RCBS Summit Press Works Great in the Shop and in the Field
Gear Review by Mark LaFevers
With its innovative “moving die/static cartridge” design, the new RCBS Summit Press definitely demonstrates “out of the box” thinking. Unlike other presses, the case does not move. Rather, the reloading die comes down to the case. We are happy to report that this unique “upside-down” reloading press works great.
We have tested the new RCBS Summit Press in the workshop and in the field. We’ve now loaded hundreds of rounds with the press. It is smooth, solid, and easy to use. The spent primer ejection/capture system works great (our testers preferred the Summit’s simple, foolproof primer capture to the Rockchucker’s capture system). Most importantly, the Summit produces very straight ammo that gave excellent results on the target in actual matches.
We compared ammo loaded with the Summit with ammo loaded on an RCBS Rockchucker press. The Summit gave up nothing to the bigger press. Cartridge base-to-ogive measurements of Summit-loaded ammo were just as tight as with ammo loaded on the Rockchucker. Run-out, measured with a concentricity gauge, was the same or better (about .002 or less on bullet nose). Most importantly, the Summit loads accurate ammo. In fact, at one match, scores shot with Summit-loaded .284 Win ammo were actually better than scores shot (in the same gun) with ammo loaded on a Rockchucker:
Rockchucker .284 Win Loads (Day 1): 188-2X
Summit .284 Win Loads (Day 2): 192-5X
Despite its small footprint, the Summit is very stable — it doesn’t tip, wobble, or rock. The two front mounting bolts hold it firmly in place — the Summit doesn’t need a rear anchor. This, combined with the fact that the Summit has no overhang, makes the new press ideal for a mobile application. For field use (at the range), our tester Mark LaFevers mounted the Summit press on a small platform secured to his trailer hitch (on top of a steel post). This set-up worked great, as you can see in the video below:
Watch Reloading (Sizing/Decapping, Expanding, Bullet Seating) with Summit Press
Photo shows Redding Micrometer Seating Die and .284 Win Cartridge
Mark tells us: “I think the Summit press worked out sweet mounted on the hitch pedestal. The receiver hitch pedestal I made will switch tools between a heavy barrel vise I made and the Summit press. Instead of securing the pedestal with a standard 5/8″ hitch pin, I drilled and tapped for 1/2″-13 bolt to draw the insert up tight against the receiver, eliminating wobble. For charging rounds, I bought 150 plastic test tubes with caps and racks so I can avoid weighing powder charges in the field, unless I want to make changes on the fly.”
The new Summit Press features a rugged cast-iron frame with all-steel linkages. The press is very strong with minimal flex and slop. This allows you to “bump” your case shoulders and seat bullets with great precision and repeatability. The handle can be switched from right to left side (good for southpaws), and the open-front design provides good access, facilitating quick die changes*. The 4.5-inch opening allows you to work with tall cases. Beneath the shell-holder is a spent primer catcher (not shown in photos). The new Summit press has a beefy 2-inch diameter ram, with compound linkages for plenty of leverage. A zerk fitting is included for easy lubrication. The press will accept larger bushings for oversize 1-inch dies.
Summit Press Retails for $207.94
The new Summit Press (RCBS item #09290) lists for $269.95. However, Midsouth Shooters Supply offers the Summit Press for $207.94. An optional short handle from RCBS costs $15.27 at Midsouth ($19.95 MSRP).
Similar Posts:
- RCBS Summit Reloading Press — Unique Design That Works
- SHOT Show Report: New RCBS Summit Single-Stage Press
- RCBS Offers Limited Edition Red, White, & Blue Summit Press
- New RCBS Summit Single-Stage Press
- Three Press Comparison Test: Rock Chucker, Co-Ax, Summit
Share the post "RCBS Summit Press Works Great in the Shop and in the Field"
Tags: Mark Lafevers, RCBS, Reloading Press, Rockchucker, Sizing Die, Summit Press, Trailer Hitch
Excellent write up and the video was great, very professional voice over. The piece that was made to allow the same die settings for both presses was a good idea that looked to be extremely well executed. It was hard to tell, but from what I could see, when he was checking runout, the indicator was well out on the bullet, which means that his .002 is likely as good or better than .001 that someone else might claim, measured closer to the end of the case neck. The detail about ogive head variation being less than his Rockchucker was interesting and while one may speculate as to the cause, it gets to the core of an issue that is very important when loading for the highest level of accuracy.
I think the press is a good idea, but what would really be nice is if they would put a clamp/s on the press so that you can mount it on a shooting bench. It looks like you may be able to use a couple of c-clamps and mount this on a bench.
Aditionally the debris from decapping
( very abrasive black dust) is kept from contact with the ram thereby prolonging the accuracy of the machine and almost eliminating wear when properly lubed.