Why You CANNOT Rely on the MV Printed on the Ammo Box!
When figuring out your come-ups with a ballistics solver or drop chart it’s “mission critical” to have an accurate muzzle velocity (MV). When shooting factory ammo, it’s tempting to use the manufacturer-provided MV which may be printed on the package. That’s not such a great idea says Bryan Litz of Applied Ballistics. Don’t rely on the MV on the box, Bryan advises — you should take out your chrono and run your own velocity tests. There are a number of reasons why the MV values on ammo packaging may be inaccurate. Below is a discussion of factory ammo MV from the Applied Ballistics Facebook Page.
Five Reasons You Cannot Trust the Velocity on a Box of Ammo:
1. You have no idea about the rifle used for the MV test.
2. You have no idea what atmospheric conditions were during testing, and yes it matters a lot.
3. You have no idea of the SD for the factory ammo, and how the manufacturer derived the MV from that SD. (Marketing plays a role here).
4. You have no idea of the precision and quality of chronograph(s) used for velocity testing.
5. You have no idea if the manufacturer used the raw velocity, or back-calculated the MV. The BC used to back track that data is also unknown.
1. The factory test rifle and your rifle are not the same. Aside from having a different chamber, and possibly barrel length some other things are important too like the barrel twist rate, and how much wear was in the barrel. Was it just recently cleaned, has it ever been cleaned? You simply don’t know anything about the rifle used in testing.
2. Temperature and Humidity conditions may be quite different (than during testing). Temperature has a physical effect on powder, which changes how it burns. Couple this with the fact that different powders can vary in temp-stability quite a bit. You just don’t know what the conditions at the time of testing were. Also a lot of factory ammunition is loaded with powder that is meter friendly. Meter friendly can often times be ball powder, which is less temperature stable than stick powder often times.
3. The ammo’s Standard Deviation (SD) is unknown. You will often notice that while MV is often listed on ammo packages, Standard Deviation (normally) is not. It is not uncommon for factory ammunition to have an SD of 18 or higher. Sometimes as high as 40+. As such is the nature of metering powder. With marketing in mind, did they pick the high, low, or average end of the SD? We really don’t know. You won’t either until you test it for yourself. For hand-loaded ammo, to be considered around 10 fps or less. Having a high SD is often the nature of metered powder and factory loads. The image below is from Modern Advancements in Long Range Shooting: Volume II.
4. You don’t know how MV was measured. What chronograph system did the manufacturer use, and how did they back track to a muzzle velocity? A chronograph does not measure true velocity at the muzzle; it simply measures velocity at the location it is sitting. So you need to back-calculate the distance from the chrono to the end of the barrel. This calculation requires a semi-accurate BC. So whose BC was used to back track to the muzzle or did the manufacturer even do that? Did they simply print the numbers displayed by the chronograph? What kind of chronograph setup did they use? We know from our Lab Testing that not all chronographs are created equal. Without knowing what chronograph was used, you have no idea the quality of the measurement. See: Applied Ballistics Chronograph Chapter Excerpt.
5. The MV data may not be current. Does the manufacturer update that data for every lot? Or is it the same data from years ago? Some manufacturers rarely if ever re-test and update information. Some update it every lot (ABM Ammo is actually tested every single lot for 1% consistency). Without knowing this information, you could be using data for years ago.
CONCLUSION: Never use the printed MV off a box of ammo as anything more than a starting point, there are too many factors to account for. You must always either test for the MV with a chronograph, or use carefully obtained, live fire data. When you are using a Ballistic Solver such as the AB Apps or Devices integrated with AB, you need to know the MV to an accuracy down to 5 fps. The more reliable the MV number, the better your ballistics solutions.
On our main Accurateshooter.com website, you’ll find a comprehensive review of the STM system for cleaning cartridge brass with stainless media. To clean brass with stainless media, start with five pounds of small stainless pins sold by StainlessTumblingMedia.com. Place these along with a gallon of water, a little liquid cleaner, and two pounds of cartridge brass in a rotary tumbler, and run the machine for one to four hours.
Forum Member Tests STM System
Our reviewer, Forum member Jason Koplin, purchased the STM media and a new Thumler’s Tumbler. He then tested the STM cleaning procedure on his own brass, including some extremely dirty and tarnished “range pick-up” brass. Jason was thoroughly impressed with how well the STM process worked — as you can see from the “before and after” photos below. Brass which looked like it was ready for the scrap heap was restored to “like-new” appearance. The process works equally well on both rifle brass and pistol brass. Jason observed that one surprise benefit of the STM cleaning procedure is a big reduction in noise. Jason said the water-filled rotary tumbler was much quieter than his vibratory tumblers.
