Eurooptic vortex burris nightforce sale




teslong borescope digital camera barrel monitor


As an Amazon Associate, this site earns a commission from Amazon sales.









February 28th, 2012

Berger’s New 6mm "Column" Bullet for Short-Range Benchrest

Berger Bullets has released a new 6mm (.243 caliber) bullet for short-range (100-300 yards) benchrest applications. The new bullet (shown below right), is called the “6mm BR Column”. This name does not mean the bullet is designed just for the 6mm BR cartridge. Rather it is designed for all 6mm short-range benchrest (BR) rifles, most of which are 6 PPCs (for group shooting at least). The “Column” in the name comes from the fact that Berger has optimized the height of the lead core column inside the bullet. Testing revealed that bullets which had very uniform core column heights shot more accurately and were also easier to tune. Does the new “Column” bullet work? Well, noted benchrest shooter Lou Murdica has already used them to win a Two Gun Agg in Florida against “big name” competition. Thankfully, you won’t have to wait long to try these bullets out — Berger says the new 6mm BR ‘Column’ projectiles will be available in mid-March, 2012. Call Berger at (714) 447-5422 to order.

Berger 6mm BR column bullet

Bullet Characteristics — Accurate and Easy to Tune
Berger’s Ballistician and lead bullet designer Bryan Litz says this new ‘Column’ bullet should be less sensitive to seating depth: “We worked very hard to produce a bullet that has a wider ‘tuning window’ for peak accuracy. This means there may be several seating depths where it shoots well. We also expect that it can shoot well at different speed nodes, but this will be dependent on your barrel.” The estimated G1 BC for these bullets is 0.277. The meplat is 0.062″, typical of benchrest bullets in this weight class. There is a small pressure ring in the bullet. Recommended twist rate is 1:13.5″ but the bullet should stabilize in a 1:14″ twist-rate barrel.

Berger’s Eric Stecker tells us: “There have been benchrest bullets in the past which were well-known for achieving consistently small groups over a wide tune range in many rifles and loads. One example of this was the Euber bullet. The seemingly ‘magical’ performance of these bullets has been attributed to special dies, stars aligning, owl feathers, or some other unknown influence. However, Bryan Litz has found that there are specific mass balance and aerodynamic properties which allow a bullet to mitigate dispersion and shoot precisely over a wide range of imperfect launch dynamics.”

Dispersion Mitigation in Bullet Design — Bryan Litz Explains
Bryan LitzThe science of dispersion-mitigating bullets is understood, but until now, no one has ever deliberately designed a bullet that has these specific attributes. There have been other bullets which have accidentally achieved the partial effect and the resulting bullets became very well known. Three key things are required to develop an effective dispersion-mitigating bullet:

1. The knowledge required to design a dispersion mitigating bullet.  
2. A bullet-maker with the ability to fabricate the design precisely.
3. The means by which to test the bullets extensively to determine optimal configuration.

Berger’s 6mm ‘Column’ bullet is specifically designed to mitigate the component of dispersion related to alignment. Variables related to bullet/bore axis alignment include tight necks, turning necks, bullet jump, chamber concentricity, powder charge, and so on. These are all variables which will be less critical for the new Berger 6mm ‘Column’ bullet.

To be realistic, these new bullets only mitigate dispersion effects related to axis alignment, NOT aiming error, wind deflection, or poor shooting.

Four Years of Prototype Testing
Yields Superior Bullet Design

Using his knowledge of design factors that mitigate (reduce) dispersion, Berger’s bullet designer Bryan Litz went to work creating a bullet design that had a wide, forgiving tune range. This means that the bullet shoots well with a wide variety of loads and seating depths. Bryan came up with three different shapes. Then for each of these three bullet profiles, Berger tested three different core column heights to identify the truly optimal design. Over the next four years, Lou Murdica shot thousands of test rounds in the data capture phase of the project. When testing concluded, one bullet proved to be head and shoulders above the others in its ability to shoot well at the widest variety of loads and seating depths.

The prototype bullet design that shot best in Berger’s tests has entered production as the new Berger 6mm BR ‘Column’. You’ll notice that there is no listed weight. Berger doesn’t list weight because Berger learned that the bullet’s mass is not as important as the overall balance of the bullet, which is achieved with a specific internal lead column height. Due to slight variations in copper and lead material batches, one lot may weigh 64.8 gr while another lot might weigh 65.1 grains or 64.6 grains. Berger says: “So long as the column of lead is the correct height to achieve the desired balance” the bullets should perform, no matter what the average weight of a given lot of ‘Column’ bullets may be. That said, when loading for a match, you’ll want to load all your ammo with bullets from the same lot.

