editor: To help build confidence and visualize success, we recommend With Winning in Mind, by Lanny Bassham, an Olympic gold-medal winning marksman.]
All in the Family — Three Generations of Hendricks Marksmen
Joe’s father, Joseph Hendricks Sr., has been a National Champion rifle shooter. Joe’s grandfather, Gary Hendricks, is also a talented marksman. In fact, all three men — grandfather, father, and son — shot together on the Remington Rifle Team. Joe says that the shooting sports have helped build strong family bonds. He and his father enjoy shooting together, and competing against one another: “I learn so much just by watching my dad… shoot. Even though I have been competing for 10 years now, I’m still incredibly new to the shooting sports compared to my dad. My father is always there to help.”
“I feel very privileged to have grown up in the family that I did, with not only my father as a competitive shooter, but my grandfather as well. I definitely would not be the person I am today, let alone the shooter, without either of them. At one point, all three of us were on the Remington Rifle Team. I’ve had the opportunity to shoot team matches with all three of us on one team, as recently as this past summer.”
“Initially when I began shooting competitively, I was putting a lot of pressure on myself. I wanted to be as good a shooter as my dad and grandfather. I was trying so hard that it was really affecting my scores negatively. Then one year, I told myself I was just going to have fun, and not worry about match scores. That year was the year I really started to win things, and shoot some good scores.”
“When my father won the NRA National Championship in 2014, I was so proud, but along with being proud, all it did was make me more motivated. Ever since I started shooting, I wanted to win a National Championship, but after he won, it just fueled my fire more. There is a bit of father/son rivalry. It’s a lot of fun if we are shooting right next to each other at the same time. We just give each other crap about shooting a bad a shot, or shooting a lower score by a point or an X.”
“My dad started shooting when he was around 10, so he has a vast amount of knowledge compared to most people, especially me. He is always there to help whenever I have a question on anything firearm or shooting related. To this day, whenever I’m done with a match, I always talk to my dad. He always has time to listen to what I have to say.”
This custom war wagon hauls varmint hunters around the Longmeadow Game Resort in Colorado.
Today is May Day, May 1st, so we are well into springtime. The woes of winter are behind us. For many shooters, Spring is a great season to head out to the varmint fields. Here are six items that can help ensure successful spring varmint adventures.
Six Great Products for Varmint Shooters
1. BarrelCool In-Action Fan
Busy Varmint shooters may expend hundreds of rounds in a day. That’s tough on barrels. One way to extend your round count is to use the ingenious BarrelCool device. This little yellow gadget fits in your action with a blower tube that goes into the chamber. A small electric fan blows cooling air through the barrel. It really works — folks who’ve purchased the $44.95 Barrel Cool and run temp strips on their barrel say the BarrelCool can significantly reduce the time it takes to cool down a hot barrel.
In the past, folks have tried various methods to cool barrels: water flushed through the bore, CO2 tanks, even battery-operated fish pumps. BarrelCool is a simpler, less costly, and much handier solution. Priced at $44.95, this small device can potentially can save you money by extending barrel life. To see how Barrelcool works, watch the video below:
2. Uncle Bud’s Bulls Bag Sandbag
On most varmint hunts we spend most of the time shooting from a portable bench with a pedestal-type rest (we like the SEB Mini). But it’s nice having a big, heavy X-Type sandbag rig also. These four-chamber designs, such as the Uncle Bud’s Bulls Bag, allow shooting from a truck hood or any flat surface. Some rifles with narrow fore-ends really benefit from the firm “hug” provided by these “butterfly” style sandbags. We like the 15″ Uncle Bud’s Bulls Bag, currently $80.00 at BullsBag.com (khaki/suede). Durable and well-made, it will provide years of service. There is also a 10″ version that is easier to carry, starting at $62.00. Forum member Stoner24mkiv likes a Bulls Bag for shooting from a vehicle. He also suggests: “[take] an adjustable bipod if you are going to do any walking. Have a fanny pack or backpack for extra ammo, water, bore-snake, etc. when you go on your walkabouts. Bring a Boonie hat for blocking the sun, sun glasses, sunscreen. High leather boots.”