You’ll want to read Jason’s full review which shows more before and after images. The full article features a “how-to” video created by Forum member Cory Dickerson, the young man who pioneered the stainless tumbling process and founded STM. The video shows how to load brass, media, and cleaner solutions into the tumbler, and how to separate media from brass once the tumbling is done.
Many of our readers have never had a chance to shoot much past 600 yards. How far away does a 1000-yard+ target really seem to the naked eye? Well this short video answers that question. Gorilla Ammo, the video’s producers, used a camera-carrying aerial drone to fly downrange from the firing line all the way out to 1122 yards (and back again). Watch the drone footage at 0:00-0:07 and especially 0:48-1:03. The “bird’s-eye view” really gives you a sense of the distance. The “fly-back” at 0:48-1:03 time-mark is what makes this video worth watching.
The video features prone shooting at steel targets placed at 750 and 1122 yards. We do apologize for the lame, “oh so serious” voice-over which attempts to make this rather ordinary range session seem like some kind of life-changing experience. (Frankly, you may just want to turn the sound off — it’s that annoying.) It’s really not that big a deal to hit steel at 750 yards with a quality AR-15, chambered in .223 Rem, shooting Sierra 77 grain MatchKings.
Hitting Steel at 1122 Yards with 2540 FPS Ammo Can Be Challenging
The 1122-yard hits are a bit more impressive. Gorilla Ammo lists a relatively sedate 2540 fps Muzzle Velocity for its .223 Rem 77gr SMK ammunition. According to JBM Ballistics, at 1125 yards, that 2540 fps load has 68.3 MOA of drop from a 100-yard zero (firing at sea level and 80° F ambient). Morever the bullet goes trans-sonic around 750 yards (losing stability) and is traveling just 933 fps at impact. And the wind’s the killer — at 1125 yards, with this bullet/load, a mere 2 mph, full-value wind change can move the Point of Impact over three feet!
Vihtavuori has updated and enhanced its reloading information, adding VV powder load recipes for many more cartridge types. Data is now online for 64 rifle cartridge types and 26 pistol cartridge types. You’ll find the updated reloading data on the Vihtavuori Website. Bookmark this link: www.vihtavuori.com/en/reloading-data/about-reloading.html.
The updated online information supplements the Vihtavuori Reloading Guide (2016 Edition) available in PDF format. The online Reloading Database has dedicated sections for Rifle Cartridges, Pistol Cartridges, and Cowboy Action. There is also a handy, FREE Reload Mobile App for iOS and Android.
Vihtavuori’s Rifle Reloading Database is now very comprehensive. Many of the popular modern match cartridges such as the 6.5×47 Lapua and 6.5 Creedmoor are now included, and of course you’ll find the 6mm PPC, 6mmBR, and 6XC. (There is no .284 Win or 7mm RSAUM data unfortunately.) You will find recommended load recipes for all the following cartridges:
.204 Ruger
.221 Remington Fireball
.222 Remington
.22 Hornet
.22 PPC-USA
.223 Remington
.22-250 Remington
.223 WSSM
.243 Winchester
.243 WSSM
6mm PPC-USA
6mmBR Norma
6 XC
6mm Remington
.240 Weatherby Magnum
6.5 Grendel
6.5 x 47 Lapua
6.5 Creedmoor
6,5 x 55 Swedish Mauser
6,5 x 55 Swedish Mauser/ SKAN
6.5-284 Norma
.25-06 Remington
.260 Remington
.270 Winchester
.270 WSM
.270 Weatherby Magnum
7 mm-08 Remington
7 x 57
7 x 64
7 mm Remington Magnum
7 mm WSM
7 mm RUM
7 x 57R
7 mm Weatherby Magnum
7,5 x 55 Swiss GP31
.30 Carbine
.30-30 Winchester
.300 AAC Blackout
7,62 x 39
.300 Savage
7,62 x 53R (7,62 Russian)
.308 Winchester
.30-06 Springfield
.300 Lapua Magnum
.300 Remington Ultra Magnum
.300 Winchester Magnum
.300 Weatherby Magnum
.30-.378 Weatherby Magnum
.300 H&H Magnum
.300 WSM
.303 British
8 x 57 IRS
8 x 57 IS (8 mm Mauser)
.338 Winchester Magnum
.338 Lapua Magnum
9,3 x 62
9,3 x 66 Sako
9,3 x 74R
.375 H&H Magnum
.416 Rigby
.444 Marlin
.45-70 Government
.458 Winchester Magnum
.50 Browning
.32 S&W Long N.P.
