Shooting Sports USA (SSUSA) offers a wide selection of informative articles on marksmanship techniques. If you shoot prone, “hard-holding”, you know how important proper positioning and technique can be. There is a SSUSA article that every prone shooter should read — whether you shoot air rifle, smallbore, or High Power. Compiled wtih the help of some of the country’s best prone marksmen, this article, How to Master Prone Shooting, provides a step-by-step guide to perfecting your prone position technique.
How to Master Prone Shooting — SSUSA by NRA Staff
The prone position is the most precise of the rifle shooting positions. It is used in many different shooting events at distances as close as 5 meters and as far away as 1,000 yards, and beyond that in long-range disciplines such as PRS and NRL. Prone shooting is very popular among shooters whose training time is limited, because it does not require as much practice. Age has little effect on a shooter’s ability to do well in prone; many older shooters are able to continue competing successfully in prone matches.
Here is a sample, listing STEP ONE, the basics of the prone position:
Step One: Study the Position
The prone position is steady because it is low, which gives a wide base of support to help keep the rifle still. Below are the key features of the prone position.
1. Straight line form left hand through left arm, side and leg.
2. Head tipped down comfortably.
3. Right hand grips rifle lightly.
4. Body lies behind rifle. Angle to rifle is 10 to 20 degrees.
5. Right knee bent slightly, toe pointing out.
6. Rifle lies on heel of left hand, fingers relaxed.
7. Left elbow rests to left of rifle.
8. Sling (if present) supports weight of rifle. Left arm relaxed.
9. Body rests slightly more on left side.
10. Left leg straight, toe pointing inward or straight back.
There are FIVE MORE STEPS described in detail with specific actions to perform, in the FULL Article. For example, in STEP FOUR (Sling Adjustment), the article explains: “Put the sling high on the arm and tighten the sling keeper. Wrap the arm around the sling so that the sling comes across the left hand and forearm.”
Howa Model 1500 Mini Action rifles are popular with hunters and varminters. These rifles have smooth actions, very good 2-stage triggers, are lighter than most rifles, and are very affordable. And now Mini Action rifles are offered in the modern 22 ARC cartridge. Developed for the AR-15 and small actions, the 22 ARC is efficient and allows use of high-BC bullets in a very compact action. We think the 22 ARC is a great choice for a field-carried varmint rifle.
The Howa Mini Action series has been offered with a half-dozen chambering options and now the 22 ARC is available — a very good option for varmint shooting and small game. Hornady claims the 22 ARC outperforms all .22-caliber cartridges in its class. In the Mini Action, the 22 ARC rivals 22-250 performance, has dual-purpose match and varmint applications and is designed to take advantage of today’s long ogive, high-BC bullets with a variety of ammo offerings available from Hornady. Along with the 22 ARC, HOWA Mini Action rifles are offered in .223 Rem, 7.62×39, 6.5 Grendel, 6mm ARC, 350 Legend, 300 Blackout.
Howa 22 ARC Mini Action Features and Options:
Barrel Options: 22″ Steel, 20″ Light Varmint Steel, or 20″ Carbon Fiber Barrel (all 1:7″ twist). Threaded barrels are suppressor-ready.
Receiver (Action): Compact machined receiver with forged one-piece bolt and tool-less firing pin removal
Stock Options: Synthetic OD, Black & Yote dip, Walnut, Carbon Fiber, or APC Chassis
Trigger: Excellent two-stage trigger with 3-position safety
Magazine: Standard 5-round detachable magazine
HOWA Mini Action bolt is 09″ shorter than a short action, and 1.4″ shorter than a long action.
About the 22 ARC Cartridge
The 22 ARC (Advanced Rifle Cartridge) is a compact cartridge that fits into an AR-15 but is equally at home in a bolt action. The modern catridge shape is efficient and allows longer bullets to be fitted. The case capacity and sized offers performance, that rivals the 22-250. This makes the 22 ARC a good choice for varminters who want something with more punch than a .223 Remington case.