3. Burris Scope with Built-In Laser Rangefinder
The Burris Eliminator is an impressive piece of electro-optical technology. With a push of a button, a built-in laser rangefinder senses the distance to your target and the Eliminator’s microprocessor instantly calculates the required hold-over based on your load’s ballistics. The calculated aiming point is then displayed in the reticle with an illuminated red dot on the vertical cross-hair. Just put the red dot on the target and make the shot. Easy as that. If you are working a large prairie dog field and constantly moving near to far and back again, this scope is really handy. We’ve used the Eliminator III out to 500 yards on small steel targets and it worked flawlessly.
Right now you can get the 5-20x50mm Burris Eliminator V model for $1183.99 on Amazon (#ad — you must add to cart to see this price). Or you can get the 4-16x50mm Burris Eliminator III model for $1167.40 on Amazon (#ad). Note: the Eliminator V has been replaced by the compact Eliminator 6, but that newer model costs $2499.99. The Eliminator III and V both offer better value for the price.
4. Hornady 17 HMR V-Max Loaded Ammo
For those distant prairie dog shots, you’ll want a centerfire round with some reach, such as a 22 BR or 22-250. However, for closer work, or for smaller varmints such as ground squirrels, the 17 HMR is hard to beat. There are many good factory rifles chambered for the 17 HMR, such as the Savage A17 (shown below). Right now Hornady 17 HMR ammo is on sale at AmmoASAP.com for $12.05 ($0.24 per round). That’s a good deal. This same ammo sells elsewhere for up to $18.00 per 50-round box. NOTE: Hornady also offers 17 HMR ammo with 20gr XTP hollow-point bullets. Both types work well.
5. Stick-On Temp Strips Monitor Barrel Heat
You never want your barrel to get too hot. Accuracy suffers when barrels over-heat, and excessive heat is not good for barrel life. So how do you monitor your barrel’s temperature? You can check if the barrel is “warm to the touch” — but that method is not particularly precise. There is a better way — using temperature-sensitive strips. McMaster.com (an industrial supply house) offers stick-on temp strips with values from 86° F to 140° F. A pack of ten (10) of these strips (item 59535K13) costs $12.66 — so figure it’ll cost you about $1.27 per barrel for strips. That’s cheap insurance for your precious barrels. For best barrel life, try to stay under 120 degrees F.
6. Low-Fouling Power for High-Volume Varmint Loads
For high-shot-count varmint safaris, you want a clean-burning powder that minimizes barrel fouling. While there are many great powders for the .223 Rem, we like Hodgdon CFE 223 for high-volume varmint loads. This powder really seems to keep barrels cleaner. Originally developed for U.S. rapid-fire military systems, CFE 223 incorporates a proprietary chemistry named “Copper Fouling Eraser”. Based on tests with extended shot strings, Hodgdon claims that, by using CFE™223 varmint hunters, match shooters, and AR shooters can maintain accuracy for longer periods, with less barrel-cleaning time.
Today is 4/30/25, the final day of April 2025, and there are some significant savings you can get at Precision Reloading, a leading vendor for reloading supplies, tools, shooting accessories, and hunting gear. With discount codes your can save up to $50 on your orders today. But act quick — these discount codes expire on May 1st, 2025.
Precision Reloading Spring Savings Discount Codes
Save up to $50 with Coupon Codes:
$50 Off Orders over $500 (Code:4325)
$25 Off Orders over $250 (Code:4225)
$10 Off Orders over $100 (Code:4125)
Get FREE Shipping at MidwayUSA
In addition to these discount codes, MidwayUSA is running a great promotion — you get FREE SHIPPING on purchases of $49.00 or more. This can save you $10, $20 or more on many purchases. There are some exclusions, but this is still a great deal. Simply Apply CODE FS042925 when you start your order. CLICK HERE for details.