.32 S&W Long Wadcutter
.357 Remington Maximum
.357 Magnum
.357 SIG
.38 Super Lapua
.38 Super Auto
.38 Special
7 mm GJW
7 mm TCU
7 mm BR Remington
7,62 x 25 Tokarev
9 mm Luger
9 x 21
9 x 23 Winchester
.40 S&W
10 mm AUTO
.41 Remington Magnum
.44 S&W Special
.44 Remington Magnum
.45 ACP
.45 Colt
.45 Winchester Magnum
.454 Casull
.500 S&W Magnum
.50 AE
Story Tip by EdLongrange. We welcome reader submissions.
At the request of our readers, we provide select “Deals of the Week”. Every Monday morning we offer our Bargain selections. Here are some of the best deals on firearms, hardware, reloading components, and shooting accessories. Be aware that sale prices are subject to change, and once clearance inventory is sold, it’s gone for good. You snooze you lose.
1. Stocky’s Stocks — Composite Stock with Bedding Block, $199.99
Here’s a killer deal on a versatile Stocky’s Long Range Stock with aluminum V-block bedding system. For just $199.99, order this for Rem/Rem Clone long actions or short actions, with either narrow or wide (varmint/tactical) barrel channel. This would be a good choice for a varmint rifle. This is also offered with a matte black, tan, or olive baked-on textured finish for $239.99.
2. Sportsmans — .45 ACP Ammo, 300 Rds $84.95 with Rebate
The .45 ACP is probably our favorite centerfire pistol cartridge. It is reliable, inherently accurate, and makes big, easy-to-see holes in paper. Here’s a good deal for .45 ACP shooters. Sportsmans Outdoor Superstore is selling 300 rounds of American Eagle .45 ACP 230gr FMJ ammo for $114.95 in a handy plastic ammo can. And with factory rebate, you can knock thirty bucks off that price. Through the end of 2016, Federal Ammunition is offering $30.00 cash back on this ammo. CLICK HERE for Rebate Form.
Fine Print: Maximum of $30.00 rebate. Purchase must be made before December 31, 2016. Coupon must be received by January 31, 2017. Consumer submits coupon with UPCs written and original cash register receipt and/or dated itemized sales invoice (photocopies not accepted). Please allow 6-8 weeks for delivery. Total redemptions limited to five (5) of each product per name, address and household.
3. Natchez — Special 5 Reloading Press Kit, $199.99
This is an excellent entry-level reloading kit, which is on sale for $199.99 at Natchez Shooters Supplies. We like the relatively compact Special 5 press for most reloading duties. Eventually you may want to add an additional, large heavy press, but this will get the job done. This kit includes an RCBS Powder Measure, Digital Scale, Powder Trickler, Hand Priming Tool, Load Manual, Loading Tray, and more. It’s hard to beat this combination of tools for under $200.00.
4. Southern Shooters — 17 HMR Ruger American Rimfire. $252.63
With ballistics far superior to a .22 LR, the 17 HMR is ideal for Prairie Dogs and small varmints out to 180 yards or so. Now you can get a reliable, name brand 17 HMR rifle for a very attractive price. That’s right, Southern Shooters is selling the 17 HMR Ruger American Rimfire, with 22″ barrel, for just $252.63. FFL required. For other vendors with this rifle, CLICK HERE.
5. Amazon — Lyman Case Prep Xpress $94.99
The Lyman Case Prep Xpress lets you chamfer inside and out, brush your necks, clean/uniform primer pockets, and ream military crimps. On sale at Amazon.com with $94.99 Prime pricing, this is a good deal. Lyman’s Case Prep Xpress sells elsewhere for $130.00 or more. Here is a review from a Verified Purchaser: “The unit is quiet, sturdy, and the attachments do what they are supposed to do. It already has made a difference in my reloading speed, and most importantly, my comfort. I highly recommend this unit.” (Strafer, 4/7/14)
6. Natchez Shooters Supply — 325 Rounds .22 LR Ammo, $22.99
This Federal .22 LR ammo is just 7 cents per round — the kind of pricing on bulk rimfire ammo we used to see in the “good old days”. Act quickly, this $22.99 Federal .22 LR Ammo deal won’t last long. Each box contains 325 rounds — enough ammo for many sessions at the range. The bullets are 40 grains, solid lead.