Hornady states: “The 22 ARC was engineered to use modern, high-BC bullets. Designing the cartridge and chamber in unison provides consistent accuracy, great velocity spreads and an outstanding shooting experience. This cartridge is the result of careful and meticulous design, following the same proven methodology as the highly acclaimed 6mm ARC.”
The 22 ARC is tailored to fit the AR-15 platform with a maximum overall length of 2.260″. In both ARs and bolt guns such as the Howa Mini, the cartridge should feed and function very well.
“The press is the heart of the handloading operation, also traditionally the most expensive single tool employed…” — Laurie Holland
British competitive shooter Laurie Holland has reviewed three popular, single-stage reloading presses for Target Shooter Magazine (targetshooter.co.uk). Laurie bolted up a Forster Co-Ax, RCBS Rock Chucker Supreme, and RCBS Summit to his reloading bench and put the three presses through their paces. These three machines are very different in design and operation. The venerable Rock Chucker is a classic heavy, cast-iron “O”- type press that offers lots of leverage for tough jobs. The smaller RCBS Summit press is an innovative “upside-down” design with a large center column and open front. It offers a small footprint and easy case access from the front. The Co-Ax is unique in many respects — dies slide in and out of the upper section which allows them to “float”. The cartridge case is held in the lower section by spring-loaded jaws rather than a conventional shell-holder.
If you are considering purchasing any one of these three presses, you should read Laurie’s article start to finish. He reviews the pros and cons of each press, after processing three different brands of brass on each machine. He discusses ergonomics, easy of use, press leverage, smoothness, priming function, and (most importantly), the ability to produce straight ammo with low run-out. The review includes interesting data on case-neck run-out (TIR) for RWS, Federal, and Norma 7x57mm brass.
Review Quick Highlights:
RCBS Rock Chucker Supreme
“My expectations of the antediluvian RCBS Rock Chucker Supreme’s performance weren’t over high to be honest as I mounted it in the place of the Summit. As soon as I sized the first of the stretched RWS cases though, I saw why this press has been such a long-running favorite. The workload was considerably reduced compared to the other two presses and doing 40-odd cases took no time at all with little sweat — it just eats hard-to-size brass.”
RCBS Summit Press
“Despite its massive build and long-stroke operating handle, [the Summit] took more sweat than I’d expected, even if it was somewhat less work than with the Co-Ax. Although the Summit is apparently massive, I noticed that the die platform would tilt fractionally under the heaviest strains[.] It is nevertheless a very pleasant press in use and bullet seating was a doddle — the few examples tried proving very concentric on checking them afterwards. The optional short handle would be valuable for this task.”
Forster Co-Ax
“[On the Co-Ax], the operating handle is above the machine, located centrally [with] twin steel links at the top end of the press dropping down to the moving parts. The Co-Ax incorporates [many] novel features, principally its automatic and multi-case compatible shell-holder assembly with spring-loaded sliding jaws, very neat spent primer arrangements that allow hardly any gritty residues to escape and foul the moving parts and, the snap-in/out die fitment that allows rapid changes and lets the die ‘float’ in relation to the case giving very concentric results. I own this press and it meets my handloading needs very well.”
The Where To Shoot Mobile App quickly locates shooting ranges near you, drawing on North America’s most comprehensive directory of shooting ranges. Users can search by current location, state, or zip code. Once you locate a range, you can view activities offered along with a summary of range facilities. You can even get driving directions. If you don’t want to install an App, you can also access the NSSF shooting range database and maps via the NSSF Where-to-Shoot webpage.
The app is modeled after NSSF’s popular WhereToShoot.org® website and is updated frequently with range information for every U.S. state and Canadian province. Once you’ve located a place to shoot, the App can provide directions to the range. The App also includes video tips for shooters, news, and firearm-safety information.
Want to see some handgun shooting fun on TV tonight? Today Shooting USA television will feature the 2024 IDPA National Championship on the Outdoor Channel.
