Bore-tips Swabs, Chamber Cleaners, and Pull-Through Whips

Wouldn’t it be nice to dispense with patches and jags when cleaning your guns? The folks at Super Brush, LLC, had the same idea, so they invented Bore-tips® swabs. These reusable foam “mops” provide 360° of contact with the bore, reaching both the grooves and the lands. Bore-tips thread onto standard cleaning rods. They are offered in a variety of sizes, from .22 caliber up to 12 Gauge. Rifle Bore-tips come in .22 (5.56mm), .243 (6mm), and .308 (7.62mm) calibers. Pistol Bore-Tips are offered for .22, .30, 9mm, .357, .40, and .45 calibers.

We first saw Bore-tips products at the Southwest Nationals a couple years ago. We were intrigued. These foam swabs may be useful for some applications, particularly pistols and shotguns which require minimal brushing. For rifles they do a good job of applying solvents because they hold more liquid than a patch. However, you probably won’t want to abandon your jags and patches. Sometimes a tight-fitting patch is still the best tool for the job. Patches are cheap and it’s easier to discard a used patch, rather than fuss with cleaning foam swabs. But for shotguns (and lightly used pistols), these things make sense.

Bore-tips Claimed Benefits:
• Each tip is reusable and can be cleaned with solvents or soap and water.
• Tough and fiber-free, Bore-tips will not shed or leave lint behind as cotton will.
• FAST PATCHLESS CLEANING — solves the shortcomings of the jag and patch.
• Foam fills the lands and grooves of the rifling, not sliding over the top like a patch.
• Quick threading on a standard 8-32 cleaning rod. Shotgun sizes use a 5/16 x 27 rod.
• Can be used with most commercially available solvents and oils.

AR15 Chamber Cleaner:

Pull-Through Bore-Whips for Quick Cleaning Jobs
Along with the screw-on Bore-tips there are handy pull-through Bore-whips for air guns and rifles. These are offered in .177 for air rifles and .223/5.56 for rimfire and centerfire rifles. We have found these Bore-whips very handy as the .177 version (see below) can also be used for .17 HM2 and 17 HMR rifles.

How to Use Bore-tips

Use a Bore-tip to apply solvent to the barrel. After allowing the solvent time to work, brush the bore to break up any fouling. Next use a clean Bore-tip to push the fouling out the bore. When the now dirty Bore-tip clears the bore, wet it with a little solvent and then squeeze it with an absorbent rag or paper towel, this will blot the dirt off. After blotting the Bore-tip should be clean enough to continue using to remove the fouling until you are finished cleaning. When you are satisfied with the cleanliness of your barrel, use a clean Bore-tip to dry the bore.

Click for Full-Screen Images

How to Clean Bore-tips®

For faster cleaning, apply mineral spirits to the Bore-tip and squeeze/blot into an absorbent rag or paper towel. When the Bore-tip is clean, let dry and reuse. Using soap and water, squeeze to blot out any excess solvent or dirt. Next, wash the Bore-tip with a grease-cutting soap and warm water. Once clean, rinse then let dry completely. See cleaning video below:

Bore-Tips Foam Swab Cleaning Demonstration

Similar Posts:

• New Bore-Tips Foam Bore Swabs for Barrel Cleaning
• Bore Cleaning 101: Speed Up the Job with a Wash Bottle
• Speed Up Bore Cleaning Chores with Wash Bottles
• Speed Up Bore Cleaning Chores by Using Wash Bottles
• Consider Side-Spiking Your Bore Cleaning Patches

Tags: bore, Bore Cleaning, Bore-tip, Brush, Foam, Jag, Patches, Swab, Swab-It