7. Sportsman’s Guide — Frankford Arsenal Case Tumbler Kit
For just $69.99, this Frankford Arsenal Kit provides everything you need to clean brass: Vibratory Tumbler, Rotary Media Separator, Bucket, Corn Cob Media (3 lbs.), and Brass Polish. The Case Tumbler holds up to 600 9mm cases or 350 .223 Rem cases. The separator system is generous, with a 3.5-gallon bucket. NOTE: Sportsman’s Guide Buyers Club members can purchase for $62.99.
8. Amazon — Neiko Digital Calipers, $17.74
Even if you have a good set of calipers, you may want to get one of these Neiko 01407A Digital Calipers. The #1 best-selling digital caliper on Amazon.com, this Neiko tool features a large LCD Screen and measures up to 6.0 inches. With over 2300 customer reviews, this product has earned an overall rating of 4.4 out of 5 stars. It’s hard to go wrong for $17.74, even if you just use these as a spare set for measuring group sizes and case trim lengths.
U.S. Rifle Team (F-TR) Selects New Berger 200.20X Bullet for 2017 World Championships
Berger Bullets has released new .30 caliber bullet that could be a game changer for the F-TR discipline — a bullet with exceptional accuracy and very high BC. Berger’s NEW 200.20X Hybrid Target Bullet is the result of extensive research and development in partnership with the U.S. Rifle Team (F-TR), world champion shooters, and accuracy enthusiasts within the long range shooting community.
The new 200.20X has a 0.640 G1/0.328 G7 BC compared to 0.616 G1/0.316 G7 for the older 200 grain .30 caliber Hybrid. That’s a significant reduction in drag. Recommended twist for the new bullet is 1:10″, same as with the earlier 200-grainer.
Berger Chief Ballistician and U.S. Rifle Team (F-TR) member Bryan Litz said, “This is the ideal bullet for F-TR and similar long-range disciplines. The 200.20X has a longer boat tail and nose, with shorter bearing surface which equates to less drag, a higher ballistic coefficient, and fewer points lost to the wind. The BC of the new 200.20X is 4% higher than the existing 200 grain Target Hybrid (G7 BC of 0.328 vs. 0.316). The shorter bearing surface also makes the 200.20X easy to load and shoot in standard chambers. New shooters won’t need special reamers or costly gunsmithing to make this bullet perform.” Bryan himself is switching to the new 200.20X: “After winning the 2015 National Mid-Range and Long Range F-TR Championships with the Berger 215 grain Target Hybrid, I’m switching to the 200.20X because it’s an even better option.”
Bryan tells us that new 200-20X bullet requires a 1:10″ twist to achieve full stability and performance (BC) in most conditions, but you can shoot it out of a 1:11″ twist with a minor decrease in BC. For a stability analysis, enter this bullet in the Berger Stability Calculator with a weight of 200.2 grains, and a length of 1.508″ to get stability results for your particular rifle and atmospheric conditions.
After extensive field testing, this new 200.20X bullet has been adopted as the official .30 caliber match projectile for the U.S. Rifle Team (F-TR). The team verified that this new bullet offers very impressive performance — the higher BC equates to less wind drift, and this bullet has shown exceptional ability to “hold waterline”. Check out this 1000-yard group by Team member Dan Pohlabel, as shown on an electronic target monitor.
To learn more about the new .30 caliber 200.20X Hybrid Target Bullet and its development, visit the Berger Bullets Blog for details. These 200.20X bullets are available right now through your favorite authorized Berger Bullets vendors.
About the U.S. Rifle Team (F-TR)
The two- time World Champion, U.S. Rifle Team (F-TR) is comprised of 30 shooters and coaches who have dedicated themselves to four years of training and preparation to represent the United States at the 2017 World Championships to be held in Canada. They compete all over the world at various ranges out to 1,000 yards.