The International Defensive Pistol Association (IDPA) sponsors practical competitions that focus on skills used for concealed pistol training. More than 370 competitors gathered at the 2024 IDPA Nationals in Alabama. The event ran August 15-17, 2024 at the CMP Talladega Marksmanship Park in Talladega, Alabama.
The IDPA event airs Wednesday 1/8/25 at 9:00 PM Eastern/Pacific, 8:00 PM Central on the Outdoor Channel. If you miss the broadcast you can view the episode at any time for $0.99 on Vimeo. Or, subscribe to see all Shooting USA shows on Vimeo as often as you wish for just $1.99 per month.
Basics of IDPA Competition — Equipment and Scoring
Most of our readers are rifle guys, but it’s fun to shoot a pistol match now and then. You don’t need a lot of equipment, and if you shoot IDPA (Int’l Defensive Pistol Assn.) matches, you can really win with a $400 pistol and $25.00 worth of bulk 9mm ammo. That’s a bargain compared to what you’ll spend on a competitive PRS or F-Class rig and custom hand-loads.
If you want to get into the IDPA game, Shooting Sports USA has a good article that explains the basic rules and classifications. IDPA is not your grandad’s bullseye pistol match. There is movement and action. Stages are timed, and competitors engage targets from cover if available. Singled-handed shooting is sometimes required, as is shooting while moving. You can compete with pretty much any handgun suitable for self-defense — but no $4000 Raceguns with fancy optics. The fact that you can be 100% competitive without spending a ton of money is what makes IDPA so popular.
Shooting Sports USA polled IDPA shooters at the 2016 IDPA Nationals to determine their favorite gun brands and models. The #1 choice was the 9mm Glock 34 for the SSP (Standard Service Pistol) and ESP (Enhanced Service Pistol) Classes. Next most popular was the Smith & Wesson M&P Pro. We expect in 2024 many competitors are now using SIGs and Walthers, while Glock usage has declined.
Along with SSP and ESP, there are three other main IDPA classes: Custom Defensive Pistol (CDP) for .45 ACPs (mostly 1911 types), Concealed Carry Pistol (CCP), and Revolver (REV). All classes have a minimum power factor. Scores are based on time and shot placement on the IDPA target.
IDPA Scoring System
The official IDPA Target (right) has multiple scoring zones. If you don’t hit the target’s center mass zone or head zone (both appear green in illustration), you drop one or three points. Here’s the formula: Score (in seconds) = Time + Points Down + Penalties. In IDPA, “points down” (and penalties) are added to your time. If you hit the outer edge of the target, you get 3 points down. Nearer center can be 1 point down. Center hit or head shot is 0 points down. See IDPA Scoring for Dummies.
The Taurus 327 T.O.R.O. Defender Revolver has earned an NRA Golden Bullseye Award as the Shooting Illustrated2025 Handgun of the Year. The 327 T.O.R.O. earned this honor for innovative design, dependable performance, and good value. Taurus says this is the first-ever small-frame revolver that’s optics-ready from the factory. This compact carry revolver is chambered for the .327 Federal Magnum cartridge, and is designed principally as a compact defensive pistol, though it can also be used for IDPA competitions.
The NRA Golden Bullseye Awards, now in their 23rd year, honor the shooting industry’s new and innovative products as selected by the editorial teams of Shooting Illustrated, American Rifleman, and American Hunter magazines. “These awards have become the most prestigious in the entire firearm industry,” said Michael J. Sanford, Deputy Executive Director of NRA Publications.
The Taurus 327 T.O.R.O. is part of the Taurus Optics Ready Option (TORO) platform for small-frame revolvers. This optics-ready capability is a notable upgrade for a small revolver — an important evolution for a defensive pistol. Red dot optics allow faster aiming, particularly in low-light situations. There are three main types of red dot sights – reflex, prismatic, and holographic. Although each works differently, they serve the same purpose: making target acquisition quick, easy, and accurate. Engineered for versatility, the Taurus 327 T.O.R.O. is chambered in .327 Federal Magnum, offering flexibility with compatibility for both .32 H&R Magnum and .32 S&W cartridges.