NOTE — There are exclusions. FREE Shipping does NOT apply to clearance, drop ship, quantity limited products, guns, large/irregular products, select ammo crates, some products with a shipping weight over 20lbs, out of stock or special order products.
At the request of our readers, we provide select “Deals of the Week”. Every Sunday afternoon or Monday morning we offer our Best Bargain selections. Here are some of the best deals on firearms, hardware, reloading components, optics, and shooting accessories. Be aware that sale prices are subject to change, and once clearance inventory is sold, it’s gone for good. You snooze you lose.
NOTE: All listed products are for sale to persons 18 years of age or older. No products are intended for use by minors.
1. Graf & Sons — Primed Pulled Down Brass Sale
⏺️ » Good choice for high volume shooters — low cost primed brass
If you need reliable plinking brass and don’t want to spend a lot of money, consider pulled down primed factory-ammo brass. This is name-brand ammo that has been pulled apart for various reasons. NOTE: You get PRIMED big-name brass at very low prices (way less than new brass alone). Most of the brass is Federal or CCI. Choose among many rifle and pistol cartridge types including: 9mm Luger, 22-250, 22 Creedmoor, 6mm Creedmoor, .243 Win, 6.5 Creedmoor, .280 Ackley, 7.62×39, and .30-06 Springfield.
2. CDNN Sports — Walther P22 Target with StopBox, $219.99
⏺️ Very good .22 LR Target/Training pistol plus FREE security case
All shooters should have a quality .22 LR rimfire pistol with a good trigger, ergonomic grip, and excellent accuracy. With the Walther P22 Target Model, you can get all those things for just $219.99 at CDNN Sports, a great deal. Plus with your purchase (before 4/30/25) you get a FREE Walther Stop Box by mail-in rebate. The Stop Box ($99 MSRP) is a secure transport case with a programmable push button lock system. The P22 Target pistol is a nice rimfire handgun with a 5″ barrel plus forward ported compensator. The ergonomic grip has interchangeable backstraps.
3. Midsouth — Lee Challenger Press with BONUS Die Set, $83.99
⏺️ » Get good single-stage press AND die set
The LEE Challenger is the world’s best-selling single station press. The latest Gen III Challenger features an ergonomic lever plus convenient drop-tube for spent primers. Right now LEE is offering a FREE carbide die set with the purchase of the LEE Gen III Challenger Press. Chose one of five cartridge types: .223 Rem, 9mm Luger, .38 SPL/.357 Mag, .44 SPL/.44 Mag, and .45 ACP. Another good feature of the LEE Press is the Breech Lock Quick Change Die System — change dies instantly with a twist of the wrist.
4. Natchez — Spring Cleaning Event Sale, Up to 30% Off
⏺️ » Huge selection of cleaning products and tools on sale
If you need ANY kind of gun cleaning supplies and/or tools, definitely head over to Natchez for the Spring Cleaning Sale. You’ll find solvents, brushes, jags, cleaning rods, bore guides, mats, and even gun vises on sale. This is a great one-stop option for your gun maintenance needs. With this Natchez Annual Spring Cleaning Event you’ll find every type of cleaning product up to 30% off.
⏺️ » Very good choice for service rifle optic, now on SALE
Designed for Service Rifle competition, the Sightron S-TAC 1-4.5x24mm SSP SR1 Scp[e has precise windage/elevation controls and quality MC-333 lens coatings. This scope provides the max 4.5-power service rifle magnification with very good low-glare views through the glass. With a 30mm tube, the S-TAC 1-4.5x24mm SR1 is shockproof and nitrogen-charged for waterproofing.
6. MidwayUSA — Frankford Arsenal Tumbler Combo Kit, $94.99
⏺️ » Complete tumbling kit — tumbler, separator, bucket, and media
Cleaning brass is a key step in the reloading process. Here’s a complete brass tumbler set-up at a great price. The Frankford Arsenal Quick-N-EZ Case Tumbler Kit (#ad) includes: Quick-N-EZ Case Tumbler, Quick-N-EZ Rotary Media Separator, 4 oz. Brass Polish, 3 lb. Cleaning Media and a Plastic Bucket. Current price is $94.99 at MidwayUSA. This may ship FREE with a total MidwayUSA purchase of $99 or more.