Buy Bullets and Support U.S. Rifle Team (F-TR)
Eric Stecker, President of Berger Bullets said, “We are proud to be the Official Bullet of the U.S. Rifle Team (F-TR). To support our team, Berger Bullets will donate $1.00 for every box of 200.20X bullets sold towards U.S. Team expenses for the upcoming 2017 F-TR World Championships, which will be held at the Connaught Ranges in Ottawa, Canada.”
Coating bullets with a friction-reducing compound such as Molybdenum Disulfide (Moly) offers potential benefits, including reduced barrel heat, and being able to shoot longer strings of fire between bore cleanings. One of the effects of reduced friction can be the lessening of internal barrel pressures. This, in turn, means that coated bullets may run slower than naked bullets (with charges held equal). To restore velocities, shooters running coated bullets are inclined to “bump up” the load — but you need to be cautious.
Be Careful When Increasing Loads for Coated Bullets
We caution shooters that when your start out with coated bullets in a “fresh barrel” you should NOT immediately raise the charge weight. It may take a couple dozen coated rounds before the anti-friction coating is distributed through the bore, and you really start to see the reduced pressures. Some guys will automatically add a grain or so to recommended “naked” bullet charge weights when they shoot coated bullets. That’s a risky undertaking.
Instead we recommend that you use “naked” bullet loads for the first dozen coated rounds through a new barrel. Use a chronograph and monitor velocities. It may take up to 30 rounds before you see a reduction in velocity of 30-50 fps that indicates that your anti-friction coating is fully effective.
We have a friend who was recently testing moly-coated 6mm bullets in a 6-6.5×47. Moly had not been used in the barrel before. Our friend had added a grain to his “naked” bullet load, thinking that would compensate for the predicted lower pressures. What he found instead was that his loads were WAY too hot initially. It took 30+ moly-coated rounds through the bore before he saw his velocities drop — a sign that the pressure had lowered due to the moly. For the rounds fired before that point his pressures were too high, and he ended up tossing some expensive Lapua brass into the trash because the primer pockets had expanded excessively.
LESSON: Start low, even with coated bullets. Don’t increase your charge weights (over naked bullet loads) until you have clear evidence of lower pressure and reduced velocity.
Procedure After Barrel Cleaning
If you shoot Moly, and clean the barrel aggressively after a match, you may want to shoot a dozen coated “foulers” before starting your record string. Robert Whitley, who has used Moly in some of his rifles, tells us he liked to have 10-15 coated rounds through the bore before commencing record fire. In a “squeaky-clean” bore, you won’t get the full “benefits” of moly immediately.
To learn more about the properties of dry lubricants for bullets, read our Guide to Coating Bullets. This covers the three most popular bullet coatings: Molybdenum Disulfide (Moly), Tungsten Disulfide (WS2 or ‘Danzac’), and Hexagonal Boron Nitride (HBN). The article discusses the pros and cons of the different bullet coatings and offers step-by-step, illustrated instructions on how to coat your bullets using a tumbler.
Grizzly Industrial and Bullets.com President Shiraz Balolia pulled off a stunning feat of marksmanship recently, winning his third straight F-Open title at the Canadian F-Class National Championships. It wasn’t easy — conditions were tough, as was the competition — there were top shooters from around the world, including many past U.S. Champions. Shiraz had a slim, one-point lead after Day 2, but Balolia ended up tied on total points (and V-Count) with Emil Kovan at the end of the third and final day. But when the cards were compared, a string of Vs on Day 3 secured Shiraz the win via tie-breaker. Thus Shiraz achieved the memorable “three-peat”, winning Canada’s 2016 F-Open National Championship to complement his 2015 and 2014 victories.
Three-Peat at Connaught — 2016 F-Open Canadian Championship
by Shiraz Balolia This trip to Ottawa for the Canadian National Championship was a specially important one. The U.S. Team tryout process and practice was to take place for two days prior to the National Championship as the next F-Class World Championship is going to be held in Ottawa in August of 2017.
Connaught Range is a fantastic range that is very well run. Pullers are provided as part of your entry fee and matches are run at different times of the day, even into the evening. The flags are heavier than the ones we use in USA and are notorious for lying to the shooter. Matches are shot in pair firing mode which means one shooter takes a shot and the other scores. You cannot simply rattle off a shot as soon as the target comes up.