For many Americans, real incomes have stayed flat in recent years, while inflation has increased the cost of living very significantly in the past four years under Biden. Accordingly, it’s important to save money whenever possible. Prices are going up, but wages aren’t following (for most of us). Here are six ways shooters can save money on gear purchases and other shooting-related expenses.
1. Watch for Our Deals of the Week. Every Monday, in our Daily Bulletin, AccurateShooter.com offers some of the best deals to be found. We search the web to find great deals on ammo, reloading components, optics, tools, firearms, gun safes, electronics and more. It’s not unusual to find savings of 20-35% through our Deals of the Week. And many of our vendors are now offering special deals just for AccurateShooter.com readers.
2. Check Out the Forum Classifieds. There are great deals to be found every day in the AccurateShooter Shooters’ Forum. The latest deals are displayed in the right column of every Forum page. To see all the listings, browse through the Forum MarketPlace section which has four main categories:
Guns, Actions, Stocks, & Barrels
Tools, Dies, Rests, Reloading Components & Misc
Scopes, Optics, Sights, Rings, Bases Etc.
Commercial Sales by Paid Sponsors
3. Share a Ride to Matches. Fuel prices are on the rise — Regular-grade gasoline is over $5.00 per gallon in California now and around $3.10/gallon nationwide. With many shooters living 30-100 miles from the nearest range, fuel remains a big part of a shooter’s hobby budget. We’d say 90% of shooters drive solo to matches, often in large, gas-guzzling trucks. If you drive 200 miles round-trip to attend a match in a 20-mpg vehicle, you’ll burn over $31.00 worth of gasoline on your trip. That adds up. By simply sharing the ride with one fellow shooter you cut your fuel expenditures in half. And, if you alternate vehicles with a buddy from one match to the next, you save on vehicle wear and tear. At $0.65/mile (overall operating costs) consider the savings.
4. Use Discount Codes to Save. It’s always smart to check for discount codes before you buy. In the Daily Bulletin, we feature “Deals of the Week” every Monday morning, and we provide discount Coupon Codes when available. These can reduce the price substantially or lower shipping costs. Search codes for Brownells, Creedmoor Sports, EuroOptic, Graf’s, Midsouth, Powder Valley, Sportsman’s Warehouse, KYGUNCO, MidwayUSA, and Precision Reloading. Check your email also — some discount codes are only announced in email newsletters. If you can’t find a Coupon Code for your preferred vendor, visit Gun.deals and/or RetailMeNot.com. Both those sites list current coupon codes, and RetailMeNot.com covers thousands of vendors.
5. Shop for “Demo” Optics. Modern high-quality optics can easily cost $2000.00 or more, often exceeding the value of the rifle on which they are mounted. However, you can often save 20-30% by purchasing demo optics. These are normally display units used at trade shows. They may have slight ringmarks, but otherwise they are “as new”, having never been carried in the field or used on a rifle that has fired live ammo. When purchasing demo scopes, you should always ask about the warranty before consummating the sale. However, most demo scopes from name-brand manufacturers come with full factory warranties. EuroOptic.com and Natchezss.com are two respected vendors that offer a good selection of demo optics.
6. Train with Rimfire Rifles. Good match-grade centerfire, hand-loaded ammo, counting premium bullets, powder, primers, and brass (figuring 10X loads), can now exceed $1.60 per round. And if your $600 (as chambered and fitted) competition barrel is toast after 1500 rounds, add $0.40 for barrel deprecation per shot. So you’re effectively spending two bucks a round total! By contrast, you can get quite good .22 LR target ammo for under $0.18 per round. Good rimfire barrels last a long, long time, so you don’t have to be concerned about wearing out your barrel quickly. A quality rimfire barrel can retain its accuracy for 7,000 rounds or more. If you run the ballistics, a .22 LR round at 100 yards can emulate the wind drift experienced by a centerfire cartridge at long range. This allows for effective cross-training with much less expensive ammo.