⏺️ » Excellent funnel that fits perfectly on various neck sizes
Powder transfer into cases can be faster, cleaner, and more precise with the RCBS MatchMaster Aluminum Powder Funnel Kit. One of our editors uses this now because it’s the only funnel he’s tried that has never bridged powder. This $84.99 kit includes the fastest powder funnel on the market, six precision-fit adapters for popular calibers (.22, 6mm, 6.5mm, 7mm, .30, 338), and a nice, compact storage case. Another funnel kit option at a lower price point ($31.99) is the Lyman BrassSmith Pro Powder Funnel System which also features caliber-specific aluminum inserts that fit well.
7. Amazon — Precision Ball Micrometer, $34.99
⏺️ » Handy tool great for measuring neck wall thickness
There’s no better tool for measuring case-neck thickness than a ball micrometer. This quality HFS Precision Tube Micrometer with Ball Spherical Anvil (#ad) is just $34.95 at Amazon. The manufacturer claims accuracy to 0.0001″. The thimble design works well and the laser-etched scale and satin chrome-plated surface provide fast, accurate read-outs without glare.
⏺️ » Versatile 2-part shooting rest for pistols and hunting rifles
For sighting-in a hunting rifle or testing pistol loads, you’ll want a good basic gun rest. The very affordable Caldwell Matrix Adjustable Rest (#ad) works with both rifles and pistols. Use the front section by itself with a handgun, then attach the rear support for sighting-in and testing a hunting rig. The spring-loaded elevation system allows for fast one-handed, no wobble adjustment.
10. MidwayUSA — Pro Series Competition Shooting Mat, $39.99
⏺️ » Excellent mat — good size with nice padding and carry handle
MidwayUSA’s Pro Series Competition Shooting Mat is on sale for just $39.99 — 20% off the regular $49.99 price. This mat is bigger and better than MidwayUSA’s basic shooting mat. The Pro Series mat measures a full 74″ x 35″ and the padding is thicker. A zippered pocket on the front extension flap holds ammo or log book. There are pockets for bipod feet so you can pre-load your bipod. At $39.99 on sale this Pro Series mat is an excellent deal. Choose either OD green as shown, or Coyote Tan.
11. Amazon — A.I. Hand Warmers Rechargeable 2-Pack, $18.99
⏺️ » Great for hunters and field competitors in cold climates
Electric handwarmers are great for hunters and outdoorsmen. These A.I. Rechargeable Hand Warmers (#ad) offer precise warming capability plus very good 6000mAh battery capacity. By continuously checking the temperature of your hands, this unit ensures precise heat control for optimal comfort. The heat output is max’d at 130 degrees for safety.
As an Amazon affiliate, this site can earn revenues through sales commissions.
The RCBS Lock-Out Die can also be used with some Dillon and Hornady progressive presses.
If you load pistol or rifle ammo with a progressive press, we strongly recommend you get a Lock-Out Die from RCBS. This unique reloading die will prevent your progressive press from advancing if the dispensed powder charge is more or less than about 0.3 grains too high or too low. The Lock-Out Die really works. Your Editor uses it on his RCBS 2000 progressive press. I can affirm that a Lock-Out Die has “saved my bacon” a half-dozen times over the years when there was an over-charge (which could cause a Kaboom) or a low charge (which could cause a squib load).
The Lock-Out Die works by using a central die detection rod that sets its vertical position based on the height of the powder column in the case. Through an ingenious design, if the powder column height is too low or too high, the rod locks in place as you start to pull the press handle. This halts the press before the ram can lift and the cartridge plate can advance. Unlike a beeping alarm system (which can be ignored or defeated), the Lock-Out Die physically stops the movement of the press ram and prevents a bullet being seated in the “problem” case.