Crazy Hot Conditions at the Connaught Range
The first day the winds were mild, but tricky and the temperature was 102° F. I had never shot in such weather and ended up in the 6th place for the day. The second day had several matches at 900 meters and the wind picked up, with a 105° F recorded temperature, causing havoc with everyone. In one of my matches at 900 meters I took my two sighters and my first shot for record was a 3 (equivalent to an 8 in USA). To top it off I shot another 3 a few shots later. Liar, Liar, flags on fire! Anyway, I dropped 7 points in that match only to find out some very good shooters had dropped over 10! I moved to top position for the two-day Aggregate.
The third and final day was one string of 20 shots with shooters squadded by their two-day Aggregate ranking. So I was paired with Emil Kovan, while the third position shooter was paired with the fourth-ranking shooter et cetera. We all shot in identical conditions.
Après Moi, le Déluge — Not Your Gentle Drizzle
Then came a vicious rainstorm. We waited out the storm for two hours before we shot. The rain was really, really nasty and coming down really hard. We were all huddled under the U.S. Open Team’s tent.
Shiraz and Emil Battle to the End…
Finally, after the long delay, we got back to the firing line. And it went down to the wire. Emil shot a 100 with 3 Vs and I shot a 99 with 12 Vs. When the dust settled, we ended up with the same score and total V-Count (611-61V). The tie would be resolved by a “count-back” procedure. I had a stack of Vs at the end of my string and that won the match. What a fight!
Shiraz told us that this third championship was the toughest: “A while back, I had rotator cuff surgery on my shooting arm and had not shot a match in 9 months. I barely was able to test loads for three weeks before I shipped my ammo and did not know what to expect.” He says that winning “did not even sink in for a few days and looking back, I think this will be something I will cherish forever.”
Shiraz’s win came against very tough competition. Shiraz notes: “The whole U.S. Team, the whole Canadian Team, many South Africans, Germans, British, Ukrainians and others were present. We had several past US National Champions present as well and it was a great honor to shoot with all of them.”
Note: This is a photo from 2013, there may be slight changes in the rifle.
The rifle features a BAT Machine ‘M’ action, with a 31″, 1:10″-twist Bartlein barrel. The scope is a March 10-60x52mm, which sits on a +20 MOA angled rail. The primary stockwork, including fitting of the adjustable cheek-piece and buttplate, was done by Alex Sitman of Master Class Stocks. Shiraz customized the stock with finger grooves, fore-end channel, and a bottom rear slide. Shiraz did the final stock finishing as well.
Gun Components
BAT Machine Action
Master Class Stock, modified by Shiraz
Bartlein Barrel, 1:10″ Twist, 31 inches long
Fitted Barrel Harmonic Tuner
March 10-60x Scope with fine crosshair and 3/32″ dot
Caliber & Load
.300 Winchester Short Magnum (WSM)
215gr Berger Hybrid bullets, 2870 FPS
Norma .300 WSM Cases
H4831SC Powder
Tula (Russian) Primers
NOTE: Shiraz was not running anywhere near max: “I chose a light load for Ottawa due to the range limits as my other accurate node is 100 FPS faster and almost at the range limit.”
At the request of our readers, we provide select “Deals of the Week”. Each week we offer our Bargain selections. Here are some of the best deals on firearms, hardware, reloading components, and shooting accessories. Be aware that sale prices are subject to change, and once clearance inventory is sold, it’s gone for good. You snooze you lose.
LABOR DAY HOLIDAY SPECIALS
We are publishing our Deals on Sunday this week because many of the best bargains are Labor Day Weekend Specials. There are also Special 10% OFF PROMOTIONS running this weekend. We want readers to be able to take advantage of these holiday specials before the discount codes “time out”.
1. Brownells — Labor Day Weekend Sale & Free Shipping ($99+)
Brownells is offering great pricing on a host of products this weekend. You’ll find bargains on Berger Bullets, RCBS Rockchuckers, AR components, Timney Triggers, Magpul Stocks, Rimfire Ammo, Centerfire Ammo, Range Bags, and more. Plus all Geissele products are on sale this holiday weekend. In addition, with CODE L27 you can FREE Ground Shipping on orders over $99.00. This free shipping offer expires on 9/5/2016 at 11:59 PM CST. CLICK HERE for Labor Day Specials.
2. Amazon — Vortex 4-12x50mm AO Scope, $174.00
The NRA is introducing a new Mid-Range Tactical Prone Match for AR platform rifles with bipods. Optics up to 12X will be allowed. If you’re considering participating in this new Mid-Range competition, here’s a fine Vortex 4-12x50mm AO Crossfire II scope for under $175.00. That’s a steal. This second-focal-plane scope features front parallax adjustment and a BDC reticle. Put the money you save on optics into a premium barrel and quality match trigger.