The last half-inch or so of your barrel is absolutely critical. Any damage (or abnormal wear) near the crown will cause a significant drop-off in accuracy. Here are ways you can check the end of your barrel, using a common Q-Tip.
Use Q-Tip for Barrel Inspection To find out if you have a burr or damage to your crown, you can use an ordinary Q-tip cotton swab. Check the edges of the crown by pulling the Q-tip gently out past the edge of the crown. If you have a burr, it will “grab” the cotton and leave strands behind.
Larry Willis has another way to use a Q-Tip: “Here’s a neat trick that will surprise you with how well it works.” Just insert a Q-Tip into your barrel (like the picture below), and it will reflect enough light so that you can get a real good look at the last half inch of rifling and the crown of your barrel. In most cases you’ll find that this works much better than a flashlight. Larry tells us: “I’ve used this method about a jillion times. Q-Tips are handy to keep in your cleaning supplies anyway. This is a good way to judge approximately how well you are cleaning your barrel when you’re at the range. It’s also the best way to examine your barrel when you’re in the field.”
At the request of our readers, we provide select “Deals of the Week”. Every Sunday afternoon or Monday morning we offer our Best Bargain selections. Here are some of the best deals on firearms, hardware, reloading components, optics, and shooting accessories. Be aware that sale prices are subject to change, and once clearance inventory is sold, it’s gone for good. You snooze you lose.
NOTE: All listed products are for sale to persons 18 years of age or older. No products are intended for use by minors.
1. Brownells — Crimson Trace Optics Sale
⏺️ Quality Crimson Trace scopes now at very significant discounts
Brownells is running a major sale right now on quality Crimson Trace Optics. Along with rifle scopes (both FFP and SFP versions) with a wide range of magnification levels, there are red dots for pistols. With this notable Crimson Trace Optics Sale you can save up to 60% on quality optics with very positive user reviews. We would definitely consider a FFP Crimson Trace for a PRS rifle.
⏺️ High-quality match-winning 6BR brass, works for Dasher and 6BRA too
The original 6mmBR Norma cartridge and its wildcats such as the 6mm Dasher and 6BRA have been hugely popular for many disciplines — Benchrest, PRS/NRL, varminting. But with this popularity has come short supply. 6mmBR brass has been hard to find in recent months. But take heart — Whidden Gunworks has Lapua 6mmBR Brass in stock at $119.99 for 100 cases — a good price. If Whidden Gunworks sells out, Bruno Shooters also has Lapua 6mmBR brass in stock for $122.80 per 100, just a few bucks more.
3. Palmetto SA — SAR9 Sport 9mm Pistol, $299.99
⏺️ Save $300 off MSRP on good full-size 9mm pistol
This is a great deal for a modern, reliable 9mm pistol with better ergonomics than a Glock (at less than half the price). The lightweight polymer-framed, striker-fired SAR9 points naturally and has three insertable back straps to customize fit. We like the 20-degree grip angle which points well for most users. This ported slide version with 5.2″ barrel is a great gun for IDPA, USPSA, and other pistol matches. The listed $299.99 sale price is $300.00 off the original $699.99 MSRP. The slide has two threaded holes that allow an optic to be attached, but it does not have a removable plate like some newer pistols.
4. Graf & Sons — Unis Large Rifle Primers, 5000 for $399.00
⏺️ Get Large Rifle Primers — in stock now at Graf’s
Large rifle primers have been hard to source lately. But Graf & Sons now has ample inventories of Unis Large Rifle Primers. You can get a big 5000-count case of UNIX Large Rifle Primers for $399.00, a 15% discount. That price works out to just eight cents per primer. Manufactured in Bosnia and Herzegovina, Unis “Ginex” primers are used by major ammunition manufacturers world-wide. With consistent ignition and uniform size these will work for anything from plinking to competition.