It takes a bit of tweaking to get the Lock-Out Die detection rod setting just right, but once it is correctly positioned, the Lock-Out Die works smoothly in the background. The Lock-Out Die won’t interfere with the loading process unless it detects a high or low charge — and then it positively stops the progressive loading cycle.
While crafted for use in RCBS progressive presses, the RCBS Lock-Out Die can also be used on a Dillon XL Progressive (see video below) or Hornady Lock-N-Load progressive — though it does take up one station which could otherwise be used for a final crimp die (after the seating die). The RCBS 2000 has one more station than a Dillon 550/650, so it’s an ideal platform for using the Lock-Out Die.
Learn More at UltimateReloader.com
On the UltimateReloader.com website, run by our friend Gavin Gear, you’ll find an excellent two-part series on the function and set-up of the RCBS Lock-Out Die. Part One explains how the Lock-Out Die functions, using cut-away illustrations. Part Two shows how to install and adjust the Lock-Out Die on various progressive presses. The Ultimate Reloader video at the top of this article shows setup of the RCBS Lock-Out Die on the Dillon XL-650 progressive press, while the Reloading Bench video below shows the Lock-Out Die on a Hornady LnL progressive.
Need something for the walls of your “man cave” or reloading room? Looking for a great birthday gift for one of your shooting buddies? The creators of the Cartridge Comparison Guide offer a collection of wall posters showing ammunition types from 17 caliber rimfire cartridges all the way up to giant 35mm military rounds. ChamberIt.com currently offers 12 different large wall posters that display a huge variety of cartridge types. For example, the American Standard Poster (shown above) contains every standardized cartridge mass produced in the USA as of 2021. The cartridges are 100% to scale (life size). These posters feature full color images on high gloss / high quality 100-lb poster paper.
For example, the Rifleman’s Classic Poster (below), a full 38 inches wide and 27 inches tall, is the most comprehensive. This $17.76 poster displays over 300 rifle cartridge types at true size (within 4/1000 of an inch). Cartridges shown range from .17 caliber all the way up to the big boomers (including some cannon shells). The Rifleman’s Classic Poster includes nearly all American Standardized Rifle Cartridges and many European rifle cartridges.
Rifleman’s Classic Poster Click to view large size poster.
Ammunition Performance Specifications Poster
There is also an interesting Ammo Performance Specs poster. This shows dozens of popular hunting cartridges with the velocity, energy, momentum and recoil for each cartridge displayed in a bar graph.
This shows the actual size of the Ammo Performance Poster as displayed on a wall.
Lapua, respected producer of outstanding cartridge cases, bullets, and ammunition, will be attending the 154th NRA Annual Meetings & Exhibits, scheduled for April 24-27, 2025, in Atlanta, Georgia. “Lapua uses the highest quality materials to provide shooters with components they can rely on” commented Director of Communications Morgan Joy-Twenter. “We encourage shooters and hunters to stop by booth #1916 to check out the wide range of Lapua products, including our new 7mm PRC, 6mm Dasher, and MaxRange Target bullets.”
New Lapua MaxRange Target Bullets
Lapua will offer new high-BC MaxRange Target bullets. These are designed for long-range precision rifle sports such as F-Class, Fullbore, PRS and other disciplines with distant targets, or where a very high-BC can help enhance long-range hits and accuracy. The first MaxRange Target offerings are a 6.5mm 144 grain and a .30 Caliber 175 grain.
New Lapua 6mm Dasher Cartridge Cases
New for 2025, Lapua will offer 6mm Dasher brass. The 6mm Dasher has long been a popular and versatile cartridge for many precision shooting disciplines such as 600-1,000 yard benchrest, varminting, and PRS/NRL competition. It is an extremely accurate cartridge that can drive 103-110gr match bullets at very accurate velocity nodes, and drive lighter 6mm varmint bullets at high speeds. With the new Dasher brass, you no longer need to spend time fire-forming 6mmBR brass into the higher-capacity Dasher. The Lapua 6mm Dasher brass is expected to arrive in Fall 2025.