3. Ammomen — Winchester .22 LR Ammo $15.50 for 235 Rounds
We are finally starting to see .22 LR rimfire ammo come down to very affordable levels. With this Winchester bulk pack special you get 235 rounds for just $15.50. That works out to just 6.6 cents per round (or $3.30 for 50 rounds). This .22 LR ammo is loaded with 36 grain copper-plated lead HP bullets. The ammo is rated at 1280 fps in rifles, 1085 fps in pistol.
4. Savage Arms — Rifle Rebates up to $75.00
With the Save on a Savage Rebate, you can get $75.00 on Savage Trophy Hunter, DOA Hunter, Model 14/114 or Model 16/116; or get $30.00 back on any AXIS or A17™ synthetic stock rifle. Shooters who purchase any bolt-action Savage rimfire, including the B.MAG and Rascal, will be eligible for a $25 mail-in rebate. Firearms must be purchased between August 11, 2016 and September 25, 2016. NOTE: This program also includes the popular semi-auto A17 17 HMR which was voted ‘Rifle of the Year’ by both NRA American Hunter and Guns & Ammo magazines. CLICK HERE for Rebate Coupon.
5. Cabelas — 10% Off Labor Day Special with Free Shipping
Act quickly guys, this Cabelas.com offer expires 9/5/16, at 11:59 pm Eastern Time. Throughout the Labor Day Weekend you can get 10% off most online merchandise, plus FREE Shipping for orders over $99.00. This includes ammo purchases, but not firearms. This is an online-only promotion, not valid at Cabela’s retail stores. Use Code 6TENOFF during online checkout. Some heavy or oversized items will require paid shipping and handling.
6. Amazon — Leight MAX NRR33 Earplugs, $7.50 for 50 Pairs
These Howard Leight NRR33 Max plugs are your Editor’s favorite foam earplugs. Between shooting, motorcycling and mowing lawns, I probably have Max plugs in my ears 2-3 days a week. This is a very good price for a bulk pack of 50 pairs. And if you act soon, you can get free shipping to boot.
7. Beretta USA — Labor Day Sale, Up to 60% Off
Beretta is offering big discounts — up to 60% Off — during its Labor Day Outlet Store Sale. You can save on shooting accessories, clothing, gun cases, holsters, gunstocks, choke tubes, barrels, scope rings, grips and much more. You’ll also find great deals on Tikka and Sako stocks (Beretta is the distributor for Tikka and Sako). For example, a high-grade Sako 75 Hunter DLX stock is marked down from $878.00 to $439.00. In addition, Beretta is offering Free Shipping on Orders over $89.00.
8. Precision Reloading — $15 Hazmat Fees on Powder and Primers
If you’re purchasing powder, primers and other Hazmat items, you can save up to $25.00 per order with this offer from our friends at Precision Reloading. Some vendors charge as much as $40.00 for Hazmat fees (on top of regular shipping). This fall Precision Reloading is lowering its Hazmat charge to just $15.00 per order. And yes, you can combine powder and primers in the same order. NOTE: Normal shipping charges apply, and total package weight may not exceed 70 pounds.
If you have a 6.5 Grendel rifle and recently purchased ammunition from Prvi Partizan (PPU), do NOT LOAD or shoot this ammunition. PPU, the manufacturer, is recalling ALL of its 6.5 Grendel ammunition.
This recall applies to ALL PPU-made 6.5 Grendel ammunition.
DO NOT USE OR SELL THE FOLLOWING PRODUCTS:
PRVI 6.5 Grendel Ammunition Box
PP6.30 6.5 Grendel FMJBT 110-grain
PP6.31 6.5 Grendel HPBT 120-grain
According to PPU: “Because of different chamber sizes in certain rifles, 6.5 Grendel cartridges may be subjected to excessive chamber pressure. Use of these products may result in firearm damage and possible serious personal injury.”
If you have any 6.5 Grendel ammunition or brass manufactured by PPU, please email info@ppu-usa.com or call (203) 375-8544 to arrange for its return and replacement.
On our main 
This trip to Ottawa for the Canadian National Championship was a specially important one. The U.S. Team tryout process and practice was to take place for two days prior to the National Championship as the next F-Class World Championship is going to be held in Ottawa in August of 2017.