5. Creedmoor Sports — $20 Off All Rifle Cases
⏺️ Creedmoor Sports makes some of the best soft cases — save $20 now
For decades Creedmoor Sports has offered some of the best fabric rifle cases you can buy. These cases are very popular with Palma, High Power, and Service Rifle competitors. They have quality zippers and handy outside pockets and are offered in a variety of sizes and colors. Right now these Creedmoor Sports gun cases are $20 OFF on Sale through 1/11/25. With a variety of size, pocket, and color options this is a great opportunity to pick up a new gun case for 2025.
6. Scheels — Forster Co-Ax Primer Seater, $119.99
⏺️ Great product, with significant savings over other sellers
If you load lots of cartridges, it’s wise to have a high-leverage, stack-loading bench-mounted primer tool that gives repeatable results. This allows you to prime hundreds of cases efficiently without the hand pain from repetitive gripping. A great choice is the Forster Co-Ax Primer Seater with E-Z-Just Shell Holder Jaws. This system has an adaptive rim holder so separate shell holders are not needed. The E-Z-Just jaws can grip rifle and pistol cases with a rim thickness of .045″ to .072″. Primers stack in vertically-oriented primer tubes (separate tubes for large primers and small primers are supplied). The primers stack sideways — outer diameter to outer diameter — for added safety.
7. Amazon — Frankford Arsenal Tumbler Combo Kit, $99.99
⏺️ Complete tumbling kit — tumbler, separator, bucket, and media
Cleaning your brass is a critical step in the reloading process and we found a great kit if you’re in the market for one. The Frankford Arsenal Quick-N-EZ Case Tumbler Kit (#ad) has everything you need to get started. With Quick-N-EZ Case Tumbler, Quick-N-EZ Rotary Media Separator, 4 oz. Brass Polish, 3 lb. Cleaning Media and a Plastic Bucket you’ll be up and running in no time.
8. Amazon — Wheeler Trigger Pull Gauge, $61.49
⏺️ Good very consistent and reliable trigger gauge
Competitive shooters as well as hunters need to accurately monitor trigger pull weights. Having optimal (and consistent) pull weights is key for shooting performance and safety. You may also need to verify pull weight to comply with match rules. One of the best trigger gauges out there is the Wheeler Professional Digital Trigger Pull Gauge (#ad). With digital display and 1 oz. increments this Pro Trigger Gauge is a great tool for target shooters and gunsmiths, allowing precise trigger settings. This digital gauge boasts accuracy to +/-0.5% over a range of 0 to 12 pounds.
9. Amazon — Lockdown Hidden Storage Shelf, $99.99
⏺️ Great design provides security in a living area
It can be challenging to keep firearms in your house in a manner where they are both secure yet readily accessible. One way to accomplish this is with the Lockdown Hidden Compartment Shelf (#ad). This has a hidden horizontal storage area where you can keep a pistol and other key items. The Lockdown Shelf mounts easily on your wall. With a simple swipe of the included magnetic key, you have instant access to firearms and other important items.
10. Amazon — Digital Microscope, $29.99
⏺️ Very low price on great tool for inspecting bullets, brass, primers
Do you wish you had a way to cheaply and easily inspect your primer pockets, trimmed brass, or pointed bullets? We like this 4.3″ 1080p HD 1000x Zoom Microscope (#ad) that allows you to go from 5X to 1000X with an easy-to-use focus. This advanced electronic magnifying system is priced at just $29.99, a very low price for such a sophisticated device. NOTE: This is a limited time deal that may expire very quickly.
11. TargetSports USA — Self-Inking Stamp for Targets, $5.99
⏺️ Handy tool to stamp your own 2″ bullseyes on target
Are you tired of buying targets or wasting expensive printer ink just to shoot holes in paper? Consider this handy, low-cost Self-Inking Target Stamp. With an easy-to-fill ink reservoir, you can stamp a grid of multiple targets or add 2″ red bullseyes to a printed target. NOTE: This target stamp is listed at 51mm, so it makes bulls 2 inches in diameter.
As an Amazon affiliate, this site can earn revenues through sales commissions.