Berger is now accepting orders for the new 6mm BR ‘Column’ bullets. The first lots should be available around March 16, 2012. Call Berger at (714) 447-5422 for pricing info or to place an order.

Permalink Bullets, Brass, Ammo, New Product 4 Comments »
February 28th, 2012

Salazar Examines Prone Stocks for High Power Shooting

German Salazar, a top prone shooter and “head honcho” of the fine RifllemansJournal.com website, has crafted an excellent new article on stock design. Writing for Precision Shooting magazine, German compares traditional stocks, such as the MasterClass Prone, with more modern, modular designs, such as the Eliseo TubeGun and Ross Precision stock. German, who shoots match rifles built with each type of stock, explains the pros and cons of the different designs, and explains how to optimize the stocks’ adjustments for best fit and function. German also explains the best methods to attach and bed an action to each of the designs.

Salaza highpower stock review

Salaza highpower stock review

For a limited time, German’s excellent article is available online, courtesy of Precision Shooting Magazine. If you’re a High Power shooter, or you are interested in the design, construction, and engineering of modern competition stocks, this article is a “must-read”.

CLICK HERE to read FULL STORY

Salaza highpower stock review

Permalink - Articles, Gunsmithing No Comments »
February 28th, 2012

Affordable Choate Tactical Stocks for Remingtons and Savages

Choate Machine & Tool, www.riflestock.com, offers an affordable tactical stock design for Remington ADL/BDL long and short actions, and Savage 10,11,12,16 (short) and 110,111,112,116 (long) actions. Choate’s ADL/BDL and Savage tactical stocks sport an 80/20 blend of polypropylene and fiberglass, wrapped around a full-length aluminum bedding block. These stocks come with an adjustable spacer system allowing for .75″ of adjustment in length of pull, a rail integrated into the bottom of the fore-end to mount a bipod, and four swivel studs for customized carry options. The stocks have a wide barrel channel allowing most barrel contours to free-float.

Russell Simmonds F-TR F-class

The Choat ADL/BDL tactical stocks have some very nice features. We like the fact that the toe (underside) of the buttstock is relatively straight, and long enough to work well in a rear sandbag. The built-in rail on the fore-arm’s underside allows you to move your bipod fore and aft, plus you can easily mount other accessories. The spacer system is a nice feature in an “economy” stock, which retails for just $221.99 at MidwayUSA.com. The stock is sufficiently well-built and rigid. However, it does have a very thick (wide) pistol grip section, which may be a negative for persons with small hands.

Very Positive Review from Stock Owner
CLICK HERE for an an honest, thorough owner’s assessment of the Choate tactical stock for the Rem BDL. Posting on SnipersHide.com, the reviewer, MAX100, provides good photos, including side-by-side comparisons with a $400 HS Precision tactical stock. Max 100 concludes the Choate stock is an excellent performer for the price. Max100 writes: “The New Choate Tactical stock is well-made and offers a lot for the money. It is made of virtually indestructible Rynite polymer. This stock is … built like a tank. I gave the butt of the stock a few good whacks with a hammer with no damage whatsoever. Try that with a fiberglass stock. The lower cost of the stock will offer a good alternative for those on a budget. I feel for the most part Choate did a very good job on this stock.”

Stock Sizing: Choate’s Rem tactical stocks fit Remington short action receivers with 6.50-inch action screw spacing, or Rem long actions with 7.35-inch action screw spacing. The Savage Model 10 version fits the Savage factory detachable magazine actions with 4.4″ action screw spacing, while the Model 110 Choate stock fits Savage actions with 5.062″ action screw spacing.

Choate-Stocked F-TR Rifle Wins World & Euro Championships
We know that some folks scoff at the Choate product line, assuming that a lower price means that Choate stocks can’t perform as well as all-fiberglass stocks that may cost two or even three times as much. Well, to those “sticker-price snobs”, consider this. Britain’s Russell Simmonds won the 2009 F-TR World Championship (at Bisley, England) shooting a .308 with a Choate stock. Russell then went on to win the British League Championship (the second time in a row) AND the European Championship. Russell’s gun features a Barnard action, True-flite barrel, Choate “Ultimate Sniper” stock and 8.5-25×50 Leupold scope.

Russell Simmonds F-TR F-class

Permalink Competition, New Product 2 Comments »