New Lapua 7mm PRC Cartridge Cases
The 7mm PRC effortlessly delivers heaviest-in-class .284 caliber projectiles, which are coveted in today’s precision shooting and long-range hunting disciplines. F-Class and long-range match shooters have suffered from the lack of quality 7mm PRC cases and ammunition. Now that will change. Lapua will begin offering high-quality 7mm PRC cartridge cases for its loyal followers this fall.
New Bullets and Ammo Types from Berger
Berger, manufacturer of quality bullets and ammunition for competitive shooters and avid hunters, will attend the 154th NRA Annual Meetings & Exhibits in Atlanta Georgia. At booth #1916, Berger will showcase its entire product line, including new ammunition and bullet offerings.
For target shooters Berger now offers new .300 Norma Magnum ammunition with the 245 grain Long Range Hybrid Target bullet. This ammo has shown excellent accuracy in testing (see above). In addition, Berger has new .338 Norma Magnum ammo featured the 300 grain Hybrid OTM Tactical bullet. CLICK HERE for product specifications.
Berger has expanded its hunting ammo line to include .30-06 168 grain and 185 grain Classic Hunter, and .300 WSM 185 grain Classic Hunter. In addition, Berger will offer new hunting bullets in 2025. There’s a new 6.8mm/270 caliber 150 grain Hybrid Target bullet that should work great in .270 Winchester, .277 Fury, and 6.8 Western rifles. Berger will also offer a new 217 grain, .30 caliber Elite Hunter bullet.
NRA Event Schedule and Special Events
The 2025 NRA Annual Meetings & Exhibits runs April 24-27 at the Georgia World Congress Center in Atlanta, Georgia (see MAP below). The large Exhibit Hall will be open 9 AM to 6 PM on Friday and Saturday, and 10 AM to 5 PM on Sunday, providing attendees with the opportunity to explore a host of shooting and hunting products. CLICK HERE for EVENT Schedule.
Winchester’s new “Introduction to Ammunition — Ammo 101” is a four-part series including custom illustrations and information for four major ammunition categories: rifle, pistol, rimfire, and shotshell. The Ammo 101 series provides a detailed overview of centerfire rifle, centerfire pistol, rimfire, and shotshell ammunition, showcasing ammunition construction, components, calibers, and common usage. The Ammo 101 resource is free to download from Winchesters.mediaassets.com. Or, simply click one or more diagrams below. Each image will launch a large PDF which you can print or download.
TIP: Click Each Image for Full-Screen Printable PDF
Shown below are the first four ammunition information sheets prepared by Winchester. These show all the key components of cartridges and shotshells, and explain the functions. These diagrams are useful for training, and for persons getting started in reloading.
Ammo 101 Centerfire Rifle Cartridge Diagram (click for PDF)
Ammo 101 Rimfire Cartridge Diagram (click for printable PDF)
Ammo 101 Pistol Cartridge Diagram (click for printable PDF)
Ammo101 Shotshell Diagram (click for printable PDF)
About the Ammo 101 Series
The FREE Ammo 101 resources can help instructors nationwide who introduce new entrants to the shooting sports and hunting. Instructors can incorporate these resources into their training presentations, use them as handouts, or have them printed locally.
“The basics of ammunition… is what we want to deliver with the Ammo 101 series,” said Matt Campbell, Winchester V.P. of Sales & Marketing. “With millions of people across the United States starting their journey in the shooting sports as new firearm owners, providing easy-to-understand information on ammunition types is one way we can help educate our customers.”
If you load pistol or rifle ammo with a progressive press, we strongly recommend you get a Lock-Out Die from RCBS. This unique reloading die will prevent your progressive press from advancing if the dispensed powder charge is more or less than about 0.3 grains too high or too low. The Lock-Out Die really works. Your Editor uses it on his RCBS 2000 progressive press. I can affirm that a Lock-Out Die has “saved my bacon” a half-dozen times over the years when there was an over-charge (which could cause a Kaboom) or a low charge (which could cause a squib load).