The U.S. Army Marksmanship Unit regularly published a reloading “how-to” article on the USAMU Facebook page. One excellent “Handloading Hump Day” post covered preparation of once-fired 5.56x45mm brass. This article, the first in a 3-part series, has many useful tips. If you shoot a rifle chambered in .223 Rem or 5.56x45mm, this article is worth reading. You can obtain once-fired Lake City 5.56x45mm brass for less than half the cost of premium .223 Rem brass.
This week, Handloading Hump-Day will answer a special request from several competitive shooters who asked about procedures for morphing once-fired GI 5.56mm brass into accurate match brass for NRA High Power Rifle use. The USAMU has used virgin Lake City (LC) 5.56 brass to win National Championships and set National Records for many years. In this 3-part series, we’ll share techniques proven to wring match-winning accuracy from combat-grade brass.
GI brass has an excellent attribute, worth noting — it is virtually indestructible. Due to its NATO-spec hardness, the primer pockets last much longer than most commercial brass when using loads at appropriate pressures.
Preparing Once-Fired GI 5.56 Brass for Reloading (Part 1 of 3)
Assuming our readers will be getting brass once-fired as received from surplus dealers, the following steps can help process the low-cost raw material into reliably accurate components.
1. Clean the Brass
First, clean the brass of any dirt/mud/debris, if applicable. Depending on the brass’s condition, washing it in a soap solution followed by a thorough rinsing may help. [This step also extends the life of the tumbling media.] Approaches range from low-tech, using gallon jugs 1/2 full of water/dish soap plus brass and shaking vigorously, to more high-tech, expensive and time-consuming methods.
2. Wet-Tumbling Options (Be Sure to Dry the Brass)
When applying the final cleaning/polish, some use tumblers with liquid cleaning media and stainless steel pins for a brilliant shine inside and out, while others take the traditional vibratory tumbler/ground media approach. Degree of case shine is purely personal preference, but the key issue is simple cleanliness to avoid scratching ones’ dies.
If a liquid cleaner is used, be SURE to dry the cases thoroughly to preclude corrosion inside. One method is to dump the wet brass into an old pillow case, then tilt it left/right so the cases re-orient themselves while shifting from corner to corner. Several repetitions, pausing at each corner until water stops draining, will remove most water. They can then be left to air-dry on a towel, or can be dried in a warm (150° F-200° F max) oven for a few minutes to speed evaporation.
Shown below are Lake City cases after cleaning with Stainless Media (STM). Note: STM Case cleaning was done by a third party, not the USAMU, which does not endorse any particular cleaning method.
NOTE: The USAMU Handloading (HL) Shop does not RE-load fired 5.56 brass. We use virgin LC brass with our chosen primer already staked in place. However, our staff has extensive personal experience reloading GI brass for competition, which will supplement the Shop’s customary steps. In handloading, as in life, there are many ways to accomplish any given task. Our suggestions are note presented as the “only way,” by any means. Time for loading/practicing is always at a premium. Readers who have more efficient, alternative methods that maintain top accuracy are invited to share them here.
3. Inspect Every Case
Once dry, inspect each case for significant deformation (i.e., someone stepped on it), damaged mouths/necks and case head/rim damage. Some rifles’ ejectors actually dig small chunks of brass out of the case head — obviously, not ideal for precision shooting. Similarly, some extractors can bend the case rims so badly that distortion is visible when spinning them in one’s fingers. These can be used for plinking, but our match brass should have straight, undamaged rims.
Dented case mouths are common, and these can easily be rounded using a conical, tapered tool, [such as a .223 expander mandrel. A dummy 7.62 or .30-06 cartridge with a FMJ spitzer can also work.] If most of your brass is of one headstamp, this is a good time to cull out any odd cases.
4. Check the Primers Before Decapping
Your clean, dry and inspected brass is now ready for full-length sizing, decapping and re-priming. Historically, primer crimps on GI brass have caused some head-scratching (and vile language) among handloaders. Our next installment will detail efficient, easy and practical methods to remove primer crimp, plus other useful handloading tips. Until next week, Good Shooting!
Accuracy Potential of Mil-Surp 5.56×45 Brass
So, how accurate can previously-fired GI surplus brass be in a good National Match AR-15? Well, here’s a data point from many years ago that might be of interest. A High Power shooter who wrote for the late Precision Shooting magazine took a Bill Wylde-built AR match rifle to a registered Benchrest match. He had no difficulty obtaining consistent 0.5-0.6 MOA accuracy at 200 yards using LC brass and a generic “practice” load that was not tuned to his rifle.
Review Quick Highlights:
Want to see some handgun shooting fun on TV tonight? Today Shooting USA television will feature the 2024 IDPA National Championship on the Outdoor Channel.
Along with SSP and ESP, there are three other main IDPA classes: Custom Defensive Pistol (CDP) for .45 ACPs (mostly 1911 types), Concealed Carry Pistol (CCP), and Revolver (REV). All classes have a minimum power factor. Scores are based on time and shot placement on the IDPA target.
2. Check Out the Forum Classifieds. There are great deals to be found every day in the AccurateShooter 
3. Share a Ride to Matches. Fuel prices are on the rise — Regular-grade gasoline is over $5.00 per gallon in California now and around $3.10/gallon nationwide. With many shooters living 30-100 miles from the nearest range, fuel remains a big part of a shooter’s hobby budget. We’d say 90% of shooters drive solo to matches, often in large, gas-guzzling trucks. If you drive 200 miles round-trip to attend a match in a 20-mpg vehicle, you’ll burn over $31.00 worth of gasoline on your trip. That adds up. By simply sharing the ride with one fellow shooter you cut your fuel expenditures in half. And, if you alternate vehicles with a buddy from one match to the next, you save on vehicle wear and tear. At $0.65/mile (overall operating costs) consider the savings.
4. Use Discount Codes to Save. It’s always smart to check for discount codes before you buy. In the Daily Bulletin, we feature “Deals of the Week” every Monday morning, and we provide discount Coupon Codes when available. These can reduce the price substantially or lower shipping costs. Search codes for Brownells, Creedmoor Sports, EuroOptic, Graf’s, Midsouth, Powder Valley, Sportsman’s Warehouse, KYGUNCO, MidwayUSA, and Precision Reloading. Check your email also — some discount codes are only announced in email newsletters. If you can’t find a Coupon Code for your preferred vendor, visit 
5. Shop for “Demo” Optics. Modern high-quality optics can easily cost $2000.00 or more, often exceeding the value of the rifle on which they are mounted. However, you can often save 20-30% by purchasing demo optics. These are normally display units used at trade shows. They may have slight ringmarks, but otherwise they are “as new”, having never been carried in the field or used on a rifle that has fired live ammo. When purchasing demo scopes, you should always ask about the warranty before consummating the sale. However, most demo scopes from name-brand manufacturers come with full factory warranties. 
6. Train with Rimfire Rifles. Good match-grade centerfire, hand-loaded ammo, counting premium bullets, powder, primers, and brass (figuring 10X loads), can now exceed $1.60 per round. And if your $600 (as chambered and fitted) competition barrel is toast after 1500 rounds, add $0.40 for barrel deprecation per shot. So you’re effectively spending two bucks a round total! By contrast, you can get quite good .22 LR target ammo for under $0.18 per round. Good rimfire barrels last a long, long time, so you don’t have to be concerned about wearing out your barrel quickly. A quality rimfire barrel can retain its accuracy for 7,000 rounds or more. If you run the ballistics, a .22 LR round at 100 yards can emulate the wind drift experienced by a centerfire cartridge at long range. This allows for effective cross-training with much less expensive ammo.
To find out if you have a burr or damage to your crown, you can use an ordinary Q-tip cotton swab. Check the edges of the crown by pulling the Q-tip gently out past the edge of the crown. If you have a burr, it will “grab” the cotton and leave strands behind.
